Sharif Digital Repository

The development and use of design methods for control structures has grown significantly in recent decades. In this study, a systematic plantwide control procedure proposed by Skogestad, has been used. The main idea of suggested method is based on the self-optimizing variables. One of the advantages of this method of designing a control structure is considering the economic optimization of the process in most stages of its implementation. The indirect and direct dimethyl ether synthesis from natural gas feed have been investigated in this study. In this research, indirect and direct dimethyl ether synthesis processes are simulated with Aspen Plus V10 and degree of freedom analysis is done.... 

The system considered on this structure is for the design on mid-high Buildings from 15 and 20 floors above the base level and n floors below the base level and the limitation of the number of floors is due to the computer facility and restrictions. There is going to be an irregularity in some chosen floor at lower-floor, mid-floor, or upper-floor which is assuming one floor from the structure to have a different height with respect to the others. The height of the considered floor is going to increase up to 25% with respect to the other floors and the design of outriggers with these three assumptions is going to be assessed separately. In this system, a central core of steel is constructed... 

In this manuscript we used the method of coset construction to describe theories of spontaneous symmetry breaking. The mathematical details are included in chapter 2. The utility of the method is that without any knowledge of the UV part of a theory we can construct IR part by just knowing the symmetry breaking pattern. We used the method for some symmetry breaking patterns to construct general relativity, massive gravity and also some symmetry breaking patterns corresponding to conformal gravity  

Today, telecommunication links transmit information wirelessly at high rates; The transmission channel is not ideal and the transmitted signal undergoes changes in the channel and then reaches the receiver; Also, the processing blocks in the transmitter and receiver are not completely similar and ideal; These two factors make it difficult for the receiver to recover the transmitted information and actually receives a signal that bears little resemblance to the transmitted signal. The most important effect that the channel has on the transmitted signal is due to the multi-path of the channel between the transmitter and the receiver, which causes a signal to reach the receiver through the... 

This thesis addresses cuff-less blood pressure (BP) estimation, for systolic blood pressure (SBP) and diastolic blood pressure (DBP) estimation with the aid of the processing of vital signals. Both with and without calibration per person approaches for BP estimation are considered. A data acquisition hardware is designed for high-resolution sampling of phonocardiogram (PCG), Photoplethysmogram (PPG) and electrocardiogram (ECG). Using these signals, pulse transit time (PTT) and pulse arrival time (PAT) indexes, which would be used for BP estimation with calibration, are extracted. For the BP estimator model using the calibration, A nonlinear model based on PTT or PAT, via modeling the vessels... 

The purpose of this study is to simulate a turbulent premixed flame with the help of the Laminar Flamelet Decomposition method. Numerical simulation is considered the main approach for studying this flame. A Bunsen-type premixed burner, which has a novel approach to making different levels of turbulence, has been used for modeling the premixed flame. To reduce the cost of numerical calculations, the Reynolds-averaged Navier-Stokes approach has been chosen for the CFD simulation. In this study, the Laminar Flamelet Decomposition model is the main combustion model for analyzing the turbulent premixed flame and with this method, the rate of reactions for all the reaction species will be... 

In most real combustion systems, flow is turbulent (e.g., diesel engines). Therefore, a reliable turbulence modeling approach is necessary to design and analyze a system with turbulent flow. Direct numerical simulation (DNS), Large eddy simulation (LES), and Reynolds-averaged Navier-Stokes (RANS) are the three most mature Computational fluid dynamics (CFD) methods for turbulent flow simulations. Because of LES’s good accuracy and acceptable computational cost. In this project, LES is chosen to simulate the turbulent flow field.Modeled turbulence subgrid scales' interaction with nonlinear flow parameters, needs modeling. In supercritical and transcritical conditions, Equation-of-state is a... 

An a priori analysis is performed to assess the performances of Laminar Flamelet Decomposition (LFD) and Conditional Source-term Estimation (CSE) methods in predicting conditional and unconditional filtered production rates and mass fractions for turbulent premixed flames over a wide range of Karlovitz numbers, which is an indicator for the level of turbulence-chemistry interaction in premixed combustion.In LFD, it is assumed that a turbulent flame is composed of strained laminar flamelets. By presuming the functional form of the probability density function (PDF) of the progress variable and inverting the integral equation for the unconditional filtered mass fractions of one of the species,... 

Recently, millimeter wave imaging (MMWI) technology is given more attention. This is as a result of three facts. First, despite the infrared or optical cameras, these systems can image a target, which is obscured by one or more optically barriers. Second, the electronics circuits in this band have seen great achievements in the current decade, which facilitate the implementation of MMWI structures. Third, there is no known health hazard for the systems operating in this band with moderate power. Therefore, in this project, a MMWI system based on compressed sensing (CS) for the concealed weapon detection application is proposed. This design consists of a linear antenna array, an appropriate... 

The burners studied in the combustion principles have different types due to the configuration of different types of flames, each of them studies a specific phenomenon of combustion, so researchers need to design burners with the ability to: create different types of combustion flow regimes, changing in mixing rate and performance at critical points are felt more and more. This document describes the process of designing and manufacturing a turbulent jet burner with variable mixing ratio and the ability to create a diverse range of flow regimes and different flame configurations. Mixing rate is the most important characteristic in the stability of premixed flames, so the distinctive feature... 

In this study, using a non-interference experimental method, the chemical luminosity of CH* in co-flow diffusion flames with soot and using natural gas hydrocarbon in a laminar flow regime has been investigated. In addition to experimental research, in current research, numerical simulation has been used to extract information such as temperature field, mass fraction of species, and flow structure and comparison and validation with experimental results. Numerical simulation has been used to simulate the mechanism of CH* species formation. Two different mechanisms have been used. In addition, the Soot simulation model from the Moss-Brookes model and radiation heat transfer mechanism... 

We live in the cyber era in which network-based technologies have become omnipresent. Meanwhile, threats and attacks are rapidly growing in cyberspace. Nowadays, some signature-based intrusion detection systems try to detect these malicious traffics. However, as new vulnerabilities and new zero-day attacks appear, there is a growing risk of bypassing the current intrusion detection systems. Many research studies have worked on machine learning algorithms for intrusion detection applications. Their major weakness is to consider the different aspects of network security concurrently. For example, continuous concept drift in normal and abnormal traffic, the permanent appearance of zero-day... 

Statistical process control charts have been applied to the health care practices for quite same time. This work aims at investigating the merits to of applying process control chart to the survival time of the patients suffering from gastric cancer-who go though the surgical treatment. Based on accelerated failure time regression models we adopt risk adjusted control chart to monitor the surgical outcome. The monitoring process will we performed continuously based on a likelihood ratio test. The result indicate that this risk adjusted model can provide better estimation for the risk adjustment model parameters. As expected, the proposed risk-adjusted control charts can achieve a better... 

Internet of things (IOT) interconnects a system of low power embedded devices that each of them has a unique identifier, without human intervention. The number of devices of IOT increases every day, therefor routing in the network of IOT is an important challenge. So, Internet Engineering Task Force (IETF) propose a protocol for routing low power and lossy networks in 2012, which is named RPL. Considering the power supply limitation of devices in the network, utilizing energy-aware policies within the RPL is so important. Meanwhile, objective functions have a vital role in the consuming energy. Also, energy consumption determines the lifetime of nodes. Since many of devices are placed in... 

The development of wind turbine blades model that accurately predict wind turbine thrust in a full range of applicable wind speed has provided a powerful and reliable source for simulation of horizontal axis wind turbine power and thrust force that serves as a valuable tool for wind turbine design and performance analysis. A single-element blade model that reduces the rotor blade characteristics to a lift and drag coefficient vs. angle-of-attack formulation was found to describe accurately the rotor characteristics over a wide operating range. Measurements of wind speed and altitude of wind turbine installation location, rotor speed, and provided thrust is within less than 2% over a wide... 

In this study, the concept of dynamic capabilities is extended to strategic management of public sector organizations. For this purpose, an extensive literature review is performed on strategic management of public and non-profit organizations to identify the main characteristics of them, and the essential differences of these organisations with private sector. Afterwards, the literature on dynamic capabilities is reviewed to distinguish their characteristics and operating process in private organizations. Following the results of the previous sections, i.e. “performance and characteristics of dynamic capabilities in private organizations” and “characteristics of public organizations”, some... 

Study of the structural flexibility of large-scale wind turbine components on aeroelastic performance is important under the existence of critical atmospheric conditions. Prediction and control the critical deformations, identifying maximum local deformation and modeling the forces involved, are required. Aeroelasticity analysis is a suitable method for studying the coupling effects of wind turbine aerodynamics, dynamics and structures. This research has been done by modeling wind turbine components including blades, hub, nacelle and tower, taking into account aerodynamic couplings, dynamics and structures. Considering the large scale of reference wind turbine, nonlinear equations have added...