Sharif Digital Repository

In this paper, we present a computational study on the electrical behaviour of self-switching transistors (SSTs) based on InGaAs/InP heterojunction. Our simulation is based on the solution of Poisson and Schrodinger equations self-consistently by using Finite Element Method (FEM). By using this method, electrical characteristics of device, such as (Formula presented.) ratio, subthreshold swing, and intrinsic gate-delay time are investigated. Also, the effects of geometrical variations on the electrical parameters of SSTs are simulated. We show that appropriate design of the device allows current modulation exceeding (Formula presented.) at room temperature. © 2021 Informa UK Limited, trading... 

In this study electrical properties of different water liquids at frequency range of 100-2000 Hz are investigated by using the short invasive and non-invasive cylindrical capacitive sensors (CCSs). Operation of the capacitance measurement module for such probes is based on the auto balancing bridge method. Comparison of the measured capacitances and measured resistances for different water liquids shows decrease by increasing the frequency. In another study the dielectric constant of distilled water, mineral water, tap water and salt water are measured. The effects of the frequency on the resistivity, permittivity and conductance of the different water liquids are also investigated  

The resistance and capacitance values of the water samples are measured by using two different cell probes (length 10 cm and 5 cm) and a measuring module. Measured conductivities for the different water samples are compared where the lowest conductivity is obtained for the distilled water (3.28 μS/cm) and the highest value is for the boiled water 325.91 μS/cm. Using the measured series resistance values, and by knowing the frequency (1 kHz), the imaginary part of permittivity value is also determined. The imaginary part of the permittivity for the distilled water with the long cell probe is about 0.524 × 10 -7 F/m (for the short probe is 0.523 × 10-7 F/m) while for the boiled water sample is... 

Electro-oxidation of alcohols (methanol, ethanol, 1-propanol and 2-propanol) on nickel dispersed into a thick layer of poly-o-aminophenol on graphite electrode (GE/POAP-SDS/Ni) was investigated. Ni-doping into the polymeric film was achieved chemically followed by enrichment of Ni(III) through cycling the potential. The electro-oxidation of alcohols on GE/POAP-SDS/Ni were found to be dominated by direct electro-oxidation with some contribution from Ni(II)/Ni(III) couple. Rate constants for the electro-oxidation of methanol, ethanol, 1-propanol and 2-propanol as derived by chronoamperometry were 1.65 × 105, 1.31 × 105, 2.53 × 104 and 1.40 × 104 cm3 mol-1 s-1, respectively. Impedance... 

Utility harmonic impedance estimation is an important stage for the study and control of electrical networks power quality such as harmonic sharing determination between a utility and a customer at a point of common coupling (PCC). In this estimation, non-invasive methods, as compared with invasive methods, are more desirable since they do not need to apply intentional disturbances to the power network and can work based on natural load fluctuations. The only concern about such methods is the method accuracy. These methods require simultaneous and synchronous measurements of the voltage and current at the PCC. However, one of the causes of error in the utility harmonic impedance measurement... 

This paper introduces a new concept that we call smart transmission expansion planning (TEP) based on unconventional high surge impedance Loading (HSIL) line designs that will revolutionize power delivery. To date, these two areas (TEP and transmission line design) have been conducted separately. For TEP, planners use the electrical parameters of a few standard conventional line designs to study planning scenarios, and then, the final candidate line is constructed. In such a sequence, cost-effective scenarios often do not meet the technical criteria of load flow. This paper will demonstrate that this sequence can be overturned; namely, a transmission expansion planner can get optimal line... 

In this paper, we present a computational study on the electrical behaviour of self-switching transistors (SSTs) based on InGaAs/InP heterojunction. Our simulation is based on the solution of Poisson and Schrodinger equations self-consistently by using Finite Element Method (FEM). By using this method, electrical characteristics of device, such as (Formula presented.) ratio, subthreshold swing, and intrinsic gate-delay time are investigated. Also, the effects of geometrical variations on the electrical parameters of SSTs are simulated. We show that appropriate design of the device allows current modulation exceeding (Formula presented.) at room temperature. © 2021 Informa UK Limited, trading... 

Various methods have been used for solving the neutron transport equation in the past, and a number of computer codes have been developed based on these solution methods. This paper describes a novel method for the solution of the steady-state and time-dependent neutron transport equation using the duality between neutronic parameters in the method of characteristic (MOC) and the electrical parameters in the cellular neural networks (CNN). The relevant electrical circuit can be simulated by professional electrical circuit simulator software, HSPICE. This software is used for numerical solution of the transport equation only by preparation of appropriate inputs. This method does not need... 

In this research, for the first time, SnO2-based varistors were fabricated via spark plasma sintering technique (SPS) and the microstructure and electrical properties of these varistors were investigated. Furthermore, the effect of post-annealing temperature in oxygen atmosphere on electrical properties of the SPSed samples was studied. The SPS process was performed at the sintering temperatures of 600, 650, and 700 ᵒC for 15 min with a maximum pressure of 90 MPa under vacuum condition. The SPSed sample which was sintered at 650 ᵒC possessed maximum density of 98% and the ultra-fine-grained microstructure with the mean grain size of 380 nm. Surprisingly, all SPSed samples exhibited Ohmic... 

Lithium-ion batteries should continuously be operated at the optimum temperature range (15∼40∘C) for the best performance. Surface temperature monitoring is critical for the safe and efficient operation of the battery. In this study, initially, the electrical parameters of the battery are determined by applying a second-order equivalent circuit model. This model then is integrated with a thermal model based on the temperature dependent behavior of the electrical parameters and the heat generated. The input parameters to the electro-thermal model include the current, the ambient fluid temperature and the output parameters include the terminal voltage, state of charge, cell core temperature... 

Under smart grid environment, islanding detection plays an important role in reliable operation of distributed generation (DG) units. In this paper an intelligent-based islanding detection algorithm for PV and DFIG units is proposed. Decision tree algorithm is used to classify islanding detection instances. This algorithm is rapid, simple, intelligible and easy to interpret. The error rate of this method is reduced by Adaptive Boosting (AdaBoost) technique. The proposed method is tested on a distribution system including PV, DFIG and synchronous generator. Probable events in the system are simulated under diverse operating states to generate classification data set. First and second order... 

This paper describes a novel Direct Torque Control (DTC) method for adjustable speed Doubly-Fed Induction Machine (DFIM) drives which is supplied by a two-level Space Vector Modulation (SVM) voltage source inverter (DTC-SVM) in the rotor circuit. The inverter reference voltage vector is obtained by using input-output feedback linearization control and a DFIM model in the stator a-b axes reference frame with stator currents and rotor fluxes as state variables. Moreover, to make this nonlinear controller stable and robust to most varying electrical parameter uncertainties, a two layer recurrent Artificial Neural Network (ANN) is used to estimate a certain function which shows the machine... 

TiO2 layers were grown via pulse type microarc oxidation process under different applied voltages, frequencies, and duty cycles. Surface chemical composition and phase structure of the synthesized layers were studied utilizing X-ray photoelectron spectroscopy (XPS) and X-ray diffraction (XRD). Furthermore, scanning electron microscope (SEM) and atomic force microscope (AFM) were employed to investigate surface morphology and topography of the layers. It was revealed that the layers had a porous structure with both anatase and rutile phases. The anatase relative content in the layers increased with the applied frequency; meanwhile, it decreased with duty cycle at low applied voltages, but... 

This study reports the fabrication of a microfluidic microbial fuel cell (MFC) using nickel as a novel alternative for conventional electrodes and a non-phatogenic strain of Escherichia coli as the biocatalyst. The feasibility of a microfluidic MFC as an efficient power generator for production of bioelectricity from glucose and urea as organic substrates in human blood and urine for implantable medical devices (IMDs) was investigated. A maximum open circuit potential of 459mV was achieved for the batch-fed microfluidic MFC. During continuous mode operation, a maximum power density of 104Wm-3 was obtained with nutrient broth. For the glucose-fed microfluidic MFC, the maximum power density of... 

This study reports the fabrication of a new cathode electrode assembly using polyaniline (PANI) and graphene on a stainless steel mesh (SSM) as an alternative for the conventional expensive cathode of microbial electrolysis cells (MECs). With respect to the previous efforts to propose an efficient and cost-effective alternative for platinum (Pt) catalysts and cathode electrodes, the present study investigates the assessment of different catalysts to elucidate the potential of the modified SSM cathode electrode for larger-scale MECs. In the case of feeding dairy wastewater to the MEC, the maximum hydrogen production rate and COD removal were obtained by SSM/PANI/graphene cathode and had the...