Sharif Digital Repository

This research aims to investigate the thermo-hydraulic characteristics of flow in the shell side of spiral-wound heat exchangers with consistent shell geometry. To achieve this end, three-dimensional computational fluid dynamics is employed. Geometrical configuration of spiral-wound heat exchangers can be completely determined by knowing six primary parameters including start factor, tube outside diameter, number of tubes in the first layer, number of layers, longitudinal pitch, and radial pitch. Dividing the longitudinal and radial pitches by tube outside diameter, the six primary geometrical parameters reduce to five non-dimensional parameters. The effects of number of tubes in the first... 

Heat transfer between heat exchangers and the surrounding environment, referred to as heat-in-leak, is a crucial phenomenon in the cryogenic applications which can substantially degrade the heat exchanger performance. Present research is organized to investigate the mechanism of heat transfer between the shell-side fluid and the shell wall of spiral wound heat exchangers (SWHEs) to determine the heat transfer coefficient used in the heat-in-leak calculations. The heat transfer characteristics are studied using computational fluid dynamics (CFD) tools. First, 20 dissimilar SWHE models with respect to the geometrical parameters are built and then numerically simulated at different Reynolds... 

In this paper, heat transfer and pressure drop of air in the radiator of an internal combustion engine automobile were investigated. First, three types of fins including louvered, triangular vortex generator and rectangular vortex generator were modeled and their performance were compared with a plain fin. Effects of adding antifreeze in volume ratios of 40, 50 and 60% on the performance of louvered and rectangular vortex generator fins were investigated. Finally, the effects of adding copper oxide and aluminum oxide nanoparticles on the heat transfer improvement of louvered and rectangular vortex generator fins were simulated. The results demonstrated that louvered fin had the highest heat... 

In this study, a novel type of LHP is innovated, fabricated, and its performance is assessed by numerous experiments. Compared to conventional LHPs, this novel design has some modifications in its evaporator and reservoir configuration. This particular type has a simpler and less costly fabrication procedure compared to other LHPs and it yields acceptable performance. Additionally, a novel method is introduced to control the temperature distribution in the system. A steel ball is placed in the evaporator to actively control the operating temperature. The ball is moved by two magnets installed outside of the evaporator. Moreover, a steady-state one-dimensional mathematical model of the... 

Purpose: Spiral-wound heat exchangers (SWHEs) are widely used in different industries. In special applications, such as cryogenic (HEs), fluid properties may significantly depend on fluid temperature. This paper aims to present an analytical method for design and rating of SWHEs considering variable fluid properties with consistent shell geometry and single-phase fluid. Design/methodology/approach: To consider variations of fluid properties, the HE is divided into identical segments, and the fluid properties are assumed to be constant in each segment. Validation of the analytical method is accomplished by using three-dimensional numerical simulation with shear stress transport k-ω model, and... 

Purpose: Spiral-wound heat exchangers (SWHEs) are widely used in different industries. In special applications, such as cryogenic (HEs), fluid properties may significantly depend on fluid temperature. This paper aims to present an analytical method for design and rating of SWHEs considering variable fluid properties with consistent shell geometry and single-phase fluid. Design/methodology/approach: To consider variations of fluid properties, the HE is divided into identical segments, and the fluid properties are assumed to be constant in each segment. Validation of the analytical method is accomplished by using three-dimensional numerical simulation with shear stress transport k-ω model, and... 

The main function of a fired heater in a petrochemical site is to produce supersaturated steam. Due to extremely difficult working conditions and high temperatures, there is a very high probability of failures in different parts of a fired heater. In the fired heater under study, tube guides are frequently damaged due to malfunctions and fractures in bolt connections. To investigate the nature of such fractures, Computational Fluid Dynamics (CFD), Finite Element (FE) method, Charpy impact test and fractography were used. To obtain the temperature of various components of the fired heater, a CFD analysis was carried out by considering the combustion process and modeling the central and side... 

In this study, a new mathematical programming approach for solving the joint timetabling and train stop planning problem in a railway line with double-track segments is proposed. This research aims to design an optimized train timetable subject to the station- capacity and time-dependent dwell time constraints. The objective function is to maximize the railway infrastructure capacity by minimizing the schedule makespan. The problem is formulated as a particular case of blocking permutation flexible flow shop scheduling model with dynamic time window constraints. Due to the combinatorial nature of the problem, heuristic algorithm and bound tightening methods are proposed that generate... 

A novel intelligent semi-active control system for an eleven degrees of freedom passenger car's suspension system using magnetorheological (MR) damper with neuro-fuzzy (NF) control strategy to enhance desired suspension performance is proposed. In comparison with earlier studies, an improvement in problem modeling is made. The proposed method consists of two parts: a fuzzy control strategy to establish an efficient controller to improve ride comfort and road handling (RCH) and an inverse mapping model to estimate the force needed for a semi-active damper. The fuzzy logic rules are extracted based on Sugeno inference engine. The inverse mapping model is based on an artificial neural network... 

Using CNG as an additive for gasoline is a proper choice due to higher octane number of CNG enriched gasoline with respect to that of gasoline. As a result, it is possible to use gasoline with lower octane number in the engine. This would also mean the increase of compression ratio in SI engines resulting in higher performance and lower gasoline consumption. Over the years, the use of simulation codes to model the thermodynamic cycle of an internal combustion engine have developed tools for more efficient engine designs and fuel combustion. In this study, a thermodynamic cycle simulation of a conventional four-stroke spark-ignition engine has been developed. The model is used to study the... 

With the declining energy resources and increase of pollutant emissions, a great deal of efforts has been focused on the development of alternatives for fossil fuels. One of the promising alternative fuels to gasoline in the internal combustion engine is natural gas [1-5]. The application of natural gas in current internal combustion engines is realistic due to its many benefits. The higher thermal efficiency due to the higher octane value and lower exhaust emissions including CO2 as a result of the lower carbon to hydrogen ratio of the fuel are the two important feature of using CNG as an alternative fuel. It is well known that computer simulation codes are valuable economically as a cost... 

Gaining insight into possible vibratory responses of dynamical systems around their stable equilibria is an essential step, which must be taken before their design and application. The results of such a study can significantly help prevent instability in closed-loop stabilized systems by avoiding the excitation of the system in the neighborhood of its resonance. This paper investigates nonlinear oscillations of a rotary inverted pendulum (RIP) with a full-state feedback controller. Lagrange’s equations are employed to derive an accurate 2-DoF mathematical model, whose parameter values are extracted by both the measurement and 3D modeling of the real system components. Although the governing... 

A suction-controlled ring device has been developed to continuously measure the coefficient of lateral soil pressure in deformable unsaturated soil samples from the at-rest to the active condition under application of increasing vertical pressure and controlled matric suction. The device incorporates a thin aluminum specimen ring equipped with horizontal strain gages for recording the lateral soil strains. In addition, a sensor recording water volume changes is utilized to continuously monitor the degree of saturation of the soil sample during tests. The matric suction within the soil texture is controlled using the axis translation technique. In order to verify the performance of the ring... 

We introduce a new smooth, non-toxic, biocompatible method for cross-linking of gum tragacanth (GT), a polysaccharide of natural origin, in order to serve as a new supporting matrix for immobilization systems. The modified gum is used as a matrix for the catalysis of the conversion of benzyl penicillin to 6-aminopenicillanic acid (6-APA) by means of Escherichia coli ATCC11105 with penicillin G acylase (PGA) activity. The results show that GT beads can not only serve as a proper matrix for immobilization, but show enhanced hydrolysis rate and stability compared to other immobilization systems used for this reaction. This signifies the potential of GT as a biocompatible matrix for... 

The Class-E power amplifier has been widely studied and formulated in the literature. Although the majority of reported inductive coupling wireless power transfer (WPT) systems use a class-E power amplifier for driving the primary coil, still there is a lack of a comprehensive study on class-E circuit dedicated to WPT, providing a set of closed form design equations for proper class-E operation. This paper presents the required design equations needed to design a 'true' class-E circuit for WPT applications. Equations for the series-tuned secondary coil WPT system are presented, as well as two different design procedures for the parallel-tuned secondary coil. The derived equations have been... 

Pole Side Impact Tes is one out of three crash tests described by Euro NCAP standard for star rating of a vehicle and is required for assessing the Adult Occupant Protection. In this paper the goal is to determine the crashworthiness of side doors and B pillar in a Pole Side Impact Test based on Euro New Car Assessment Program (Euro-NCAP) using computer and simulation method. In this matter, a vehicle model has been prepared and meshed using Hypermesh and CATIA. The velocity of 29 km/h has been assigned to the vehicle which was on top of a cart while the pole has been assigned as a rigid static object based on Euro NCAP requirements specifically. Results show that different amounts of energy... 

To assess a car under the Euro New Car Assessment Program (Euro-NCAP), Adult Occupant Protection is one out of three parameters which need to be calculated with a weight factor of 50% while the other parameters, Child Occupant Protection and Pedestrian Occupant Protection, have a weight factor of 20%. The Pole Side Impact Test, beside two other tests, Side and Front Impact, is also required to calculate the Adult Occupant Protection. It shows how important the Pole Side Impact Test is and what an effective role it has in the car rating assessment. In this paper, the objective is to evaluate the effect of thickness on the energy absorbed by the side doors and the B pillar and its... 

In Euro NCAP standard, adult protection is one of the most important rating scores with 50% weight factor while child protection and pedestrian protection are accounted into consideration with 20% weight factor. For adult protection testing, three tests are required to perform: (1) side impact, (2) pole impact, (3) front impact. In the side impact test, dummy's head, chest, shoulder, thorax, ribs, abdomen, pelvic and femur must be studied to evaluate the rating score. Crashworthiness of a car during side impact can describe the score rated for that car. In this paper the goal is to determine the crashworthiness of side doors and B-pillar in side impact crash est by simulation using LS DYNA...