Sharif Digital Repository

Water flooding is widely applied for pressure maintenance or increasing the oil recovery of reservoirs. The heterogeneity and wettability of formation rocks strongly affect the oil recovery efficiency in carbonate reservoirs. During seawater injection in carbonate formations, the interactions between potential seawater ions and the carbonate rock at a high temperature can alter the wettability to a more water-wet condition. This paper studies the wettability of one of the Iranian carbonate reservoirs which has been under Persian Gulf seawater injection for more than 10 years. The wettability of the rock is determined by indirect contact angle measurement using Rise in Core technique.... 

We investigate thin liquid film coating of substrates with trenches via lattice Boltzmann method. The effects of different parameters such as the capillary number, the contact angles and geometric parameters on the results are studied. Our results indicate that for trench depths greater than a critical size coating of the trench is not successful. The critical depth increases by decreasing the capillary number. Moreover we find height, width, capillary number and contact angle under which the coating is successful. The results have been compared with the available results and very close agreement has been achieved  

The process of fluid flow displacement in porous media has recently gained great prominence owing to its widespread usage in a variety of industries, especially in the case of pore scale investigations. Although, many studies have been conducted to address pore-scale investigations in both modeling and experimental approaches, the role of interfacial tension and contact angle on pore-scale phenomena is less focused. In this work, direct pore-scale modeling was used to precisely examine the effect of interfacial tension and contact angle on the fluid flow at the microscale. Also, several pore-scale mechanisms, including Haines jump and dynamic breakup mechanisms, were observed. Therefore, the... 

Recently, wettability alteration has been much attended by researchers for studying well productivity improvement in gas condensate reservoirs. Previous studies in this area only utilized water/alcohol based chemicals for this purpose. While, hydrocarbon nature of the blocked condensate in retrograde gas reservoirs, may motivate application of hydrocarbon based chemical agents. In this study, a new hydrocarbon based wettability modifier is introduced to alter wettability of carbonate and sandstone rocks to preferentially gas wetting condition. Static and dynamic contact angle measurements, spontaneous imbibition and core flooding tests were conducted to investigate the effect of proposed... 

Wettability alteration of rock surfaces toward gas wetting have been recognized as a practical approach for maximizing the production from the gas condensate reservoirs. Most of the reported work in this area applied the so called sessile drop contact angle measurement technique to examine the change in wetting state of a surface. However, the size-dependent wetting behavior of drop which could affect the exact determination of wettability and wettability changes was not well discussed in the previous studies. Therefore, in this work, the size dependency of contact angle for four different liquid-solid-gas systems; i.e., water-calcite-air, water-treated calcite-air (nanofluid treated... 

In this work, sessile drop and low-bond axisymmetric drop shape analysis methods were coupled to provide some new aspects on stick-slip behavior as well as stick time of a drop on calcite surfaces. Slightly hydrophobic calcite surfaces typified with three irregular roughnesses were used to create irregular surfaces to mimic defects for the water-calcite-air systems. Polishing papers of 200, 600, and 1200 grit and a polishing machine were used to prepare surfaces. X-ray diffraction, energy dispersive X-ray spectroscopy, Fourier transform infrared, and atomic force microscopy techniques were employed to evaluate the chemical and physical properties of surfaces. A model was developed to predict... 

Dynamic contact angle measurement; as a standard method for surface wettability analysis, is usually conducted through the analysis of sessile drops formed following the low rate injection of fluid from beneath through a drilled hole via an injection needle. However, understanding/characterizing the changes of drop contact angle from the point where the flat solid surface begins is not well discussed yet. Moreover, during the evaluation of size-dependent behavior of contact angle of millimeter-scale drops, the effect of the drilled hole is ignored. In this regard, in the current study, the experimental and thermodynamic characterizations of the sessile drop advancing contact angle... 

In order to understand the potential role of divalent ions involved in smart water, fluid-fluid and rock-fluid interactions are studied through contact angle and interfacial tension (IFT) measurements. Then, the suitable brines in changing contact angle and IFT are brought into measurement with spontaneous imbibition experiments to evaluate the co-impact of fluid-fluid and rock-fluid interactions. The results show the importance of SO42− ions during smart water injection as removing them from the injection water leads to a sharp drop in ultimate oil recovery. Accordingly, when the concentration of SO42− within the injection water increases four times, 10% ultimate oil recovery is recovered.... 

Low salinity water flooding (LSWF) has the potential to enhance the oil recovery by affecting the fluid-fluid and rock-fluid interactions. Therefore, a systematic investigation on the effect of initial wetting state (water-wet or oil-wet) of pure calcite is conducted to study the importance of these interactions on the effectiveness of LSWF. In the case of initially water-wet cores, more oil recovery efficiency is observed for more saline water cases. To shed light on the possible involved mechanisms, dynamic IFT, dynamic contact angle (CA), oil/brine and rock/brine surfaces zeta potentials, and effluent pH are measured. It is shown that the short-term effect of IFT reduction and long-term... 

Using our recently developed model, for the first time in the literature, the effect of fluid/fluid and rock/fluid interactions on the performance of Low Salinity Waterflooding (LSWF, as an Enhanced Oil Recovery process) at pore-doublet scale is investigated. The model is incorporated into OpenFOAM and both the Navier-Stokes equation for oil/water two-phase flow and the advection-diffusion equation for ion transport (at both fluid/fluid and rock/fluid interface) are solved via direct numerical simulation (DNS). The model is validated against imbibition and drainage pore-doublet experiments reported in the literature, and then applied to investigate the sole effect of wettability alteration... 

Low salinity waterflooding (LSWF) is a process in which by lowering the ionic strength and/or manipulation of the composition of the injection water, the long term equilibrium in oil/brine/rock system is disturbed to reach a new state of equilibrium through which the oil production will be enhanced due to fluid/fluid and/or rock/fluid interactions. In spite of recent advances in the simulation of the LSWF at core scale and beyond, there are very few works that have modelled and simulated this process at the pore scale specially using direct numerical simulation (DNS). As a result the effects of wettability alteration and/or Interfacial Tension (IFT) change on the distribution of the phases... 

Laboratory experiments have shown that performance of waterflooding in oil reservoirs could be significantly increased by lowering the ionic strength and/or manipulation of its composition, which is generally known as low salinity waterflooding (LSWF). The involved mechanisms in additional oil production can be generally categorized in two categories, fluid/fluid and fluid/rock interactions. The distribution of the phases and the involved displacement mechanisms would be strongly affected by the inter-relations between capillary and viscous forces. Although there have been recent advances in the simulation of the LSWF at core scale and beyond and some models are included in commercial... 

Using our recently developed model, for the first time in the literature, the effect of fluid/fluid and rock/fluid interactions on the performance of Low Salinity Waterflooding (LSWF, as an Enhanced Oil Recovery process) at pore-doublet scale is investigated. The model is incorporated into OpenFOAM and both the Navier-Stokes equation for oil/water two-phase flow and the advection-diffusion equation for ion transport (at both fluid/fluid and rock/fluid interface) are solved via direct numerical simulation (DNS). The model is validated against imbibition and drainage pore-doublet experiments reported in the literature, and then applied to investigate the sole effect of wettability alteration... 

Low salinity waterflooding (LSWF) is a process in which by lowering the ionic strength and/or manipulation of the composition of the injection water, the long term equilibrium in oil/brine/rock system is disturbed to reach a new state of equilibrium through which the oil production will be enhanced due to fluid/fluid and/or rock/fluid interactions. In spite of recent advances in the simulation of the LSWF at core scale and beyond, there are very few works that have modelled and simulated this process at the pore scale specially using direct numerical simulation (DNS). As a result the effects of wettability alteration and/or Interfacial Tension (IFT) change on the distribution of the phases... 

Laboratory experiments have shown that performance of waterflooding in oil reservoirs could be significantly increased by lowering the ionic strength and/or manipulation of its composition, which is generally known as low salinity waterflooding (LSWF). The involved mechanisms in additional oil production can be generally categorized in two categories, fluid/fluid and fluid/rock interactions. The distribution of the phases and the involved displacement mechanisms would be strongly affected by the inter-relations between capillary and viscous forces. Although there have been recent advances in the simulation of the LSWF at core scale and beyond and some models are included in commercial... 

Low salinity waterflooding (LSWF) is a process in which by lowering the ionic strength and/or manipulation of the composition of the injection water, the long term equilibrium in oil/brine/rock system is disturbed to reach a new state of equilibrium through which the oil production will be enhanced due to fluid/fluid and/or rock/fluid interactions. In spite of recent advances in the simulation of the LSWF at core scale and beyond, there are very few works that have modelled and simulated this process at the pore scale specially using direct numerical simulation (DNS). As a result the effects of wettability alteration and/or Interfacial Tension (IFT) change on the distribution of the phases...