Sharif Digital Repository

In this paper, two very simple and accurate equations are introduced that enable geotechnical engineers to determine the undrained ultimate bearing capacity of shallow strip foundations resting on two-layered clays. Results of the analyses show that in the case of weak-overstrong clay, usually general shear failure occurs, and in the case of strong-over-weak clay, the soil will most likely experience punching failure with a large amount of plastic settlement before it reaches its ultimate bearing capacity. This study applied the finite-difference method using a computer program to evaluate the undrained bearing capacity for all cases analyzed. The Mohr-Coulomb failure criterion was used for... 

Metallic nanoparticles (NPs) have not been effective in improving the overall performance of the cells with micrometer-thick absorbing layers mainly due to the parasitic optical dissipation in the metal. Here, using both experiment and theory, we demonstrate that aggregates of metallic NPs enhance the light absorption of dye-sensitized solar cells of a few micrometer-thick light absorbing layers. The composite electrode containing the optimal concentration of 5 wt% Au@SiO2 aggregates shows the enhancement of 80% and 52% in external quantum efficiency and photocurrent density, respectively. The superior performance of the aggregates relative to NP is attributed to their larger scattering... 

In this research, polypropylene (PP) nanocomposite films were prepared by melt intercalation method and their properties have been evaluated. To facilitate the formation of either intercalated or exfoliated nanocomposites, ethylene vinyl acetate copolymer (EVA) was used as a compatibiliser. Morphology of composites was determined by X-ray Diffraction (XRD) and transmission electron microscopy (TEM). XRD and TEM analyses confirmed that increasing of EVA content leads to achievement of intercalated nanocomposites. Furthermore, differential scanning calorimetry (DSC) measurement indicated a decrease in crystallinity, melting point and crystallization temperature. Also, permeability tests showed... 

Chitosan was crosslinked with different amount of glutaraldehyde to prepare appropriate hydrogels to be used as drug delivery system. The swelling behavior of freeze-dried hydrogels in aqueous media at different temperature and pHs has been examined. The swelling, porosity and biocompatibility behavior of samples were investigated to check effects of polymer/polymer and polymer/drug interactions on these system characteristics. Obtained experimental results illustrates that with increasing crosslinking agent from 0.068 to 0.30, swelling of the prepared samples degrees from 1200% to 600% and pore diameters change from 100 to 500 μm. To investigate systems biocompatibility in gastric... 

Among the various techniques of electronic warfare in the sea, chaff has particular importance due to its easy application and its impact on the victim radar. Despite the great history of chaff, the significant research has not been published on its recognition. It is difficult to study the behavior of chaff because of the impossibility of chaff tests in an unechoic chamber. Therefore simulation would be a suitable alternative. In this paper, the simulations of symmetric feature of chaff and target are presented and it is used to propose a processing structure, based on various classifiers, for discrimination between chaff and target. Moreover the comparison between discrimination capability... 

Inclusion of nano-clays into hydrogels is an efficient approach to produce nanocomposite hydrogels. The introduction of nano-clay into hydrogels causes an increase in water absorbency. In the present work, Nanocomposite hydro-gels based on kappa-carrageenan were synthesized using sodium montmorillonite as nano-clay. Acrylamide and meth-ylenebisacrylamide were used as monomer and crosslinker, respectively. The structure of nanocomposite hydrogels was investigated by XRD and SEM techniques. Swelling behavior of nanocomposite hydrogels was studied by varying clay and carrageenan contents as well as methylenebisacrylamide concentration. An optimum swelling capacity was achieved at 12% of sodium... 

In the present study, the out-of-phase thermomechanical fatigue (OP-TMF) behavior of a cast aluminum-silicon-magnesium alloy, the A356.0 alloy which has been widely used in diesel engine cylinder heads, is compared to room-temperature and high-temperature low cycle fatigue (RT-, HT-LCF) behaviors. For this purpose, strain/temperature-controlled isothermal and non-isothermal fatigue tests were performed based on realistic loading conditions in cylinder heads. Fatigue tests results showed that the plastic strain increased during cycles under constant mechanical strain amplitude, while the specimen failed. Under LCF loadings, the cyclic hardening occurred at low temperatures for the A356.0... 

Machine learning (ML) is generating new opportunities for innovative research in energy economics and finance. We critically review the burgeoning literature dedicated to Energy Economics/Finance applications of ML. Our review identifies applications in areas such as predicting energy prices (e.g. crude oil, natural gas, and power), demand forecasting, risk management, trading strategies, data processing, and analyzing macro/energy trends. We critically review the content (methods and findings) of more than 130 articles published between 2005 and 2018. Our analysis suggests that Support Vector Machine (SVM), Artificial Neural Network (ANN), and Genetic Algorithms (GAs) are among the most... 

The general approach to fault tolerance in uniprocessor systems is to maintain enough time redundancy in the schedule so that any task instance can be re-executed in presence of faults during the execution. In this paper a scheme is presented to add enough and efficient time redundancy to the Earliest-Deadline-First (EDF) scheduling policy for periodic real-time tasks. This scheme can be used to tolerate transient faults during the execution of tasks. We describe a recovery scheme which can be used to re-execute tasks in the event of transient faults and discuss conditions that must be met by any such recovery scheme. For performance evaluation of this idea a tool is developed. © 2007 IEEE  

The reliable transfer in Network on Chips (NoCs) can be threatened by crosstalk fault occurring in wires. Crossstalk fault is due to inter-wire coupling capacitance that based on the patterns of transitions appearing on the wires, significantly limits the reliability of NoCs. Among these transitions, 101 and 010 bit patterns impose the worst crosstalk effects to wires. This work intends to increase the reliability of NoCs against crosstalk faults by applying an improved Fibonacci-based numeral system, called Doubled-Penultimate Fibonacci (DP-Fibo). In the DP-Fibo coding algorithm, code words without ‘101’ and ‘010’ bit patterns are produced to reduce crosstalk faults. Experimental results... 

In the present work, specimens were cut out from St-37 plates with 19 mm thickness. The thickness of plates was reduced to 12.5 mm by milling and grinding operations. Then a standard V-shaped fillet was made on one edge of the plates. Two plates were butt-welded by standard metal arc gas (MAG) welding process. Residual stresses induced by welding were measured on 20 specimens by centre hole drilling. Load controlled axial fatigue tests were carried out to determine the fatigue life of specimens. Crack growth rates were obtained from experiment. Fractography of specimens was performed. Genetic Algorithm (GA) was employed for prediction of residual stress value in weldments using the crack... 

In this work, we implement some analytical techniques such as the Exp-function, Tanh, and extended Tanh methods for solving nonlinear partial differential equation, which contains sine terms, its name Double Sine-Gordon equation. These methods obtain exact solutions of different types of differential equations in engineering mathematics  

The qualitative effects of residual stress parameters on fatigue crack growth are investigated using Monte Carlo probabilistic analysis technique. These parameters include the maximum residual stress,σ0, half-width of the tensile residual stress region, b, and the redistribution of residual stress parameter, β. A normal distribution is assumed for all parameters considered in the investigation and fatigue life is determined using Forman equation. The results indicate that: (i) fatigue life decreases nonlinearly if the mean of random maximum residual stress and the half-width of tensile residual stress region increases; (ii) fatigue life increases nonlinearly if the rate of residual stress... 

In this paper residual stresses induced by butt metal arc gas welding (MAGW), in accordance with ASTM E837, are determined by hole drilling. The results are analyzed by probabilistic methods. Also, the effect of fatigue life on relaxation of welding residual stress is investigated. The specimens are tested to measure fatigue life and crack growth rates in accordance with ASTM E466 for force controlled amplitude axial fatigue testing. © 2008 Verlag Stahleisen GmbH, Düsseldorf  

The effect of contact geometry on fretting fatigue life was investigated by experiments and numerical simulation. The experiments were conducted for flat and cylindrical pads under the same contact normal force. The post-test examinations including crack growth measurements and fractography were carried out using optical and scanning electron microscopy (SEM). Numerical simulations of pad-specimen assembly with and without crack were performed using a finite element (FE) analysis. The experimental study revealed that the rate of crack growth was higher at the early stages of fretting fatigue for cylindrical pads. This stage corresponds to a higher KII for cylindrical contact model. After... 

A variational theory (VT), in which the potential energy of a real system is evaluated relative to the hard-sphere system, was used to investigate the medium's effects on the pair potential parameters. By adding the medium's effects to the isolated pair potential, the concept of an 'effective pair potential' (EPP) was introduced. The EPP parameters were compared with those of the average effective pair potential (AEPP) for Ar, which showed the importance of the medium effects and the long range interactions of the AEPP in dense fluids. The study showed that the depth parameter of the AEPP is much larger than that of the EPP  

In this article, out-of-phase thermo-mechanical fatigue (TMF) behaviours of light alloys were investigated in comparison to their high temperature low cycle fatigue (LCF) behaviours. For this objective, strain based fatigue tests were performed on the A356 aluminium alloy and on the AZ91 magnesium alloy. Besides, TMF tests were carried out, where both strain and temperature changed. The fatigue lifetime comparison demonstrated that the TMF lifetime was less than that one under LCF loadings at elevated temperatures for both light alloys. The reason was due to severe conditions in TMF tests in comparison to LCF tests. The temperature varied in TMF test but it was constant under LCF loadings.... 

In the present paper, thermo-mechanical fatigue (TMF) and low cycle fatigue (LCF) or isothermal fatigue (IF) lifetimes of a cast magnesium alloy (the AZ91 alloy) were studied. In addition to a heat treatment process (T6), several rare elements were added to the alloy to improve the material strength in the first step. Then, the cyclic behavior of the AZ91 was investigated. For this objective, strain-controlled tension-compression fatigue tests were carried out. The temperature varied between 50 and 200. °C in the out-of-phase (OP) TMF tests. The constraint factor which was defined as the ratio of the mechanical strain to the thermal strain, was set to 75%, 100% and 125%. For LCF tests,... 

This paper presents the fatigue lifetime of an aluminum-silicon-magnesium alloy, widely used in diesel engine cylinder heads, both with and without a thermal barrier coating (TBC) system. The coating system in this study consists of two layers including a 150 μm thick metallic bond coat and a zirconium oxide top coat 350 μm thick. These coating layers were applied on the substrate of A356.0 alloy by air plasma thermal spraying. The isothermal fatigue tests were conducted in low cycle fatigue (LCF) regime at various temperatures. Out-of-phase thermo-mechanical fatigue (OP-TMF) tests were also performed at different maximum temperatures and constraint factors. Experimental results demonstrate...