Sharif Digital Repository

The polycarbonate (PC)/thermoplastic polyurethane (TPU) blend membranes were prepared by phase inversion process applied to membrane bioreactor (MBR) to investigate the fouling characteristics. The impact of TPU and poly (vinylpyrrolidone) PVP concentration in polymer dopes on membrane structure, morphology, and performance were studied. The flat sheet fabricated membranes were characterized by scanning electron microscope (SEM), water contact angle (WCA), membrane surface roughness measurements and mechanical strength. The membrane performance was investigated at subcritical operating conditions. Pure water and critical flux through the fabricated membranes were measured for better... 

The current study investigates the effect of polyacrylonitrile (PAN) addition on morphology and antifouling properties of poly(vinyl chloride) (PVC) asymmetric flat ultrafiltration (UF) membranes. The membranes are prepared via phase inversion method induced by immersion precipitation at different PVC/PAN blending ratio up to 40 wt% PAN. Also, membranes with blending ratio of PVC/ PAN:70/30, which showed the highest water flux and flux recovery ratio, were used for membrane preparation with 4 wt% of Polyethylene glycol (PEG) addition in four different molecular weight, 600 Da, 1,000 Da, 6,000 Da and 20,000 Da, which was used as pore former and hydrophilic polymeric additive. The performance... 

Recently, membrane fouling has been one of the most important issues in the field of membrane technology. In this regard, TiO2 nanoparticles blended with polymeric membranes have shown to improve fouling performance. In this study, a new PVDF/PAN/TiO2 ultrafiltration blend membrane was prepared via phase inversion by dispersing TiO2 nanoparticles in the PVDF/PAN casting solutions. The effect of different concentrations of TiO2 on the characteristics of membranes (i.e., morphology, hydrophilicity, permeation performance, and antifouling properties) was investigated. Results of scanning electron microscopy analysis showed the finger-like pores and macrovoids decrease due to the presence of... 

Ultrafiltration (UF) membranes were prepared from blends of poly(vinylidene fluoride) (PVDF)/polyacrylonitrile (PAN) via phase inversion method induced by immersion precipitation. Polyvinylpyrrolidone (PVP) was used as pore former and hydrophilic polymeric additive. N,N-dimethylacetamide (DMAc) and water were used as solvent and coagulant (non-solvent), respectively. The effect of different concentrations of PVP on the morphology and performance of the prepared membranes was investigated. Performance of the membranes was evaluated based on pure water flux and filtration of buffered bovine serum albumin (BSA) solution. The contact angle measurements indicated that the hydrophilicity of... 

The purpose of this study is to investigate separation performance of poly(ether-b-amide6) (Pebax1657)/glycerol triacetate (GTA) gel membranes for CO2 removal from H2, N2 and CH4. GTA as a low molecular weight and highly CO2-phill compound was added to membrane structure at various weight fractions, 20%, 40%, 60% and 80% of Pebax, to fabricate a new high solubility selective membrane with improved performance. Permeation of pure gases was studied at different temperatures from 25 to 65°C and pressures from 4 to 24bar and ideal selectivities were calculated. Results indicated enhancement in permeation for all tested gases. For example, at a pressure of 4bar and a temperature of 25°C, membrane... 

In the present study, the morphology of asymmetric poly(vinylidene fluoride) blend membranes which were prepared by the phase inversion method is rationalized by comparing two non-dimensional number represent thermodynamic and kinetic properties of the prepared membrane. These two parameters change phase diagram and demixing rate between solvent and nonsolvent. TiO2 nanoparticles and polyvinylpyrrolidone were used as additives. Hansen solubility parameters of the components are calculated by Van Krevelen method. Furthermore, kinetic and thermodynamic properties of the prepared solutions are determined by drawing phase diagrams and controlling mass transfer rate during precipitation of...