Sharif Digital Repository

Maritime structures such as waterfronts, offshore platforms and hulks all face different maritime sediments. There are different methods to prevent the growth of organic and non-organic material on humid surfaces, but the utilization of antifouling paints has had the most efficiency. The growth of these maritime pollutions has been stopped on hulks by the antifouling paints. Ever since the nineteenth century, antifouling paints have been utilized with different mechanisms and the most important one was the TBT self-polishing paints that were banned in 2003 by the International Marine Organization (IMO) because of the high pollution it creates in the environment. There have been many efforts... 

In order to compare the frictional resistance of three kinds of ship’s hull coatings (foul release, SPC copper, SPC TBT) in the unfouled conditions, the numerical studies have been made. Simulations have been carried out for different Reynolds numbers in the range of 2.85 × 106-5.5 × 106 based on the plate length and flow velocity. Antifouling coatings have larger mean roughness than foul release. The results have indicated that frictional resistance coefficient of foul release test plate is lower than SPC copper and SPC TBT test plates. The total resistance obtained by computational fluid dynamics has been compared with the experimental data and its good agreement has proven the ability of... 

This study concentrates on fabrication of low-cost antifouling membranes by incorporation of alumina in PVC membranes for membrane bioreactor (MBR). PVC based membranes were prepared via phase inversion method at different alumina contents. Pure water flux through the membranes and its antifouling properties in MBR setup at operating pressure of −0.4 bar were studied. The effects of the alumina on the morphology and physical properties of the membranes were investigated by scanning electron microscopy (SEM), atomic force microscopy (AFM), contact angle, pore size, viscosity, porosity, and mechanical properties. The results showed that the membrane with 3 wt% alumina exhibited excellent... 

Recently, membrane fouling has been one of the most important issues in the field of membrane technology. In this regard, TiO2 nanoparticles blended with polymeric membranes have shown to improve fouling performance. In this study, a new PVDF/PAN/TiO2 ultrafiltration blend membrane was prepared via phase inversion by dispersing TiO2 nanoparticles in the PVDF/PAN casting solutions. The effect of different concentrations of TiO2 on the characteristics of membranes (i.e., morphology, hydrophilicity, permeation performance, and antifouling properties) was investigated. Results of scanning electron microscopy analysis showed the finger-like pores and macrovoids decrease due to the presence of... 

The current study investigates the effect of polyacrylonitrile (PAN) addition on morphology and antifouling properties of poly(vinyl chloride) (PVC) asymmetric flat ultrafiltration (UF) membranes. The membranes are prepared via phase inversion method induced by immersion precipitation at different PVC/PAN blending ratio up to 40 wt% PAN. Also, membranes with blending ratio of PVC/ PAN:70/30, which showed the highest water flux and flux recovery ratio, were used for membrane preparation with 4 wt% of Polyethylene glycol (PEG) addition in four different molecular weight, 600 Da, 1,000 Da, 6,000 Da and 20,000 Da, which was used as pore former and hydrophilic polymeric additive. The performance... 

A new multifunctional filtration membrane was prepared by twofold advantages of conventional polymeric-membrane as the supporting layer and magneto-plasmonic Ag-doped ZnO@Fe3O4/MWCNTs nanocomposite as the functional layer. Poly acrylic acid (PAA)-modified polyamide (PA) discs (PAA-PA) were applied to increase the hydrophilicity of prepared membrane and X-Ray diffraction (XRD) and scanning electron microscopy (SEM) techniques were used for characterization. The grafting yield of PAA in the pores and on the surface of PA was 17 wt.% and weigh difference between PAA-PA membrane before and after modifying with the photocatalyst was 8.7 mg. The amount of photocatalyst loading in the prepared... 

In this study, modification of polyvinyl chloride (PVC) ultrafiltration membranes with zinc oxide (ZnO) nanoparticle addition was taken into consideration. The ZnO at five different weights was added to the polymeric solution, and the membranes were fabricated by the phase inversion method using water as a nonsolvent and PEG 6 kDa as a pore former additive. The results showed that the pure water flux of the modified membranes increased up to 3 wt% ZnO addition, which was the optimized amount of the nanoparticle addition in this study. Also, at 3 wt% ZnO addition, flux recovery ratio reached from 69% to above 90%, indicated that the nanocomposite membranes were less susceptible to be fouled.... 

In this study, a hydrophilic metal-organic framework (MOF) was applied to improve the performance of a cellulosic membrane for forward osmosis (FO) desalination application. The characterization results confirmed that the MOF particles existed within the matrix of the modified membrane. The MOF loading led to adjustment of the membranes in terms of overall porosity, pore inter-connectivity and hydrophilicity. These features caused an improvement in the pure water permeability (72%) and reduce the structural parameter of the modified membrane to 136 μm. The FO water flux of the modified membrane enhanced by about 180% compared to an unmodified membrane, without decreasing its selectivity. FO... 

In the present work, ultrafiltration membranes were prepared using emulsion polyvinyl chloride (EPVC) with the addition of various concentrations of polyethylene glycol (PEG) to investigate the morphological structure and separation properties. The effects of polymer concentration, coagulation bath temperature (CBT), and PEG (6 kDa) concentrations—a pore former hydrophilic additive—were studied. Through the phase inversion, the membranes—which were induced by immersion precipitation in a water coagulation bath—were fabricated through dissolving EPVC in N-methyl-pyrrolidinone, a polymer solvent. Morphological features of the membranes were characterized through scanning electron microscopy,... 

In this research, cellulose acetate butyrate (CAB) electrospun nanofiber membrane (ENM) was prepared by electrospinning method in order to separate the contaminants of an industrial wastewater. The influence of various electrospinning parameters on morphology and average fiber diameter of the membranes were investigated by scanning electron microscopy and image analysis. The permeability of the membranes was evaluated by measuring pure water flux. In order to investigate the performance of the prepared membranes for tomato wastewater treatment, the rejection of the pollution indices and flux were determined. The results demonstrated the potential of using CAB nanofiber membrane for... 

In this study, two new composite membranes with antifouling and anti-biofouling properties were prepared through the modification of commercial polyamide (PA) discs using combination of in-situ polymerization of polyacrylic acid (PAA) and grafting of two synthesized bi-plasmonic Au-Ag and Ag-Au photocatalysts. The synthesis and characterization of the photocatalysts in batch mode were discussed in details as primary studies. Two intense 405-nm and 532-nm lasers for Ag-Au and Au-Ag photocatalysts, respectively and a solar-simulated xenon lamp for both photocatalysts were applied for photodegradation studies and the results were compared. In addition, the effect of other parameters such as... 

We introduce highly antifouling Polymer-Nanoparticle-Nanoparticle/Polymer (PNNP) hybrid membranes as multi-functional materials for versatile purification of wastewater. Nitrogen-rich polyethylenimine (PEI)-functionalized halloysite nanotube (HNT-SiO2-PEI) nanoparticles were developed and embedded in polyvinyl chloride (PVC) membranes for protein and dye filtration. Bulk and surface characteristics of the resulting HNT-SiO2-PEI nanocomposites were determined using Fourier-transform infrared spectroscopy (FTIR), X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), transmission electron microscopy (TEM), and thermogravimetric analysis (TGA). Moreover, microstructure and... 

A new photocatalytic filtration membrane was prepared by grafting of Ag–Au bi-plasmonic shell-on TiO2@Fe3O4 nanoparticles as a magnetically-separable heterogeneous photocatalyst to a poly acrylic acid-modified cellulose acetate membrane for decomposition and removal of methyl orange as a model pollutant from textile wastewater samples. Eight photocatalysts including five Au NPs-modified TiO2@Fe3O4 NPs and three Ag-Au bi-plasmonic NPs-decorated TiO2@Fe3O4 NPs with different shell thickness were synthesized and characterized by TEM, UV–vis, and SEM techniques and their photocatalytic activity was assessed using two radiation sources. After selection of optimum photocatalyst and modification of... 

In this study, maleic anhydride grafted polypropylene microporous flat-sheet membranes were prepared via a thermally induced phase separation method with a mixture of dibutyl phthalate and dioctyl phthalate as a diluent. The effects of the polymer composition and coagulation bath temperature on the morphology and performance of the fabricated membranes were investigated. The hydrophilicity results of the membranes demonstrated that membrane modification reduced the water contact angle by about 45°, whereas the pure water flux was enhanced about four times. The antifouling behavior of the fabricated membranes was also investigated in a membrane bioreactor. The results show that the pure water... 

Novel montmorillonite (Mt) chitosan/poly(vinyl alcohol) (PVA) nanocomposite electrospun nanofibrous membranes (ENM) were prepared and utilized for the treatment of colored wastewater. The Mt. with different mass percentages (0, 1.0, 2.0 and 3.0 mass%) was added to the membrane structure, and its effect on morphology, pore size, porosity, mechanical strength, and permeation properties of ENM were investigated. The fabricated membranes were used as affinity membranes for dye removal with ultrafast permeating adsorption. The results showed that incorporating Mt. as a reinforcing agent improved the nanocomposite ENM resistance to compaction. Young's modulus for the prepared membranes increased... 

The purpose of this research is to explain the surface modification of fabricated polyamide reverse osmosis (RO) membranes using UV-initiated graft polymerization at different irradiation times (15, 30, 60, and 90 s) and various acrylamide concentrations (10, 20, and 30 g L−1). Also, coating of membranes surface with various concentrations of TiO2 nanoparticles (10, 20, 30, and 50 ppm) followed by the same UV irradiation times was investigated. After that, the membranes modification was done by grafting of acrylamide blended with TiO2 nanoparticles via UV irradiation. The characterization of membranes surface properties and their performance were systematically carried out. The results... 

The current article discusses some unprecedented information about the improvement in forward osmosis (FO) performance of polyethersulfone/polyamide (PES/PA) membranes, mainly focused on water flux and selectivity along with resistance to fouling phenomenon; which itself is brought in by the introduction of pre-modified zeolitic imidazolate framework-8 MOF nanoparticles. An investigation has been conducted on ZIF-8 nanoparticles surface with hydrophilicity feature to evaluate their potential for utilization in active polyamide layer of FO membranes for the first time, free from any decrease in water flux value (when hydrophobic ZIF-8 is exploited solely) and selectivity (when mSiO2 with... 

Efficient utilization of solar energy as the cleanest and most plentiful natural resource for drinking water is a water is as sustianble and environmental friendly approach to obviate long-standing water scarcity. Carbon-based photothermal absorbers due to broadband light absorption are very interesting in interfacial solar steam generation systems. Herein, we investigate the convenient application of reduced graphene oxide (rGO) nanosheets with carbon black (CB) nanoparticles on the cotton fabric as a flexible texture-based photothermal absorber. Polyurethane (PU) as a self-floating insulator foam was selected to manage the energy loss and preserve light converted to heat on the fabric... 

In the current study, the prospect improvements on desalination and anti-fouling performance of polyamide (PA)-based TFN membranes modified with MIL-53-NH-Asp have been investigated. MIL-53-NH2 nanoparticles (NPs) have been treated through a single-step post-synthesis modification reaction to enhance the hydrophilicity feature and compatibility with the PA layer. Various concentrations of synthesized NPs were dispersed in an aqueous phase consisting m-phenylenediamine and 2,6-diaminopyridine monomers for incorporation in the PA rejection layer. Analysis data of fabricated membranes provide evidence of changes in their physico-chemical properties after NPs incorporation. In comparison with...