Sharif Digital Repository

A composite surface coating is prepared by electropolymerization of a mixture of pyrrole and carbon nanoparticles onto a glassy carbon electrode (GCE). The microscopic structure and morphology of the composite film is characterized by scanning electron microscopy. The modified electrode offers a considerable improvement in voltammetric sensitivity toward methyldopa (m-dopa), compared to the bare and polypyrrole-coated GCEs. A significantly enhanced anodic peak current together with a remarkable increase in sharpness of the cyclic voltammetric (CV) signals are observed for the detection of m-dopa. The effect of experimental parameters, such as scan rate and pH, are investigated by monitoring... 

Manganese dioxide/reduced graphene oxide (MnO2/RGO) nanocomposite material was synthesized by the in-situ anodic pulse electrodeposition method to fabricate symmetric supercapacitors. The effects of the pH value of the electrodeposition bath were considered on the properties of fabricated electrodes. Three pH values of 4, 7, and 10 were evaluated, and physicochemical properties were studied using field-emission scanning and transmission electron microscopy, X-ray diffraction, Fourier-transform infrared spectroscopy, nitrogen gas sorption isotherm, and thermogravimetric analysis. The electrochemical evaluation was performed by galvanostatic charge/discharge (GCD), cyclic voltammetry (CV),... 

A three-dimensional (3D) graphene/Nickel oxide (ERGO/NiO) composite electrode have been fabricated directly on a Nickel foam substrate via a one-step electrochemical co-deposition in an aqueous solution containing Nickel nitrate and GO. By using this simple and one-step electrochemical deposition, it is possible to produce binder-free composite electrodes with improved electrochemical properties using a low-cost, facile and scalable technique. It is observed from FE-SEM images that graphene oxide sheets affect the electrodeposition of nickel oxide. The optimized ErGO/NiO electrode developed in this work exhibits high charge storage capacity with a specific capacitance of 1715.5 F g−1 at... 

A novel electrode structure is introduced for micro-electrical impedance tomography. The composite electrode structure is made up of gold nanoparticles (AuNPs) and carbon nanotube (CNT) which are deposited on the surface. The nanostructure-based composition of electrodes improved the effective surface area, increased the double-layer capacitance of electrodes, and enhanced the electron transfer on the electrode–analyte interface. The proposed electrodes exhibit lower frequency-dependent electrical properties in impedance measurement. © 2020, Springer Science+Business Media, LLC, part of Springer Nature  

A composite film constructed of surfactant doped over-oxidized polypyrrole and multi-walled carbon nanotube was prepared on the surface of glassy carbon electrode by the electro-polymerization method. Surface characterization of the modified electrode was performed by scanning electron microscopy, cyclic voltammetry and electrochemical impedance spectrometry. The investigations have been proved that the over-oxidation of the modifier film resulted in a porous thin layer that improves the interlayer diffusion mechanism for the electroactive species. On the other hand, the negative charge density on the surface of the electrode excludes the negative analytes (e.g. ascorbate and Fe(CN)63?/4?)... 

PbS nanoparticles were in situ deposited on graphene sheets by a successive ionic liquid adsorption and reaction method to prepare a graphene/PbS composite counter electrode for CdS/CdSe quantum dot sensitized solar cells (QDSCs). Under 1 sun illumination, the cells with graphene/PbS counter electrodes (CEs) show a maximum energy conversion efficiency of 2.63%, which is remarkably higher than that of those employing PbS (1.28%) or graphene (0.23%) CEs. Electrochemical impedance spectroscopy analysis shows that graphene/PbS composite counter electrodes have lower charge-transfer resistance at the interface of the CE and the polysulfide redox electrolyte, compared to those cells with PbS and... 

A hierarchical core-shell structure composed of ZnO nanotubes/MnO2 nanosheets was fabricated via a two-step electrochemical deposition procedure on the surface of a 3D graphene network (3DGN) as a free-standing monolithic electrode. In the first step, ZnO nanorod arrays were grown on the surface of a 3DGN followed by electrochemical deposition of MnO2 nanosheets in the next step, which caused the inner parts of initial ZnO nanorods to etch away and resulted in the formation of ZnO nanotubes (ZnO NTs). The highly porous interconnected graphene backbone offers very high conductivity and a large accessible surface area. On the other hand, the formation of ZnO nanotubes can enhance the... 

The high charge carrier recombination rate and weak oxygen evolution kinetics have impeded the efficiency of WO3 photoelectrodes for water splitting. We present a novel type II heterojunction semiconductor based on mixed WS2 and MoS2 nanosheets on WO3 nanoflakes hydrothermally grown on highly porous W skeletons. The chemically exfoliated transition metal dichalcogenide (TMD) sheets with submicrometric lateral sizes were deposited on the surface of WO3 nanoflakes by the electrophoretic technique to fabricate a staggered gap heterojunction. The photoanode exhibited an impressive current density of 14.9 mA cm−2 at 1.23 VRHE which comprised ∼1.7 mA cm−2 photocurrent under 100 mW cm−2 simulated... 

Nowadays, there is a growing interest in synthesizing electrodes used in zinc electrowinning, increasing active surface area, decreasing specific energy consumption, and the oxygen evolution reaction (OER) overpotential. In this study, modified nanocomposite anodes were synthesized by applying pulsed and constant direct current electrodeposition to improve the catalytic activity of the electrodes toward the oxygen evolution reaction (OER) and reduce energy consumption in zinc electrowinning. By decreasing particle size, the active surface area of PbO2-RuO2 nano-mixed composite electrode was 2.88 and 14.22 times greater than PbO2-RuO2 microcomposite and pure PbO2 electrodes, respectively.... 

The electrochemical oxidation of sumatriptan on the surface of carbon paste electrode modified with multi-walled carbon nanotube and cobalt methyl-salophen complex is studied by using cyclic voltammetry and polarization studies. The results indicate that the drug is irreversibly oxidized in a one electron oxidation mechanism. It was found that the peak potential shifted negatively with increasing pH, confirms that H + participate in the oxidation process. The electrode is shown to be very effective for the detection of sumatriptan in the presence of other biological reductant compounds. The prepared modified electrode exhibits a very good resolution between the voltammetric peaks of...