Sharif Digital Repository

The concepts of thermal radiation heat transfer are not tangible for many students. Experiments relied on various parameters can clarify the concepts of this mode of heat transfer.A lab-scale set up is described to study the thermal radiation heat transfer experiments. An electrical circuit of the thermopile sensor is designed and manufactured to provide experimental data.The validity of Inverse Square, Stefan-Boltzmann, and Kirchhoff Laws are investigated experimentally in the setup. Results indicate that, it is necessary to consider temperature shifts in the thermopile cold junction which is a potential source of error. Therefore, the output voltage, corresponding to the sensor... 

Microbial fuel cells (MFCs) represent a new method for simultaneous wastewater treatment and biological electricity generation. In this study, petrochemical wastewater with 8000 mg/l of chemical oxygen demand was examined in a membrane-less single chamber MFC. Effects of wastewater concentration as substrate for microbial oxidation, and anode material (stainless steel or carbon brush) were investigated as designing parameters  

Background: Purified terephthalic acid (PTA) wastewater from a petrochemical complex was utilized as a fuel in the anode of a microbial fuel cell (MFC). Effects of two important parameters including different dilutions of the PTA wastewater and pH on the performance of the MFC were investigated. Methods: The MFC used was a membrane-less single chamber consisted of a stainless steel mesh as anode electrode and a carbon cloth as cathode electrode. Both power density and current density were calculated based on the projected surface area of the cathode electrode. Power density curve method was used to specify maximum power density and internal resistance of the MFC. Results: Using 10-times,... 

Wastewater of purified terephthalic acid (PTA) from a petrochemical plant was examined in a membrane-less single chamber microbial fuel cell for the first time. Time course of voltage during the cell operation cycle had two steady phases, which refers to the fact that metabolism of microorganisms was shifted from highly to less biodegradable carbon sources. The produced power density was 31.8 mW m-2 (normalized per cathode area) and the calculated coulombic efficiency was 2.05 % for a COD removal of 74 % during 21 days. The total removal rate of different pollutants in the PTA wastewater was observed in the following order: (acetic acid) > (benzoic acid) > (phthalic acid) > (terephthalic... 

The paper aims at investigating the microstructure, failure mode transition, peak load and energy absorption of DP600 dual phase steel during the tensile-shear test. It was found that the welding current has profound effect on the load–displacement characteristics. In the low welding current, welds failed in interfacial failure mode. Increasing welding current resulted in sufficient weld nugget growth to promote double-sided pullout failure mode with improved mechanical properties. Further increase in the welding current caused expulsion and failure mode was changed to single-sided pullout with reduced energy absorption capability. It was found that the fusion zone size is the key parameter... 

The paper aims at investigating the microstructure, failure mode transition, peak load and energy absorption of DP600 dual phase steel during the tensile-shear test. It was found that the welding current has profound effect on the load–displacement characteristics. In the low welding current, welds failed in interfacial failure mode. Increasing welding current resulted in sufficient weld nugget growth to promote double-sided pullout failure mode with improved mechanical properties. Further increase in the welding current caused expulsion and failure mode was changed to single-sided pullout with reduced energy absorption capability. It was found that the fusion zone size is the key parameter... 

In recent years, many efforts have been made in the field of computational modeling of cancerous tumors, in order to obtain a better understanding and predictions of their growth patterns. Furthermore, constraint-based modeling of metabolic networks has become increasingly popular, which is appropriate for the systems-level reconstruction of cell physiology. The goal of the current study is to integrate a multiscale agent-based modeling framework with a constraint-based metabolic network model of cancer cells in order to simulate the three dimensional early growth of avascular tumors. In order to develop the integrated model, a previously published generic metabolic network model of cancer... 

The paper addresses the microstructure and failure characteristics of dissimilar resistance spot welds between austenitic stainless steel and ferritic stainless steel. The fusion zone (FZ) of dissimilar welds exhibited complex microstructure consisting of ferrite, austenite and martensite. The development of this triplex structure in the FZ was explained by analysing the phase transformation path and austenite stability. Results showed that all dissimilar welds failed in partial thickness-partial pull-out failure mode. It was shown that the fraction of the nugget fracture of the weld is reduced by increasing the FZ size improving the mechanical performance of the weld. Peak load and energy... 

Weldability is one of the key requirements for automotive materials. This two-part paper aims at understanding the metallurgical phenomena during resistance spot welding of stainless steels, as interesting candidates for automotive body in white. Part I addresses the phase transformations in the fusion zone of three types of stainless steels including austenitic, ferritic and duplex types. The solidification and solid state phenomena including columnar to equiaxed transition, ferrite– austenite post-solidification transformation, martensitic transformation and carbide precipitation are discussed. Particular attention is given to the effect of high cooling rate of resistance spot welding... 

Implementation of new materials in automotive body-in-white requires through knowledge of their metallurgical response to welding process thermal cycle. This two-part paper aims at understanding the physical and mechanical metallurgy of stainless steels, as interesting candidates for automotive application, during resistance spot welding. The second part addresses the phase transformations in the heat affected zone of three types of stainless steels including austenitic, ferritic and duplex steels. Failure modes and mechanical properties of stainless steel resistance spot welds are discussed. The peak load and energy absorption of stainless steel resistance spot welds are compared with... 

Resistance spot welding was used to join austenitic stainless steel and galvanized low carbon steel. The relationship between failure mode and weld fusion zone characteristics (size and microstructure) was studied. It was found that spot weld strength in the pullout failure mode is controlled by the strength and fusion zone size of the galvanized steel side. The hardness of the fusion zone which is governed by the dilution between two base metals, and fusion zone size of galvanized carbon steel side are dominant factors in determining the failure mode. © 2007 Elsevier B.V. All rights reserved  

In the present paper, effects of welding current, welding time, electrode pressure and holding time on the weld nugget size were studied. A failure mechanism was proposed to describe both interfacial and pullout failure modes. This mechanism was confirmed by SEM investigations. In the light of this mechanism, the effect of welding parameters on static weld strength and failure mode was studied. Then, an analytical model was proposed to predict failure mode and to estimate minimum nugget diameter (critical diameter) to ensure pullout failure mode in shear tensile test. On the contrary to existing industrial standards, in this model, critical nugget diameter is attributed to metallurgical... 

Background: It has been previously shown that palindromic sequences are frequently observed in proteins. However, our knowledge about their evolutionary origin and their possible importance is incomplete. Results: In this work, we tried to revisit this relatively neglected phenomenon. Several questions are addressed in this work. (1) It is known that there is a large chance of finding a palindrome in low complexity sequences (i.e. sequences with extreme amino acid usage bias). What is the role of sequence complexity in the evolution of palindromic sequences in proteins? (2) Do palindromes coincide with conserved protein sequences? If yes, what are the functions of these conserved segments?... 

This paper addresses the microstructure properties relationship of wide gap brazed Inconel 738LC. Amdry 718 and a Ni-Cr-Fe-Si-B alloy were used as high melting particles (HMPs) and low melting particles (LMPs), respectively. The effect of the amount of LMPs, 30, 40, and 50 pct, on the microstructure and the shear strength of the joint, was investigated. The microstructure in the brazing zone consists of Ni-based solid solution and eutectic-type microconstituents that is nickel-rich and chromium-rich borides. Nickel-rich borides only observed in the presence of the high amount of LMPs, because of the low Cr-B ratio in the filler alloy. At the brazing/base metal interface, high diffusion of... 

The effects of weld nugget size and expulsion on the performance of low carbon steel resistance spot weld have been investigated in the present paper. Failure mode, peak load and failure energy obtained in tensile-shear test have been used to describe the performance of spot weld. The influence of voids and porosity as well as electrode indentation associated with expulsion on peak load and failure energy is discussed. The results showed that although expulsion does not reduce the load carrying capacity of spot welds, it decreases their energy absorption capability which was attributed to the change of failure location due to excessive electrode indentation associated with expulsion. © 2008... 

This study investigated the effect of intercritical heat treatment temperature on the tensile properties, work hardening and corrosion resistance of dual phase steel. Ferrite-martensite dual phase steel with different martensite volume fractions were obtained after heat treatment at different intercritical temperatures. Microstructure, mechanical properties of steel were measured and the corrosion resistance was evaluated via polarization test. Tensile strength of the specimens increased by increasing the martensite volume fraction up to 48.2%. Further increase in martensite volume fraction led to decrease in tensile strength. Work hardening behavior analyzing showed that in DP steel with...