Sharif Digital Repository

Given measurement difficulties, earlier modeling studies have often used some constant ratios to predict lumbar segmental kinematics from measurements of total lumbar kinematics. Recent imaging studies suggested distribution of lumbar kinematics across its vertebrae changes with trunk rotation, lumbar posture, and presence of load. An optimization-based method is presented and validated in this study to predict segmental kinematics from measured total lumbar kinematics. Specifically, a kinematics-driven biomechanical model of the spine is used in a heuristic optimization procedure to obtain a set of segmental kinematics that, when prescribed to the model, were associated with the minimum... 

Background Iatrogenic injuries to paraspinal muscles during posterior lumbar surgery cause a reduction in their contractile cross-sectional area and thus presumably their postoperative activation. This study investigates the effect of such intraoperative injuries on postoperative patterns of muscle activations and spinal loads during various activities using a combined modeling and in vivo MR imaging approach. Methods A three-dimensional, multi-joint, musculoskeletal model was used to estimate pre- and postoperative muscle forces and spinal loads under various activities in upright and flexed postures. According to our in vivo pre- and postoperative (∼ 6 months) measurements in six patients... 

Spinal posture is a crucial input in biomechanical models and an essential factor in ergonomics investigations to evaluate risk of low back injury. In vivo measurement of spinal posture through the common motion capture techniques is limited to equipped laboratories and thus impractical for workplace applications. Posture prediction models are therefore considered indispensable tools. This study aims to investigate the capability of artificial neural networks (ANNs) in predicting the three-dimensional posture of the spine (S1, T12 and T1 orientations) in various activities. Two ANNs were trained and tested using measurements from spinal postures of 40 male subjects by an inertial tracking... 

Range of motion (ROM) of the thoracic spine has implications in patient discrimination for diagnostic purposes and in biomechanical models for predictions of spinal loads. Few previous studies have reported quite different thoracic ROMs. Total (T1-T12), lower (T5-T12) and upper (T1-T5) thoracic, lumbar (T12-S1), pelvis, and entire trunk (T1) ROMs were measured using an inertial tracking device as asymptomatic subjects flexed forward from their neutral upright position to full forward flexion. Correlations between body height and the ROMs were conducted. An effect of measurement errors of the trunk flexion (T1) on the model-predicted spinal loads was investigated. Mean of peak voluntary total... 

Traditional electromyography-assisted optimization (TEMG) models are commonly employed to compute trunk muscle forces and spinal loads for the design of clinical/treatment and ergonomics/prevention programs. These models calculate muscle forces solely based on moment equilibrium requirements at spinal joints. Due to simplifications/assumptions in the measurement/processing of surface EMG activities and in the presumed muscle EMG-force relationship, these models fail to satisfy stability requirements. Hence, the present study aimed to develop a novel stability-based EMG-assisted optimization (SEMG) method applied to a musculoskeletal spine model in which trunk muscle forces were estimated by... 

Evaluation of spinal range of motions (RoMs) and movement coordination between its segments (thorax, lumbar, and pelvis) has clinical and biomechanical implications. Previous studies have not recorded three-dimensional primary/coupled motions of all spinal segments simultaneously. Moreover, magnitude/direction of the coupled motions of the thorax/pelvis in standing posture and lumbopelvic rhythms in the frontal/transverse planes have not been investigated. This study, hence, used an inertial tracking device to measure T1, T5, T12, total (T1-T12) thoracic, lower (T5-T12) and upper (T1-T5) thoracic, lumbar (T12-S1), and pelvis primary and coupled RoMs as well as their movement coordination in... 

Low back pain is the most prevalent orthopedic disorder and the first main cause of poor working functionality in developed as wells as many developing countries. In Absence of noninvasive in vivo measurement approaches, biomechanical models are used to estimate mechanical loads on human joints during physical activities. To estimate joint loads via musculoskeletal models, the calculation of muscle forces are of importance. It is however difficult to estimate muscle forces as the number of muscles, i.e. unknown parameters, is far more than the existing degrees of freedom; the system is highly redundant. Therefore, in this study, instead of muscle forces estimation, their effects (i.e.,... 

Background: The purpose of this study was to propose a methodology for mechanical characterization of the ligaments in subject-specific models of the patellofemoral joint (PFJ) of living individuals. Method: PFJ laxity tests were performed on a healthy volunteer using a specially designed loading apparatus under biplane fluoroscopy. A three-dimensional (3D) parametric model of the PFJ was developed in the framework of the rigid body spring model using the geometrical data acquired from the subject's computed tomography and magnetic resonance images. The stiffness and pre-strains of the medial and lateral PFJ ligaments were characterized using a two-step optimization procedure which minimized... 

Previous studies have measured thoracic Range of Motion (RoM) using either skin-mounted devices or supine CT-imaging and have reported on quite different RoMs. Given the inherent shortcomings of measurements of vertebrae movements from the overlying skin, the present study aims to measure normal RoM of the thoracic spine in the sagittal plane using the upright digital radiography. Lateral radiographs of the thoracic spine were obtained from eight asymptomatic male subjects in upright standing and full forward flexion using a mobile U-arm digital radiographic system. Total (T1-T12), upper (T1-T6), and lower (T6-T12) thoracic RoMs were measured. A throughout comparison of available skin-based... 

Previous studies have measured thoracic Range of Motion (RoM) using either skin-mounted devices or supine CT-imaging and have reported on quite different RoMs. Given the inherent shortcomings of measurements of vertebrae movements from the overlying skin, the present study aims to measure normal RoM of the thoracic spine in the sagittal plane using the upright digital radiography. Lateral radiographs of the thoracic spine were obtained from eight asymptomatic male subjects in upright standing and full forward flexion using a mobile U-arm digital radiographic system. Total (T1-T12), upper (T1-T6), and lower (T6-T12) thoracic RoMs were measured. A throughout comparison of available skin-based... 

Objective: To assess adequacy of the National Institute for Occupational Safety and Health (NIOSH) Lifting Equation (NLE) in controlling lumbar spine loads below their recommended action limits during asymmetric load-handling activities using a detailed musculoskeletal model, that is, the AnyBody Modeling System. Background: The NIOSH committee employed simplistic biomechanical models for the calculation of the spine compressive loads with no estimates of the shear loads. It is therefore unknown whether the NLE would adequately control lumbar compression and shear loads below their recommended action limits during asymmetric load-handling activities. Method: Twenty-four static stoop lifting... 

Evaluation of workers’ body posture in workstations is a prerequisite to estimate spinal loads and assess risk of injury for the subsequent design of preventive interventions. The Microsoft Kinect™ sensor is, in this regard, advantageous over the traditional skin-marker-based optical motion capture systems for being marker-less, portable, cost-effective, and easy-to-use in real workplaces. While several studies have demonstrated the validity/reliability of the Kinect for posture measurements especially during gait trials, its capability to adequately drive a detailed spine musculoskeletal model for injury risk assessments remains to be investigated. Lumbosacral (L5-S1) load predictions of a... 

Spinal posture including thorax/pelvis orientations as well as loads on the intervertebral discs are crucial parameters in biomechanical models and ergonomics to evaluate the risk of low back injury. In vivo measurement of spinal posture toward estimation of spine loads requires the common motion capture techniques and laboratory instruments that are costly and time-consuming. Hence, a closed loop algorithm including an artificial neural network (ANN) and fuzzy logic is proposed here to predict the L5–S1 segment loads and thorax/pelvis orientations in various 3D reaching activities. Two parts namely a fuzzy logic strategy and an ANN from this algorithm; the former, developed based on the... 

Measurements of spinal segment ranges of motion (RoMs), movement coordination, and three-dimensional kinematics during occupational activities have implications in occupational/clinical biomechanics. Due to the large amount of adipose tissues, obese individuals may have different RoMs, lumbopelvic coordination, and kinematics than normal-weight ones. We aimed to measure/compare trunk, lumbar, and pelvis primary RoMs in all anatomical planes/directions, lumbopelvic ratios (lumbar to pelvis rotations at different trunk angles) in all anatomical planes/directions and three-dimensional spine kinematics during twelve symmetric/asymmetric statics load-handling activities in healthy normal-weight... 

Spinal fusion surgery is usually followed by accelerated degenerative changes in the unfused segments above and below the treated segment(s), i.e., adjacent segment disease (ASD). While a number of risk factors for ASD have been suggested, its exact pathogenesis remains to be identified. Finite element (FE) models are indispensable tools to investigate mechanical effects of fusion surgeries on post-fusion changes in the adjacent segment kinematics and kinetics. Existing modeling studies validate only their intact FE model against in vitro data and subsequently simulate post-fusion in vivo conditions. The present study provides a novel approach for the comprehensive validation of a lumbar... 

The recruitment pattern of trunk muscles is determined using a three-dimensional model of the spine with two joints and six symmetric pairs of muscles in which both equilibrium and stability requirements are satisfied. Model predictions are verified using Anybody Modeling System (AMS) and Abaqus. The model is used to test the hypothesis that antagonistic muscle activities are necessary for the spinal stability. The model with stability constraints predicts muscle activities greater than those predicted without stability consideration. In agreement with experimental data, the stability-based model predicts antagonistic muscle activities. It is shown that spinal stability increases with trunk... 

Due to the complexity of the human spinal motion segments, the intervertebral joints are often simulated in the musculoskeletal trunk models as pivots thus allowing no translational degrees of freedom (DOFs). This work aims to investigate, for the first time, the effect of such widely used assumption on trunk muscle forces, spinal loads, kinematics, and stability during a number of static activities. To address this, the shear deformable beam elements used in our nonlinear finite element (OFE) musculoskeletal model of the trunk were either substantially stiffened in translational directions (SFE model) or replaced by hinge joints interconnected through rotational springs (HFE model). Results... 

Epidemiological studies are divided over the causative role of body weight (BW) in low back pain. Biomechanical modeling is a valuable approach to examine the effect of changes in BW on spinal loads and risk of back pain. Changes in BW have not been properly simulated by previous models as associated alterations in model inputs on the musculature and moment arm of gravity loads have been neglected. A detailed, multi-joint, scalable model of the thoracolumbar spine is used to study the effect of BW (varying at five levels, i.e., 51, 68, 85, 102, and 119kg) on the L5-S1 spinal loads during various static symmetric activities while scaling moment arms and physiological cross-sectional areas of... 

Various hybrid EMG-assisted optimization (EMGAO) approaches are commonly used to estimate muscle forces and joint loads of human musculoskeletal systems. Use of EMG data and optimization enables the EMGAO models to account for inter- and intra-individual variations in muscle recruitments while satisfying equilibrium requirements. Due to implications in ergonomics/prevention and rehabilitation/treatment managements of low-back disorders, there is a need to evaluate existing approaches. The present study aimed to compare predictions of three different EMGAO and one stability-based optimization (OPT) approaches for trunk muscle forces, spinal loads, and stability. Identical measured... 

A number of musculoskeletal models of the human spine have been used for predictions of lumbar and muscle forces. However, the predictive power of these models might be limited by a commonly made assumption; thoracic region is represented as a single lumped rigid body. This study hence aims to investigate the impact of such assumption on the predictions of spinal and muscle forces. A validated thoracolumbar spine model was used with a flexible thorax (T1–T12), a completely rigid one or rigid with thoracic posture updated at each analysis step. The simulations of isometric forward flexion up to 80°, with and without a 20 kg hand load, were performed, based on the previously measured...