Sharif Digital Repository

A cyclic forward-backward extrusion (CFBE) process was used as a severe plastic deformation (SPD) technique to produce ultrafine-grained aluminum rods. Yield strength and tensile strength of the specimens increased by increasing the number of CFBE cycles, while elongation to break decreased due to an increase in the grain refinement and microhardness. According to transmission electron microscopy (TEM) and electron backscatter diffraction (EBSD) results, the average grain size was reduced from 120 μm to 315 nm after only 3 cycles of CFBE  

Equal channel angular pressing is an effective technique to control the texture and microstructure of metals and alloys. Texture and microstructure of an Al-7075 alloy subjected to repetitive equal channel angular pressing through a 90° die were evaluated by X-ray diffractometer and orientation imaging microscopy. It is observed that processing through different routes leads to different types of textures, in both qualitative and quantitative senses. The texture calculation by Labotex software reveals that texture strengthens after the first pass and weakens by progressing ECAP process up to 4 passes. Microstructure investigations show that after 4 passes of equal channel angular pressing... 

Electric field enhanced approach has been used to synthesize different copper hydroxide morphologies as high-performance supercapacitors electrode materials. Employing this efficient, simple and low cost method, various shapes such as rod, flower and cube with an average grain size of 30nm to 1μm were obtained on the copper substrate. The results revealed that applied electric field considerably accelerates the formation time of nanostructures from several days to close to 1min, where some of the desired nanostructures were obtained even in 1s. The electrochemical properties of different morphologies were compared using cyclic voltammograms and charge/discharge tests and electrochemical... 

Travel speeds between 25–300 mm/min and tool rotational speeds of 800 and 1250 rpm were employed for this study. The microstructure, mechanical properties and fracture surfaces of the joints were studied. Underwater environment and an increase in travel speed significantly increase the precipitates’ volume fraction, reduce the average grain and precipitate sizes of the weld nugget zones. A critical travel speed of 150 mm/min is attained in underwater welds beyond which the average grain sizes remain relatively the same. Average grain and precipitate sizes have linear relationships with the tool rotational and travel speed ratio. Optimum weld strengths of 396 and 360 MPa were obtained in the... 

Surface integrity is one of the important parameters affecting the quality and functionality of mechanical components. This paper presents an investigation on effect of drilling parameter on the surface integrity of Inconel 718 through a combination of experimental and simulation works. The machining responses that are determined through the experimental work include microhardness, microstructure changes, and surface roughness. The average grain size of the microstructure of the workpiece is estimated by using a simulation model. The experimental and simulation results show that higher spindle speed facilitates the formation of white layer near the machined surface and decreases the average... 

The BaCe0.9Y0.1O3-δ (BCY) perovskite membrane was successfully synthesized by liquid citrate method. The phase structure of the powder was characterized by X-ray diffraction (XRD). Scanning electron microscopy (SEM) was used to characterize microstructures of the membrane sintered under various conditions. Sintering temperatures and dwell time during sintering influence the final microstructure of the ceramic. Results showed that increasing sintering temperature resulted in a dense membrane with clear grains. An increase of dwell time was favorable to produce membranes with larger grains in the sintered ceramics. A density of 5.87 g/cm3 was reached for the membrane after sintering at 1200 °C... 

The morphological manipulation and structural characterisation of TiO 2-MgO binary system by an aqueous particulate sol-gel route were reported. Different crystal structures including pure MgTiO 3, mixtures of MgTiO 3 and TiO 2 and mixtures of MgTiO 3 and Mg 2TiO 4 were tailored by controlling Mg:Ti molar ratio and annealing temperatures as the processing parameters. X-ray diffraction (XRD) and Fourier transform infrared spectroscopy (FTIR) revealed that all compounds crystallised at the low temperature of 500 °C. Furthermore, it was found that the average crystallite size of the compounds depends upon the Mg:Ti molar ratio as well as the annealing temperature, being in the range 3-5 nm at... 

The effect of particle size, lattice strain and crystallite size on the hydrogen desorption properties of nanocrystalline magnesium hydride powder was investigated. Commercial MgH2 powder was milled in a Spex 8000M up to 16 h and its structural evolution and desorption characteristics at different time intervals were examined using various analytical techniques. At the early stage of milling, the formation of metastable γ-MgH2 phase was noticed. While the crystallite size gradually decreased to 12 nm with increasing the milling time, the accumulated lattice strain gained a maximum value of 0·9% after 4 h milling. The highest drop in the desorption temperature (∼100°C) was attained at the... 

Friction stir processing (FSP) was used to fabricate AZ31/Al2O3 nanocomposites for surface applications. The effects of probe profile, rotational speed and the number of FSP passes on nanoparticle distribution and matrix microstructure were studied. The grain refinement of matrix and improved distribution of nanoparticles were obtained after each FSP pass. By increasing the rotational speed, as a result of greater heat input, grain size of the base alloy increased and simultaneously more shattering effect of rotation, cause a better nanoparticle distribution. The average grain size of matrix of the composites was in the range of 1-5μm and the microhardness of them was 85-92Hv  

Nanostructured CoTiO3 thin films and powders were prepared by a straightforward aqueous particulate sol–gel route. Titanium(IV) isopropoxide and cobalt chloride were used as titanium and cobalt precursors, respectively. Also, hydroxypropyl cellulose was used as a polymeric fugitive agent in order to increase the specific surface area. The effect of Co:Ti molar ratio and annealing temperature were studied on the crystallization behavior and chemical properties of the products. X-ray diffraction and Fourier transform infrared spectroscopy revealed that the powders crystallized at the low annealing temperature of 300 °C for 1 h, containing anatase-TiO2,... 

The effects of thermal history on the microstructure and mechanical properties of a friction-stir-processed Al–Mg–TiO2 (3 vol.-%, 20 nm) nanocomposite were studied. It is shown that, with increases in peak temperature, a more uniform distribution of nanoparticles in the metal matrix, and a refined grain structure, are attained. Transmission electron microscopy indicated that the mechanism of grain refinement is influenced by the hard inclusions, changing from discontinuous to continuous dynamic recrystallisation. A fine-grained nanocomposite (average grain size of 3 µm) with a uniform distribution of nanoparticles is obtained after four fully-overlapping passes at 1200 rev min−1 and 100 mm... 

Two-step sintering (TSS) was applied to suppress the accelerated grain growth of sub-micron (∼150 nm) alumina powder. The application of an optimum TSS regime led to a remarkable decrease of grain size down to ∼500 nm; while the grain size of the full-dense structures produced by conventional sintering ranged between 1 and 2 μm. To find how important the temperatures at sintering steps might be, several TSS regimes were conducted. The results showed that the temperatures at both sintering steps play vital roles in densification and grain growth of the alumina compacts. Based on the results, the optimum regime consisted of heating the green bodies up to 1250 °C (first step) and then holding... 

The grain size dependence of flow stress in Cu-2.7 vol.%Al2O3 (15 nm) composite with a bimodal structure was studied. It is shown that the yield strength obeys the Hall-Petch equation when an appropriate value of average grain size based on the "rule of mixture" is employed. The Hall-Petch constants (σ0ε and kε) are proportional to strain as ε0.5. An equation for flow stress as a function of true strain and average grain size is proposed. The effect of alumina nanoparticles on the yield strength is shown to be related to large amounts of dislocations density. © 2009 Elsevier B.V. All rights reserved  

The influence of equal channel angular pressing (ECAP) on microstructure and mechanical behavior, as well as, strain aging during ECAP and post-ECAP of Mg-1.8Zn-0.7Si-0.4Ca biomedical alloy was examined. The alloy in solid solution heat-treated condition was processed by ECAP with route BC at 350 and 400 °C. The specimens ECAPed at 350 °C were aged at 125 and 150 °C for different times. The hardness and shear punch test results indicated that performing ECAP at 350 °C for 4 passes increases the hardness and shear strength of the alloy from 48 HV and 110 MPa to 71 HV and 188 MPa, respectively. It was revealed that the average grain size of the alloy decreases from 78 µm to about 3 µm after 4... 

Two-step sintering (TSS) was applied on nanocrystalline yttria tetragonal stabilized zirconia (3Y-TZP) to control the grain growth during the final stage of sintering. The process involves firing at a high temperature (T1) followed by rapid cooling to a lower temperature (T2) and soaking for a prolonged time (t). It is shown that for nanocrystalline 3Y-TZP (27 nm) the optimum processing condition is T1 = 1300 °C, T2 = 1150 °C and t = 30 h. Firing at T1 for 1 min yields 0.83 fractional density and renders pores unstable, leading to further densification at the lower temperature (T2) without remarkable grain growth. Consequently, full density zirconia ceramic with an average grain size of 110... 

Ce-doped ZnO nanocomposite thin films with Ce/Zn ratio fixed at optimum value (10 at.%) have been prepared via sol-gel method at different annealing temperatures varied from 180 to 500 °C. The synthesized samples were characterized employing atomic force microscopy (AFM), X-ray photoelectron spectroscopy (XPS), and X-ray diffraction (XRD) techniques. According to AFM analysis, the average grain size increased from about 70 nm to 150 nm by increasing the annealing temperature from 300 to 500 °C. Moreover, based on the XPS data analysis, it was found that three major metal ions namely Ce 3+, Ce4+, and Zn2+ coexist on the surface of the nanocomposite films. XPS data analysis also revealed that... 

The low temperature perovskite-type strontium titanate (SrTiO 3) thin films and powders with nanocrystalline and mesoporous structure were prepared by a straightforward particulate sol-gel route. The prepared sol had a narrow particle size distribution with hydrodynamic diameter of about 17 nm. X-ray diffraction (XRD) revealed that the synthesized powders had a perovskite-SrTiO 3 structure with preferable orientation growth along the (1 0 0) direction. TEM images showed that the average crystallite size of the powders annealed in the range 300-800°C was around 8 nm. FE-SEM analysis and AFM images revealed that the deposited thin films had mesoporous and nanocrystalline structure with the... 

TixSi1-xO2 compound thin-film systems were deposited by reactive RF magnetron co-sputtering technique. The effect of Ti concentration on the hydrophilicity of TixSi1-xO2 compound thin films was studied and it was shown that the films with Ti0.6Si0.4O2 composition possess the best hydrophilic property among all the grown samples. Surface ratio and average roughness of the thin films were measured by atomic force microscopy (AFM). Surface chemical states and stoichiometry of the films were determined by X-ray photoelectron spectroscopy (XPS). In addition, XPS revealed that the amount of Ti-O-Si bonds in nanometer depth from the surface of the Ti0.6Si0.4O2 films was the maximum, which resulted... 

In this study, the thermal cycles and the grain structure in the weld heat-affected zone (HAZ) are predicted. At the first stage, a combined heat transfer and fluid flow model is employed to assess the temperature fields during and after welding of 304 stainless steel and then, the evolution of grain structure is conducted using the predicted temperature distribution and an analytical model of grain growth. The grain sizes of the CGHAZ (coarse grain heat affected zone) achieved from the model are basically in agreement with those obtained from experimental measurement under different heat inputs in the range of 0.33-1.07 MJ/m. Both the experimental data and the calculated results show that... 

Highly stable, water-based barium titanate (BaTiO3) sols were developed by a low cost and straightforward sol-gel process. Nanocrystalline barium titanate thin films and powders with various Ba:Ti atomic ratios were produced from the aqueous sols. The prepared sols had a narrow particle size distribution in the range 21-23 nm and they were stable over 5 months. X-ray diffraction pattern revealed that powders contained mixture of hexagonal- or perovskite-BaTiO3 as well as a trace of Ba2Ti 13O22 and Ba4Ti2O27 phases, depending on annealing temperature and Ba:Ti atomic ratio. Highly pure barium titanate with cubic perovskite structure achieved with Ba:Ti = 50:50 atomic ratio at the high...