Sharif Digital Repository

In this work, a porous and flexible three-dimensional (3D) nickel/gold nanoparticle electrode (NiF/AuNPs) is presented as an efficient electrocatalyst for ethanol oxidation in alkaline media. The 3D nanocomposite electrode consists of interconnected porous nickel foam (NiF) with large pores (500±200 μm diameter) surrounded by interconnected struts (∼100 μm) that are decorated with gold nanoparticles (AuNPs, 37±8 nm) through in-situ electrochemical deposition. The catalytic performance of the 3D electrode was evaluated by different electrochemical methods. An enhancement in the performance (about 253 %) and a remarkable decline in onset potential (about ∼0.63 V) in comparison with pristine... 

Today, Li-ion batteries (LIBs) are the most common rechargeable batteries used in electronic devices. SnO2 with theoretical specific capacity of 782 mAh/g is among the best anode materials for LIBs. In this report, Threedimensional SnO2 nanowires (NWs) on carbon nanotube (CNT) thin film (SnO2 / CNT) is fabricated using a combination of vacuum filtration and thermal evaporation techniques. The resulting 3D heterostructure SnO2/CNT was characterized by X-ray diffraction, transmission electron microscopy (TEM) and scanning electron microscopy (SEM). This fabricated SnO2/CNT electrode has been tested as a flexible and binderfree anode for LIB, which exhibits high initial discharge/charge... 

Microbial fuel cells (MFCs) represent a new method for simultaneous wastewater treatment and biological electricity generation. In this study, petrochemical wastewater with 8000 mg/l of chemical oxygen demand was examined in a membrane-less single chamber MFC. Effects of wastewater concentration as substrate for microbial oxidation, and anode material (stainless steel or carbon brush) were investigated as designing parameters  

Titanium nitride/graphene nanocomposite as an anode material of lithium ion batteries has been fabricated through the reaction of TiCl4 and NaN3 in supercritical benzene medium followed by ammonia treating at 1000 °C for 10 h. The synthesized TiN/G nanocomposite depicts rate-dependent behavior in such a way that it shows specific capacity of 115 mAh g−1 when is cycled at higher rate (1.6 C) while it shows 76 mAh g−1 when is cycled initially at lower rate (0.2 C) and is subsequently subjected to higher rate (1.6 C). Moreover, TiN/G anode demonstrates capacity retention of 112%, 100%, and 70% after 250 cycles at charge/discharge rates of 1.6, 0.7, and 0.2 C, respectively. This unusual behavior... 

Here, cobalt oxide nanostructures synthesized on vertically aligned copper oxide nanowires (NWs) have been investigated as a possible anode material for Lithium-ion batteries (LIBs). Copper oxide NWs were formed by thermal oxidation of electrochemically deposited copper on the stainless steel mesh substrate. The process used allows the formation of highly dense copper oxide NWs with excellent adhesion to the conductive current collector substrate. A simple hydrothermal method was implemented for the deposition of cobalt oxide nanostructures on the copper oxide NWs. The as-prepared binder-free copper oxide@cobalt oxide NWs electrode exhibits a high initial specific capacity of 460 mAh g-1 at... 

SnO2 is considered as one of the high specific capacity anode materials for Lithium-ion batteries. However, the low electrical conductivity of SnO2 limits its applications. This manuscript reports a simple and efficient approach for the synthesis of Sb-doped SnO2 nanowires (NWs) core and carbon shell structure which effectively enhances the electrical conductivity and electrochemical performance of SnO2 nanostructures. Sb doping was performed during the vapor-liquid-solid synthesis of SnO2 NWs in a horizontal furnace. Subsequently, carbon nanolayer was coated on the NWs using the DC Plasma Enhanced Chemical Vapor Deposition approach. The carbon-coated shell improves the Solid-Electrolyte...