Sharif Digital Repository

This article describes an automatic reactor power control system for VVER-1000 reactor and reports simulation analysis results for a typical daily load follow operation. The associated reactor control algorithm is called `mode G' that uses a heavy-worth bank (H-bank) dedicated to axial power shape control and the light-gray banks (G-banks) for reactor power change and reactivity compensation. The simulation results for daily load follow operation in three burnup states of first cycle illustrate that the load follow capability of VVER-1000 reactors using this algorithm will be improved  

Background and objective Image registration is one of the fundamental and essential tasks for medical imaging and remote sensing applications. One of the most common challenges in this area is the presence of complex spatially varying intensity distortion in the images. The widely used similarity metrics, such as MI (Mutual Information), CC (Correlation Coefficient), SSD (Sum of Square Difference), SAD (Sum of Absolute Difference) and CR (Correlation Ratio), are not robust against this kind of distortion because stationarity assumption and the pixel-wise independence cannot be obeyed and captured by these metrics. Methods In this paper, we propose a new intensity-based method for... 

The adhesion of hydroxyapatite (HA) as a coating for the AZ91 magnesium alloy substrate can be improved by using the sputtering method and an intermediate layer, such as ZrN. In this study, HA coatings were applied on ZrN intermediate layers at a temperature of 300 °C for 180, 240, 300, 360, and 420 min by ion beam sputtering. A profilometer device was used to study the HA coating thickness, which changed from 2 μm for the 180-min deposition to 4.7 μm for 420-min deposition. The grazing incidence X-ray diffraction analysis method and the Williamson–Hall analysis were used for structural investigation. As the deposition time increased, the crystalline size increased from 50 nm to 690 nm.... 

We present a methodology for characterization and an approach for computing the solutions of fuzzy linear systems with LR fuzzy variables. As solutions, notions of exact and approximate solutions are considered. We transform the fuzzy linear system into a corresponding linear crisp system and a constrained least squares problem. If the corresponding crisp system is incompatible, then the fuzzy LR system lacks exact solutions. We show that the fuzzy LR system has an exact solution if and only if the corresponding crisp system is compatible (has a solution) and the solution of the corresponding least squares problem is equal to zero. In this case, the exact solution is determined by the... 

The formation of macroporous bioactive hydroxyapatite(HA) coatings using polytetrafluoroethylene(PTFE) particles were studied. The porous HA coatings were prepared onto a pure titanium substrate by electrophoretic deposition(EPD) at 120 V for 1.5 min using ethanol suspensions mixture of HA (500 nm in size) and PTFE (1-3 μm in size) particles. Subsequently, the composite coatings obtained by EPD were heated at 900 °C for 60 min to disintegrate the organic PTFE particles and sinter the inorganic HA particles. The calcinations of the PTFE led to the formation of porosity in the HA coating. These results demonstrate a new method for creating porous HA coatings on titanium. © 2006 Elsevier B.V.... 

Porous surface on titanium induces apatite formation in simulated body fluid (SBF). This work shows alkaline, acid and polishing treatment, which lead to create apatite coating. Specimens were soaked in 5 M solution of NaOH, 85% HCl-6% HF-9% H3PO4 and 2% HF-4% HNO3-94% H2O. Also many samples were polished with sandpaper. Specimens treated under the above conditions were soaked in simulated body fluid (SBF) for 5 days. Apatite formed within 5 days. The evaluation of Ca/P ratio of samples were made by EDAX analysis to get information of the Ca/P ratio. The values obtained for the apatite were in the range of 1.55, which is near to the stoichiometric value of apatite, for the sample, which was... 

Hydroxyapatite (HA) coatings were deposited on commercially pure titanium plates using a hydrothermal-electrochemical deposition method in an electrolyte containing calcium and phosphate ions. The deposition conditions used in this study were the followings: electrolyte temperature (33-80 °C), current density (1-8 mA/cm2), and deposition time (10-120 min). Needle-like and granular crystals of apatite coating were created with different concentrations of calcium (0.0021-0.042 M) and phosphate (0.00125-0.025 M) salts. The size of HA crystals of the coating was considerably changed with different concentration of calcium and phosphate salts, temperature of the electrolyte, and deposition time.... 

Using multiple antennas at the transmit and receive sides of a passive radar brings both the benefits of MIMO radar and passive radar. However one of the obstacles arisen in such configuration is the receive antennas placement in proper positions so that the radar performance is improved. Here we just consider the case of positioning one receiver among multiple illuminators of opportunity. Indeed it is a start for the solution of optimizing the geometry of the multiple receivers in a passive radar  

SbCl3 supported on montmorillonite K-10 is an efficient catalyst for the ring opening of epoxides with aromatic amines under solvent-free conditions and microwave irradiation to give the corresponding b-amino alcohols in high yields with high regioselectivity  

In this paper, we consider an integrated sensing and communication (ISAC) system with wireless power transfer (WPT) where an unmanned aerial vehicle (UAV)-based radar serves a group of energy-limited communication users in addition to its sensing functionality. In this architecture, the radar senses the environment in phase 1 (namely sensing phase) and mean-while, the communications users (nodes) harvest and store the energy from the radar transmit signal. The stored energy is then used for information transmission from the nodes to UAV in phase 2, i.e., uplink phase. Performance of the radar system depends on the transmit signal as well as the receive filter; the energy of the transmit... 

One of the important obstacles in MIMO (Multiple Input Multiple Output) radars is the issue of designing proper transmit signals. Indeed, the capability of signal design is a significant advantage in MIMO radars, through which, the system can achieve much better performance. Many different aspects of this performance improvement have been considered yet, and the transmit signals have been designed to attain such goal, e.g., getting higher SNR or better detector's performance at the receiver. However, an important tool for evaluating the radar's performance is its ambiguity function. In this paper, we consider the problem of transmit signal design, in order to optimize the ambiguity function... 

Two gains play key roles in recently developed MIMO wireless communication systems: "spatial diversity" gain and "spatial multiplexing" gain. The diversity gain refers to the capability to decrease the error rate of the MIMO channel, while the multiplexing gain implicitly refers to the amount of increase in the capacity of the MIMO channel. It has been shown that there is a fundamental tradeoff between these two types of gains, meaning interplay between increasing reliability (via an increase in the diversity gain) and increasing data rate (via an increase in the multiplexing gain). On the other hand, recently, MIMO radars have attracted much attention for their superior ability to enhance... 

It is a well known fact that using multiple antennas at transmit and receive sides improves the detection performance. However, in such multiple-input multiple-output (MIMO) configuration, proper positioning of transmitters and receivers is a big challenge that can have significant influence on the performance of the overall system. In addition, determining the power of each transmitter under a total power constraint is a problem that should be solved in order to enhance the performance and coverage of such a system. In this paper, we design the Neyman-Pearson detector under the Rayleigh scatter model and use it to introduce a criterion for the antenna placement at both transmit and receive... 

There has been much interest, recently, towards exploiting the Multiple-Input Multiple-Output (MIMO) technique in radar. It is shown that using multiple antennas at transmit and receive sides can improve the performance of the system. However, in order to analyze the system's performance, its ambiguity function, i.e. the ambiguity function of a MIMO radar, is needed to be defined. In this paper, beginning from the information theoretic definitions, we derive such function, specifically for a MIMO radar with widely separated antennas  

By combining the two ideas of MIMO (Multiple Input Multiple Output) and PCL (Passive Coherent Location) in radar, one can achieve the advantages of both recently developed techniques simultaneously. While using multiple antennas at the receive side provides a spatial diversity of the object to be detected, using multiple illuminators of opportunity, most importantly, makes the radar covert to the interceptors. One obstacle in such MIMO configuration is choosing the positions of the receive antennas. In this paper, after analyzing the Neyman-Pearson detector for the DVB-T based PCL, we introduce the probability of missed detection as a criterion to place the receive antenna. Here, we only...