Sharif Digital Repository

Power amplifiers require linearization in order to reduce adjacent inter-modulation distortion without losing efficiency. Digital predistortion is a cost effective method to achieve this goal and it needs an accurate model of the amplifier. Most of the amplifier models are based on memoryless modeling. This kind of modeling is simple but it's not accurate enough if linearization is important; and also for wide band modulations like QAM, we should consider the memory effects of power amplifiers. © 2009 IEEE  

We propose a facile and cost effective method for fabricating superhydrophobic surfaces with significant drag reduction in a wide velocity range. A dual structure superhydrophobic aluminum surface with a hydrophobic Al2O3micro- and nanoparticle coating and also another superhydrophobic surface with a nanoparticle layer coating are fabricated. Then, the resulted drag from each of these surfaces is measured carefully in different velocities and compared with the drag of the as-received aluminum surface. Our results reveal that the surface with the dual structure experiences drag reduction in a wider velocity range compared with the nanoparticle coated sample. Drag reduction of the dual... 

In this research, the employment of an innovative but simple and cost effective method for turbulent reduction in a low speed wind tunnel is investigated and the effect of this turbulence reduction on the Power Spectrum and FFT-Based signals that obtained from Hot-wire Anemometry is studied. These terms represents the amount of power contained in the signals. Several situations are studied in this paper. One of these situations is when there are four screens in the settling chamber of the wind tunnel and after that by adding the trip strip in the contraction region of the wind tunnel the tests were repeated. In the next stage, three screens were removed from the settling chamber of the wind... 

This paper presents a compact and cost effective method for on-chip separation of silica-coated magnetic nanoparticles (SMNPs) with different hydrodynamic size. Three types of SMNPs (Fe3O4@SiO2) with the same magnetic core but with different thickness of silica shells were successfully separated using the developed microfluidic platform. The innovative aspect of the presented separation method is that the induced velocity on the three different types of SMNPs while imposed to the same magnetic field gradient in a static fluid is inversely proportional to their overall, non-magnetic volume. This is due to the enhanced Stokes’ drag force exerted on the nanoparticles (NPs) resulting from their... 

Monoframe droplet shadow velocimetry (mf-DSV) is a cost-effective method in the quality control process of the injectors. In this method, the planar (2D) velocity of the droplets is measured by tracking the droplets in a volumetric illumination, known as shadowgraphy technique. An image with two footprints of each droplet in time lapse of two light pulses is used to determine the displacement/velocity. The mf-DSV method could be established by a much less expensive setup than the traditional velocimetry method. A high-power LED-based light source and ordinary camera without capability of double shutter mode are the requirements of this method. In this paper, different stages of image... 

Nowadays, the LiNi0.8Co0.1Mn0.1O2 (NCM811) cathode material has attracted great research interest due to its high energy density and less usage of costly raw materials. However, the high nickel content of NCM811 brings about an extremely unstable interface between the electrode and electrolyte and therefore inferior cyclic stability. Herein, we have proposed a straightforward method to deliver 1, 2, and 4 wt % of TiO2 nanoparticles (NPs) on the surface of the NCM811 cathode material and to improve its properties at room and high temperatures. Based on scanning electron microscopy and transmission electron microscopy observations, the coating thickness varies from 10 to 35 nm and the 2 wt %... 

A hierarchical superhydrophobic surface is prepared via a two-step boiling water immersion process and anodization of the treated aluminum substrate in a novel hydrophobic electrolyte of aluminum nitrate and stearic acid mixture at room temperature. The immersion time in boiling water had a significant influence on the morphology and durability of the sample. A pseudoboehmite coating is created on the aluminum surface during the boiling process, as revealed by the field emission scanning electron microscopy (FE-SEM) and Fourier transform infrared (FTIR) spectrophotometer results. The energy-dispersive x-ray spectroscopy analysis confirmed the formation of hydrophobic coating surface after... 

Miniaturized systems based on the principles of microfluidics are widely used in various fields, such as biochemical and biomedical applications. Systematic design processes are demanded the proper use of these microfluidic devices based on mathematical simulations. Aggregated proteins (e.g., inclusion bodies) in solution with chaotropic agents (such as urea) at high concentration in combination with reducing agents are denatured. Refolding methods to achieve the native proteins from inclusion bodies of recombinant protein relying on denaturant dilution or dialysis approaches for suppressing protein aggregation is very important in the industrial field. In this paper, a modeling approach is...