Sharif Digital Repository

In this study, bioglasses in SiO2-CaO-MgO system were synthesized through sol-gel method and the effect of silica and magnesia contents on in-vitro bioactivity of the bioglasses were investigated. XRD patterns showed an amorphous structure after heat treatment at 600°C for 2 h for all glasses and also indicated that after immersion in SBF, apatite particles precipitated on glass surfaces and the rate of apatite formation decreased with increasing Mg/Ca ratio. On the other hand, the apatite formation rate was enhanced with increasing the silica content. Furthermore, magnesia contents increased the compressive strength of the samples. According to SEM, higher Mg/Ca ratio led to increase in... 

The aim of this work is to investigate thermal stability of expanded martensite. For this purpose, two martensitic stainless steels, PH 17-4 and 13-8Mo, were low temperature gas carburized. After heat treatment, it was found out that thermal stability of expanded layer of PH 17-4 is higher than that of PH 13-8Mo. Auger Electron Spectroscopy and microhardness machines were used to investigate carbon concentration and hardness of samples, respectively. X-ray diffraction was done to study crystal structures of samples before and after heat treatment  

The out-of-pack cementation method was applied to coat the Nickel-based super alloy IN738LC with Si-modified aluminide. Different mixtures of the pack containing pure Al, Si, alumina powders as an inert filler, and NH4Cl as a halide salt activator were used for co-deposition at 950 and 1,050°C. The results showed although the amount of subhalide vapour pressures of Al and Si were equal at 1,050°C, Al atoms diffused only after Si atoms had been deposited. Before heat treatment, the coating thickness formed by the pack containing 2.3 wt.% Al was 6 μm more than that containing 3.5 wt.% Al. After heat treatment, thickening coatings formed within the pack containing 2.3 wt.% Al was less than that... 

Pd doped WO3 fibers were synthesized by electro-spinning. The sol gel method was employed to prepare peroxopolytungstic acid (P-PTA). Palladium chloride and Polyvinyl pyrrolidone (PVP) was dissolved in the sol Pd:WO3 = 10% molar ratio. The prepared sol was loaded into a syringe connected to a high voltage of 18.3 kV and electrospun fibers were collected on the alumina substrates. Scanning electron microscope (SEM), X-ray powder diffraction (XRD) and X-ray photoelectron spectroscopy (XPS) techniques were used to analyze the crystal structure and chemical composition of the fibers after heat treatment at 500 °C. Resistance-sensing measurements exhibited a sensitivity of about 30 at 500 ppm... 

Carbide morphologies of white cast iron containing 22% Cr and 10-12% tungsten with different carbon contents (2.34-3.20. wt.%) were investigated. Results indicated that for the as-cast alloys with no heat treatments, the addition of carbon changes the morphology of carbides during air-cooling in the presence of tungsten. Light microscopy analysis revealed that for an alloy with 2.3. wt% carbon, chromium carbides possess coarse gray appearance (GA). Increasing the carbon content reduced the coarse GA zones volume fraction while a finer GA zones emerged. The coexistence of coarse and fine GA phases came to an end at 2.8. wt% carbon, at which only fine GA zones spread throughout the chromium... 

In this research, 1050 aluminum sheets in the conditions of annealed and severely deformed by 2 passes of constrained groove pressing (CGP) process were used. Two passes of friction stir processing (FSP) were applied on the specimens. Also, another CGPed specimen was processed by 2 passes of FSP using SiC nanoparticles. The samples were then heat treated to study thermal stability of base metal, heat affected zone (HAZ), thermo-mechanically affected zone (TMAZ), and stir zone (SZ). Microstructure examinations revealed that the annealed base metal was relatively stable upon heating even up to 400. °C and a little grain growth was evident. On the other hand, the CGPed base metal was fairly... 

In this study, the effects of simultaneous co-deposition of polytetrafluoroethylene (PTFE) and MoS 2 particles on tribological properties of electroless nickel (EN) coating were studied. The influences of specimen orientation and heat treatment on EN-PTFE-MoS 2 composite coatings were also investigated. Scanning electron microscopy was used to study the morphology of coatings and the distributions of the lubricant particles in the deposits. Chemical analyses of coatings were done by electron dispersive spectrometry. The phases of the coatings were identified by X-ray diffraction utilizing CuKα radiation. Wear and friction properties of the coatings were also determined by pin-on-disk wear... 

In this study, the crystallisation of nano hydroxyapatite (HA) films on stainless steel 316L was studied. The film was prepared by sol-gel technique. The process was started with preparation of an HA sol. After aging of the sol at room temperature, a stainless steel 316L substrate was dip coated and then was heat treated from 350 to 450°C at different periods of time in air. The crystallisation behaviour and the transformation-temperature-time diagram of HA films were achieved and analysed using the avrami equation. The results showed that the crystallisation of HA began at 250°C and was increased up to 450°C. The obtained HA film showed a nanostructure character with a suitable crystalinity... 

In this study, the surface morphology of Ni–P–SiO2 composite coating was investigated by field emission scanning electron microscopy (FESEM). The amount of SiO2 in the coating was examined by energy dispersive analysis of X-ray (EDX) and the Corrosion behavior of coating was evaluated by electrochemical impedance spectroscopy (EIS) and polarization techniques, showing the corrosion resistance of Ni–P–SiO2 diminished after heat treatment. The results showed that in the coating with 12.5 g/L SiO2, the coating hardness enhanced from 453VH to 980 VH before and after heat treatment. Furthermore, the wear behavior of the coating was analyzed before and after heat treatment  

The friction stir welding of AA2024-T6 to AA6061-T6 plates with a 4 mm thickness has been studied at constant traverse and rotational speeds of 1000 rpm and 100 mm/min, respectively. The position of alloys and the effects of precipitation hardening heat treatment in retreating and advancing side in the friction stir welding were analyzed. The tool with taper threaded pin was used for welding. Macro and microstructural analysis were investigated by using Optical and Field Emission-Scanning Electron Microscopes (FE-SEM) to check out the welded joints. Micro-hardness and Tensile tests were also done to study mechanical attributes of the joints. Microstructural analysis revealed some grain... 

This study investigated the effect of intercritical heat treatment temperature on the tensile properties, work hardening and corrosion resistance of dual phase steel. Ferrite-martensite dual phase steel with different martensite volume fractions were obtained after heat treatment at different intercritical temperatures. Microstructure, mechanical properties of steel were measured and the corrosion resistance was evaluated via polarization test. Tensile strength of the specimens increased by increasing the martensite volume fraction up to 48.2%. Further increase in martensite volume fraction led to decrease in tensile strength. Work hardening behavior analyzing showed that in DP steel with... 

This study aimed to prepare nanoporous anodic alumina on AA3003-H14 aluminum alloy using a mild anodization process with minimal working voltage and treatment time. The microstructural features, mechanical properties, and tribocorrosion behavior of the coatings were assessed to determine the optimum conditions for the fabrication of nanoporous anodic alumina on AA3003-H14 alloy. The microstructural analysis showed both uniform and nonuniform pore nucleations during anodization in H2SO4/C2H2O4, H2SO4/H2CrO4, and EG/H2O/NH4F electrolytes, where the optimal nanoporous structure with an average thickness, porosity, pore diameter, and interpore distance of 382 nm, 19%, 16 nm, and 35 nm,... 

Aluminum-Al3Ti reinforced MMCs were produced with a large amount (up to ~30 vol%) of Al3Ti phase via mechanical alloying, hot extrusion and heat treatment (as a supplementary process) of the Al–Ti elemental powder mixture, respectively. Samples in each stage were studied precise and comprehensive by field emission electron microscope, energy dispersive spectroscopy, X-ray diffraction, differential scanning calorimetry, densitometry, macro and micssro hardness, nanoindentation and tensile tests. The results indicated that after 4-h vibratory milling, the aluminum crystallite size reached 63 nm and Al3Ti phase formed in powder mixture. After hot extrusion, the volume percentage of Al3Ti... 

A simple method for synthesis of W17O47 nanothick plates by annealing sol-gel-deposited tungsten oxide thin films on soda lime substrate has been reported. After heat treatment of the dried thin films at 700 °C in N2 ambient for 60 min, W17O47 nanothick plates with [100] orientation were obtained. The synthesized product was characterized and analyzed by, X-ray diffraction (XRD), SEM, XPS and ultraviolet-visible spectrophotometery. According to SEM observations, nanothick plates grew with random orientations on the surface. In addition, it was observed that some of the nanothick plates were constituted from several nanosheets. XRD analysis determined that the nanothick plates were mainly...