Sharif Digital Repository

In this study, performance of a flat plate solar collector operating in conjunction with a closed-loop pulsating heat pipe is investigated experimentally. The experiments were carried out in Yazd, Iran. The experimental setup consisted of a flat plate solar collector, pulsating heat pipe, and a tank. The pulsating heat pipe's evaporator is located inside the flat plate collector. In order to investigate the effect of the evaporator length on the efficiency of the system, three different length collectors are manufactured in the evaporating section. In addition, the effects of the pulsating heat pipe filling ratio, inclination angle, and flow rate are investigated for each collector... 

Design and fabrication of solar collectors with high performance of energy efficiency to convert solar energy to utility energy is vitally important. This article reports the results obtained from design, construction and investigation of the performance of a Combined Multi-Purpose Vacuum Solar Collector (CMPVSC). This collector consists of three sections: the vacuum section, the liquid section and the air section. In the present collector, it is capable of transferring heat to two flows (liquid and air) simultaneously and separate with the possibility of multipurpose applications. The CMPVSC is compared with the existing individual collectors and the effects of different parameters on the... 

In this study, the effect of graphene nanoplatelets (GNP)/distilled water nanofluid on the thermal performance of evacuated tube solar collector (ETSC) water heater was experimentally investigated. The mass percentage of GNP was considered at 0.025, 0.5, 0.075 and 0.1 wt%. The physical and thermal properties of the GNP nanofluids including stability, specific heat capacity, viscosity and thermal conductivity were investigated. The thermal efficiency tests on the solar collector were carried out for varying volumetric flow rate of 0.5, 0.1, and 1.5 L/min while the ASHRAE standard 93–2003 was considered to calculate the efficiency of the collector. The results indicated that the solar... 

A considerable amount of energy is lost in the parabolic trough solar collectors due to the poor capability of working fluid in full absorption of the concentrated solar irradiation across the receiver tube. A new hybrid method is recommended here to cover up such deficiency by simultaneously using a rotary absorber tube and magnetic field inducer with nanofluid. Results showed that the combination effects of the receiver rotation and the magnetic field improve the convection mechanism in the absorber and increase both energetic and exergetic performance of the collector. The study reveals that there is an optimal rotational speed in the each magnetic field intensity for different... 

The solar collectors have been commonly used in desalination systems. Recent investigations show that the use of a linear parabolic through collector in solar stills can improve the efficiency of a desalination system. In this work, a combination of a heat pipe and a twin-glass evacuated tube collector is utilized with a parabolic through collector. Results show that the rate of production and efficiency can reach to 0.27 kg/(m2 h) and 22.1% when aluminum conducting foils are used in the space between the heat pipe and the twin-glass evacuated tube collector to transfer heat from the tube collector to the heat pipe. When oil is used as a medium for the transfer of heat, filling the space... 

Solar collecting area is one of the most important operating parameters of active solar stills. No experimental work has been performed to investigate the effect of this parameter to date. Furthermore in all of previous theoretical studies the effect of solar collecting area was examined during only the first 24-hour period of the operation of stills with one specified brine depth. However the present work experimentally studies the long-term simultaneous effects of collector area and brine depth on the performance of active solar stills. For this purpose four parallel active solar stills with different collector areas were fabricated and experiments were conducted for 5 consecutive days... 

Today, the production of energy and electricity is one of the major concerns of mankind. Electricity generation by solar energy is considered as one of the alternatives to fossil fuels. Solar chimneys mechanism is based on a natural phenomenon. In this process the solar energy heat up the earth's surface and the surrounding air. Due to the density difference between cold air and warm air, heated air ascends and causes air circulation. In this study, mathematical modelling of solar chimney and governing equations of this system will be discussed. In order to validate the numerical results, upwind velocity in chimney has been compared with a reliable reference results. As well as, the... 

This research is aimed at geometric analysis of parabolic trough solar collector (PTC) in different sizes of the main components of the system. The rate of the Local Concentration Ratio (LCR) on the receiver tube and optical efficiency are two main features in geometric optimization of the parabolic trough solar collectors. In this work, parabolic trough solar collector was optimized for different sizes with three design variables: the receiver diameter, the collector aperture width and the rim angle. The method used in this research was the Monte Carlo Method (MCM) in MATLAB. The optical and geometric modeling was developed for coding in MATLAB. For the case study, a parabolic trough solar... 

Flat plate solar collectors waste a massive part of the heat accumulated near the contact region, mainly due to poor thermal characteristics of working fluid. The demanding power for pumping the flow through the pipes seems a permanent concern in solar collectors. Also, active methods seem not to be applicable in such systems due to the external energy requirement and cost associated with it. An innovative and simple technique is considered here to eliminate such deficiencies all at once by equipping the flat plate collector with rotary absorber pipes and Fe3O4/water nanofluid. Results indicate that the applied method improves the convection mechanism in each pipe by mixing the accumulated... 

The yearly thermo-economic performance is dynamically investigated for three solar heating and cooling systems: solar heating and absorption cooling (SHAC), solar heating and ejector cooling (SHEC), and heating and solar vapor compression cooling (HSVC). First, the effects of important design parameters on the thermo-economic performance of the systems to supply the heating and cooling loads of the building are evaluated. The systems are parametrically analyzed with the weather conditions of Tehran, Iran. The results show that the life cycle costs (LCC) of the SHAC and HSVC systems are alike and much lower than those of the SHEC system. The HSVC system exhibits the best performance from... 

Fog harvesting is an unconventional source of water that can be used in some regions with water scarcity to overcome water shortages. The most commonly used collectors are meshes which have intrinsic limitations, the most important of which are clogging and aerodynamic deviation of droplets around the wires. Here, three techniques are compared and combined to overcome these limitations, i.e., replacing the mesh with an array of vertical wires, addition of a hydrophobic layer to the wires, and forcing the ionized droplets to move toward the wires by applying an electric field. The combination of these techniques was found to result in higher fog harvesting efficiency compared to each... 

In this paper the creation of multiple energy hubs that make up a complex energy network are modeled and optimized for a selection of six scenarios to examine both their financial viability and potential reduction of greenhouse gas emissions. As a proposed case study scenario for the model, three energy hubs are considered: a 'residential complex (RC)', a 'commercial shopping plaza (CS)', and a 'school (S)'. The use of combined heat and power systems, solar photovoltaic, solar collectors and network interaction are also examined for their impact on efficiency and cost. The modeling is undertaken and carried out by General Algebraic Modeling System (GAMS). It is shown that cost can be reduced... 

Due to significant reduction in fossil fuel sources, several researches have been conducted recently to explore modern sources of renewable energy. One of the major fields in the category of renewable energy harnessing devices is parabolic trough solar collector (PTC). Several parameters have effect on the overall efficiency of the PTCs. As the effect of these parameters is coupled to each other, a comprehensive investigation is necessary. In the present study, a numerical analysis is performed to examine the efficiency of PTCs via variation of several governing parameters (e.g., wind velocity magnitude, nanoparticles volume fraction, inlet temperature, and reflector's orientation). A... 

Parabolic trough solar collector (PTC) is one of the most mature and widely used type of solar energy harnessing devices. Therefore, investigation of the effect of various operational conditions on the overall efficiency of these devices has been topic of substantial interest in the recent decade. Moreover, utilization of nanoparticles as a useful additive to the working fluid should be examined thoroughly to optimize the collector's outputs. To do so, in the present study, energy and exergy efficiencies of a typical PTC as a function of several involving parameters are numerically calculated. These parameters are nanoparticle volume fraction (from 0 to 5 percent), environment wind speed... 

The exergoeconomic analysis is a powerful tool to study an energy system and provide rational decision-making for it. This paper is aimed at exergoeconomic optimization and sensitivity analysis evaluation of the results of a commercial parabolic trough collector (PTC). First, an analysis of optical, thermal, exergy, and economic equations of the PTC system is presented. Then, the objective function and variables are optimized through MATLAB software using the hybrid algorithm code. The objective function as the exergy loss rate is a combination of exergy loss and system cost. The evaluation of the results has been carried out considering the radiation intensity in different months of the... 

Global warming escalation has extended average temperature of earth beyond its safe limit. To avert this environmental-threat, solar energy has acquired substantial attention of remarkable researchers in this century. To effectively utilize solar energy by transforming into thermal and electrical energy, the involvement of nanofluids having intensified thermal, optical and magnetic properties, has become very popular. The foremost objective of this article is to provide a comprehensive review on the applications of nanofluids in solar energy systems like solar collectors, photovoltaic cells, solar stills, and thermal energy storage, which are thoroughly discussed in this paper. The effect of... 

Alumina nanofluids are one of the most useful nanofluids, especially for increasing the thermal conductivity. Due to importance of porous media in the improvement of heat transfer, this study investigates the transport and retention of gamma alumina/water nanofluid in the water-saturated porous media. For this purpose, alumina nanofluids were introduced to the porous media consisting of water-saturated glass beads possessing various pH values (4, 7 and 10) and different ionic strengths (0.001 M of KCl, CaCl2, AlCl3, K2SO4, CaSO4, Al2(SO4)3, K2CO3 and CaCO3). Then the break through curve of each experiment was drawn and modeled by combining classical filtration theory with... 

Perovskite solar cells are well known for being low cost, solution-based, and efficient solar cells; however, the high price of the conventional hole-collector electrode (Spiro-OMeTAD/Gold) and the high price and complexity of depositing gold on large scales are major barriers against commercializing them. Herein, an effective carbon composite electrode is introduced for a low-cost perovskite solar cell with CuIn0.75Ga0.25S2 hole transport material to solve this problem. The carbon electrode is deposited by the doctor blade method using a paste composed of flakes of graphite, carbon black, and a kind of hydrophobic polymer (polystyrene or poly-methyl methacrylate). It is investigated how the... 

A considerable amount of energy is lost in the parabolic trough solar collectors due to the poor capability of working fluid in full absorption of the concentrated solar irradiation across the receiver tube. A new hybrid method is recommended here to cover up such deficiency by simultaneously using a rotary absorber tube and magnetic field inducer with nanofluid. Results showed that the combination effects of the receiver rotation and the magnetic field improve the convection mechanism in the absorber and increase both energetic and exergetic performance of the collector. The study reveals that there is an optimal rotational speed in the each magnetic field intensity for different... 

Perovskite solar cells (PSCs) have excellent photovoltaic properties. There are, however, challenges of materials cost and device stability to be solved before commercializing them. Utilizing low-cost inorganic hole transport materials (HTM) as a replacement for spiro-OMeTAD, and replacing the Au electrode with printable carbon could be important steps in this regard. For this purpose, CuInxGa1-xS2 (x = 1, 0.75, 0.5, 0.25, 0) nanoparticle layers are deposited as inorganic HTMs with carbon composite electrode as the back electrode. Photovoltaic properties of PSCs with CuInxGa1-xS2/Carbon hole collecting electrodes are studied by changing the In ratio in the HTM layer. Results from impedance...