Sharif Digital Repository

In this report, sessile drop technique was employed to study the wetting of alumina by pure aluminium. Contact angle of pure aluminium on the surface of polycrystalline alumina substrate was studied in the temperature range of 750-1100 °C. Electron microscopy and EDX analysis were employed to examine the possible reactions at the melt-substrate interface. It was found that at temperatures in excess of 1050 °C molten aluminium can wet alumina. No reaction layer was detected at the Al/Al2O3 interface. © 2007 Elsevier B.V. All rights reserved  

Hexagonal core–shell SiO2[–MOYI]Cl–]Ag nanoframeworks were synthesized via surface modification of hexagonal silica nanoparticles prepared from perlite (EP) as a cheap and abundant raw material. The prepared samples were well characterized by X-ray diffraction powder (XRD), energy dispersive X-ray (EDX), diffuse reflectance spectroscopy (DRS), Brunauer–Emmett–Teller (BET) specific surface area analysis, fourier transform infrared spectroscopy (FTIR), energy-dispersive X-ray spectroscopy (EDX), and transmission electron microscopy (TEM). The XRD patterns confirmed that Ag and AgCl crystalline phases were successfully loaded on the surface. The TEM images were also implied that the... 

Present research represents the application of artificial neural networks to predict the chemical composition of electrodeposited Ni-Mo thin films. Artificial neural networks commonly are utilized as a prediction tools so that these networks could approximately find kind of logic relationships between inputs and target; they fitted appropriate coefficient and weighting factors to the inputs which are proportional to their importance. In order to evaluate the model developed, experimental results were compared with the predicted ones. However, more data are required to train more reliable prediction models, presents study revealed an acceptable error less than 1% between predicted values and... 

In the present paper, the fabrication and characterisation of typical high temperature Ni(Ti+ Hf) alloyed thin films produced by simultaneous sputter deposition from separate elemental Ni, Ti and Hf targets are presented. Film composition, determined by energy dispersive X-ray spectroscopy, was controlled by adjusting the ratio of powers applied to each target. Films deposited at room temperature had an amorphous structure and subsequent annealing at 550°C was carried out in a high vacuum environment, based on crystallisation temperature evaluation by differential scanning calorimetry (DSC). High temperature martensitic transformation, confirmed by DSC and variable temperature X-ray... 

In present work, an attempt has been made to investigate the wear behavior of particle reinforced composites based on one of the proper magnesium alloys. The SiCP/QE22 composites and QE22 unreinforced specimens were produced via the powder metallurgy route. The volume fractions of SiC particles with three different shapes, i.e. sharp, blocky and round, were selected in the range of 10-25 vol.%. The dry sliding tests were conducted on unreinforced matrix and SiCP/QE22 composites using pin-on-disk apparatus, according to ASTM G99-95a standard. The applied loads were selected as 3, 5 and 20 N. The tests were carried out under sliding speeds of 0.5 and 1.2 m/s. In all tests, the sliding... 

The fabrication of TixNi1-x shape memory films using simultaneous magnetron sputtering from two separate, elemental targets was investigated. The films were deposited at room temperature and then annealed at 500 °C to achieve the shape memory effect. The influence of sputtering parameters such as power ratio to the targets (to control the composition) and Ar gas pressure (to control the film structure) were studied. It was found that the Ar gas pressure had a critical influence on the shape memory effect of the films. Characterization of the films was carried out by energy dispersive X-ray spectroscopy in a scanning electron microscope (to measure the film composition and uniformity), in... 

The aim of current research is to investigate the substrate electropolishing effect on corrosion resistance of Ni-Mo thin films. For this purpose, corrosion resistance of coatings deposited on mild steel substrates, that was electropolished or mechanically polished, have been compared in 3.5 wt.% NaCl solution using potentiodynamic polarization and electrochemical impedance spectroscopy (EIS). The structural properties of Ni-Mo thin films were evaluated using X-ray diffraction (XRD) and their morphology, microstructure and chemical composition were also investigated using scanning electron microscopy (SEM) and X-ray energy dispersive spectroscopy (EDS). Temperature and acidity of deposition... 

Due to the strong magnetic anisotropy energy, the L10 FePt nanocrystals are considered as one of promising candidates for magnetic recording media with ultrahigh densities. The surfaces of Si and SiO2 wafers have been covered by FePt nanoparticles (NPs) and heated at 600 °C for 1 h to form the L10 phase. Bonding of NPs with the SiO2 surface in the presence of magnetic field during annealing process controls the L10 FePt NPs size and their uniform surface distribution. In the presence of perpendicular magnetic field to the surface, the size of NPs obtains up to 30 nm with coercivity of 5.8 kOe and in parallel magnetic field, the NPs size reaches to 45 nm with coercivity of 2.9 kOe. These... 

The unique properties of NiTi alloy, such as its shape memory effect, super-elasticity and biocompatibility, make it ideal material for various applications such as aerospace, micro-electronics and medical device. In order to meet the requirement of increasing applications, great attention has been given to joining of this material to itself and to other materials during past few years. Laser welding has been known as a suitable joining technique for NiTi shape memory alloy. Hence, in this work, a comparative study on laser welding of NiTi wire to itself and to AISI 304 austenitic stainless steel wire has been made. Microstructures, mechanical properties and fracture morphologies of the... 

The present work investigates joining of two MoSi2 parts through Cusil/Zr/Cusil interlayer with Cusil being a commercial eutectic of Cu-Ag alloy. The joining operation was implemented in an inert gas tube furnace by brazing. The brazing temperature ranged from 800 to 930°C while the operation lasted for 60min. Evaluation of joints strength through shear loading identified the maximum strength 60.31MPa for the brazed sample at 830°C. Interfacial microstructure was studied by Scanning Electron Microscopy (SEM), Energy Dispersive Spectroscopy (EDS) and X-ray Diffraction (XRD) techniques. Applying the temperature of 830°C was led to a uniform dense joint consisting of various phases with... 

In this work, the effects of the annealing temperature and duration on the joint strength of the steel/aluminum lap joints made by friction stir welding were investigated. The strength of the welded joints was evaluated by shear-tensile test. Formation of intermetallic layer at the joint interface and the fracture locations were studied using scanning electron microscopy (SEM) equipped with energy dispersive spectroscopy (EDS) and electron backscatter diffraction (EBSD). The results indicated that longer time of annealing treatment resulted in higher joint strength at 300 and 350 °C and that the rate of the increase in joint strength with time was about 72% higher at the latter temperature... 

The aim of this paper is to study the influence of frequency in pulse electrodeposition, on the current efficiency, Ni content and surface morphology of deposits from a novel cyanide-citrate electrolyte with 20 mM gold as KAu(CN) 2 and 7 mM NiSO 4, with the aim of design of experiment by respond surface method (RSM). Frequency was in the range of 1-200 Hz in constant average current density, temperature, and duty cycle of 7 mA/cm 2, 59 °C and 55% respectively. Composition of the deposits was determined by atomic absorption spectroscopy (AAS). Additionally, deposits were characterized by scanning electron microscopy (SEM), and Energy-dispersive X-ray spectroscopy (EDS). It was shown that from... 

This article reports experimental results on laser sintering of A356 aluminum alloy and A356/SiC composite powders. Effects of scan rate, sintering atmosphere, hatch spacing, and SiC volume fraction (up to 20%), and particle size (7 and 17 μm) on the densification were studied. The phase formation and microstructural development were analyzed by X-ray diffraction (XRD) and scanning electron microscopy (SEM) coupled with energy-dispersive X-ray spectroscopy (EDS). Laser sintering under argon atmosphere exhibited higher densification compared to nitrogen. A faster sintering kinetics was observed as the scan rate decreased. Except at a low SiC content (5 vol%), the composite powders exhibited... 

The aim of this research was to present an experimental method for large-scale production of silver chloride nanoparticles using spinning disk reactor. Silver nitrate and sodium chloride were used as the reactants, and the protecting agent was gelatin. The experiments were carried out in a continuous mode by injecting the reactants onto the surface of the spinning disk, where a chemical precipitation reaction took place to form AgCl particles. The effects of various operating variables, including supersaturation, disk rotational speed, reactants flow rate, disk diameter, and excess ions, on the particle size of products were investigated. In addition, the AgCl nanoparticles were... 

Purpose – This paper aims to clarify the corrosion behavior of two famous structural steels in sour environment. These steels have a vast application in oil and gas industries. The study aims to find the effect of different concentrations of sour solution on the origin of crack in these steels. Design/methodology/approach – After preparation of specimens, different sour solutions were made using the synthetic brine (according to National Association of Corrosion Engineers [NACE], Technical Committee Report 1D182) and various amounts of Na2S.9H2O and CH3COOH. The polarization test was done by Potansiostat apparatus model Zahner-IM6 at two temperatures, 25°C... 

The main challenges of biological implants are suitable strength, adhesion, biocompatibility and corrosion resistance. This paper discusses fabrication, characterization and electrochemical investigation of anodized Ti6Al4V without and with a hydroxyapatite (HA) layer, HA/TiO2 nanoparticles (NPs) and HA/TiO2 nanotubes (HA/anodized). X-ray diffraction (XRD), field emission scanning electron microscopy (FE-SEM) and energy dispersive spectroscopy (EDS) were used to characterize and compare properties of different samples. Dense HA with uniform distribution and 12.8 ± 2 MPa adhesive strength enhanced to 19.2 ± 4 MPa by the addition of TiO2 nanoparticles and enhanced to 23.1 ± 4 MPa by the... 

In the present work, spark plasma sintering (SPS) process was employed to prepare a nanostructured yttria-stabilized zirconia (8YSZ) coating on a nickel-based superalloy (INCONEL 738) with functionally graded structure. A stack layer of INCONEL 738/NiCrAlY powder/Al foil/NiCrAlY+YSZ powder/YSZ powder was SPSed in a graphite die at an applied pressure of 40 MPa under an vacuum atmosphere (8 Pa). The sintering temperature was ∼1040 °C. For comparison purpose, the air plasma spray (APS) technique was employed to prepare the thermal barrier coating (TBC). Microstructural studies by scanning electron microscopy showed that the SPSed coating was sound and free of interfacial cracks and large... 

A simple platform based on a hairpin oligonucleotide switch and multi-walled carbon nanotubes (MWCNTs) for the ultrasensitive detection of specific DNA sequences has been developed. In this approach, the π-stacking interaction of single-strand DNA-MWCNT was employed to construct an electrochemical DNA biosensor. Changes to the surface conductivity, based on the MWCNT replacement, were monitored by using the electrochemical species [Fe(CN)6]3-/4- as a redox probe. Morphological and voltammetric characterizations of the electrode surface were performed using atomic force microscopy (AFM), energy dispersive spectroscopy (EDS), cyclic voltammetry (CV), differential pulse voltammetry (DPV) and... 

Copper supported on polymer-coated magnetic nanoparticles was designed and synthesized as a separable heterogeneous catalyst. The catalyst was fully characterized using several techniques such as Fourier transform infrared and energy-dispersive X-ray spectroscopies, scanning and transmission electron microscopies, X-ray diffraction, vibrating sample magnetometry, thermogravimetric analysis and inductively coupled plasma atomic emission spectrometry. All results showed that copper was successfully supported on the polymer-coated magnetic nanoparticles. Also, results showed that the synthesized material can be used as an efficient catalyst for the preparation of a series of 1,4-disubstituted... 

In this paper, the failure of the reformer furnace tube, made of HP-Nb micro alloyed heat resistant steel is investigated. The failure was due to a longitudinal crack developing in the circumferential weld joint close to the outlet end of the tube, where the mean wall temperature had reached the highest value during service. According to the temperature records during the period of 7 years of being in service, the tube had experienced temperatures higher than the tubes designed temperature. This situation besides the occurrence of several sudden shutdowns caused the mechanical properties degradation.Macroscopic and microscopic examinations revealed that the failure had occurred due to the...