Sharif Digital Repository

The ring-opening reaction of epoxides with thiols by SbCl3 supported on Kieselguhr under solvent-free conditions, afforded high yields of β-hydroxy sulfides. Nucleophilic attack of the thiols occurs regioselectively at the less hindered side of the epoxides. Copyright © Taylor & Francis Group, LLC  

The physical properties including glass transition temperature and permeability behavior of clay-filled epoxies are reviewed in this chapter. There is no consensus in the literature on how nanoclay affects the α-relaxation temperature in epoxy systems. This perhaps rises from the complexity of nanoclay morphology in polymeric resins and the interphase properties since morphology of nanoclay and interphase characteristics are two key parameters to control the glass transition process in epoxy nanocomposites. In addition, the possible existence of several α-transitions in montmorillonite-filled epoxies due to the existence of several relaxation domains may account for the controversial... 

In this investigation, the mechanical and thermal properties of the montmorillonite-epoxy nanocomposites were studied. The epoxy compounds were prepared by in situ polymerization and the intercalation dispersion were obtained as evidenced using X-ray diffraction (XRD) and transmission electron microscopy (TEM). The results reveal remarkable stiffening effect and slight toughening effect of the MMT in the epoxy resin and an insight about the crack tip and notch tip toughening mechanism. According to the DMA, the glass transition temperature increases as increasing the MMT content. © 2008 World Scientific Publishing Company  

The feasibility of using solid acrylonitrile-butadiene rubbers (NBR) with 19 and 33% w/w acrylonitrile to toughen diglycidyl ether of bisphenol A (DGEBA) epoxy resins has been investigated. Thermal analysis experiments revealed a two-phase morphology of these rubber-modified epoxies. However, the higher content of acrylonitrile in the rubber caused better compatibility between NBR and the epoxy resin. The rubber with 33% acrylonitrile was found to be an effective toughening agent for DGEBA epoxy resins. Fracture surface studies and also the high tensile strength of crosslinked high molecular weight NBR suggest that the toughening effect should arise from rubber bridging and tearing... 

Two types of conventional rubber modifiers and a series of hollow plastic micro-spheres were employed as toughening agents in a diglycidyl ether of bisphenol A (DGEBA) epoxy in Part I (Bagheri R, Pearson RA. Polymer 1996;37:4529) of this study. It was found that the rubber modifiers with different cavitation resistance and hollow plastic micro-spheres which act as pre-existing microvoids toughen epoxies in the same manner. The current study is composed to further examine the previous results in terms of the role inter-particle distance in rubber/microvoid toughened epoxies. It is shown that the fracture toughness in toughened blends goes through a ductile-to-brittle transition with... 

The effect of loading rate on toughening mechanisms of rubber-modified epoxy resin was investigated using amine-terminated butadiene acrylonitrile (ATBN) rubber. Rubber-modified samples were tested at various loading rates in the range of 1-1000 mm/min. At low loading rates, modified resin exhibited a high fracture toughness, which decreased by increasing the rate of loading. At higher loading rate a transition region was observed, where the fracture toughness did not change noticeably with increasing the loading rate. Beyond the transition region, the resin fracture toughness dropped dramatically to the level of unmodified epoxy. Fractography of the damage zone showed different toughening... 

In this paper, we review recent progress made in the field of epoxy-based binary and ternary nanocomposites containing three-, two-, and one-dimensional (i.e., 3D-, 2D-, and 1D) nano-size fillers with a special focus on their fracture behaviors. Despite investigations conducted so far to evaluate the crack-resistance of epoxy nanocomposites and attempts made to clarify the controlling toughening mechanisms of these materials, some questions remain unsolved. It is shown that silica nanoparticles can be as effective as rubber particles in improving the fracture toughness/energy; but incorporation of carbon nanotubes (CNTs) or clay platelets in epoxy matrices delays crack growth only modestly.... 

In this research, the effect of adding graphene-based aerogel ((G)A) nanoparticles on the tensile and fatigue behavior of the epoxy polymer was investigated. Specimens of nanocomposites were prepared by adding 0.05, 0.1, 0.2, 0.5, 1, and 2 wt.-% (G)A nanoparticles to the epoxy polymer. Tensile tests revealed that the 0.1 wt.-% graphene-based aerogel/ epoxy ((G)A/E) nanocomposites had the highest increase in tensile strength with 19 % growth compared to neat epoxy. Also, the tensile modulus increased by 15 % in the 0.5 wt.-% (G)A/E nanocomposites. A substantial improvement in fatigue life of the epoxy polymer was observed on adding 0.1 wt.-% (G)A nanoparticles. For instance, the fatigue life... 

The morphology of a quaternary blend containing a diglycidyl ether of bisphenol-A (DGEBA), a thermoplastic modifier (PMMA), a phase-separating curing agent (diaminodiphenylmethane, DDM), and a non-phase-separating curing agent (methylenebis(3-chloro-2,6-diethylaniline, MCDEA) was studied as a function of volume fraction of the thermoplastic modifier and fractional concentration of the curing agents in their mixture. It was found that using mixtures of curing agents a co-continuous morphology could be obtained at PMMA concentrations as low as 2.5 volume percent. Using FTIR spectroscopy it was proved that specific interactions are present between PMMA and individual amine curing agents. On the... 

The aim of this paper is to investigate adhesion property between nano-layered filler and the polymer matrix using a combination of experimental and micromechanical models as well as the changes in yield strength and stiffness of a layered silicate-filled epoxy nanocomposite. The results indicate that addition of intercalated layered silicate particles increased Young's modulus and yield strength of the epoxy resin, although the increases in stiffness and yield strength are modest, 30% and 4%, respectively. In addition, experimental results were compared with predictive stiffening and strengthening models. The rule of mixtures provides an upper bound for the modulus in these materials, while... 

Epoxy resins have been used as structural materials since the late 1940s. Despite their desirable properties such as high strength, excellent creep resistance, and good adhesion, they suffer from low fracture energy. Rubber modification as a major toughening approach to overcome the inherent brittleness of epoxy polymers was introduced during the early 1970s. Since then, a large number of investigations have been conducted to elucidate different aspects of rubber-toughened epoxies. The present work is a critical review of the field focusing on the important parameters affecting rubber-toughening. The studies reviewed are classified in five categories including roles of matrix ductility,... 

Graphene-based carbon hollow spheres (CHSs) fabrication, doped with 2-mercaptobenzimidazole (MBI) was successfully done in previous work. The active/barrier corrosion protection performance (CPP) of epoxy coatings was evaluated using salt spray test, electrochemical impedance spectroscopy (EIS), and scanning vibrating electrode technique (SVET). Results proved the active/barrier CPP enhancement of epoxy coatings in the presence of 3 wt. % MBI@CHSs. While the presence of MBI and empty CHSs in epoxy coatings did not further improve the active performance. An improvement in the adhesion loss of the epoxy coating, ca. 58 %, was observed in the presence of 3 wt. % MBI@CHSs. © 2021  

Herein, the fracture toughness of ternary epoxy systems containing nanosilica and hollow glass microspheres (HGMS) is investigated. The experimental measurements reveal synergistic fracture toughness in some hybrid compositions: The incorporation of 10 phr of HGMS and nanosilica alone modify the fracture toughness of epoxy by 39% and 91%, respectively. However, use of 10 phr hybrid modifier can enhance the fracture toughness of the resin up to 120%. Observations reveal different toughening mechanisms for the blends i.e., plastic deformation for silica nanoparticles and crack bifurcation for HGMS. Both of these toughening mechanisms additively contribute to the synergism in ternary epoxies  

Toughening of epoxy with different types of modifiers produces a bimodal blend that might show better fracture resistance in comparison with single-modified ones. In this research, bimodal epoxy formulations including mixtures of glass microsphere and silica nanoparticles are explored for possible synergistic toughening. The influence of composition on the glass transition temperature (Tg), tensile characteristics, and fracture toughness (KIC) is investigated. Interestingly, a synergism in fracture toughness is observed when mixtures of modifiers were incorporated. For the fixed overall modifier content, KIC is higher when the volume fraction of glass microsphere is lesser than the volume... 

Rubber modification of hoop filament wound epoxy composites was investigated using amine-terminated butadiene acrylonitrile (ATBN) and carboxyl-terminated butadiene acrylonitrile (CTBN) oligomers. Both mechanical and physical properties of modified composites were investigated and the morphology of the samples was studied via scanning electron microscopy. Results indicated that, when added to the epoxy matrix, ATBN effected a superior increase in toughness, yet a more severe decline in compressive and flexural strength, compared to CTBN. In contrast, in the case of composite samples, incorporation of ATBN led to more favorable mechanical properties, from the viewpoint of both toughness and... 

High chemical resistance is the main prerequisites for materials that are intended to be utilized in usages such as chemicals storage containers production. Nanocomposites of epoxy resin containing nanoclay, CaCO3 and TiO2 nanoparticles were prepared and their chemical resistance was studied. Moreover, the effect of electron beam irradiation was explored. TEM micrographs proved the dispersion of nano-size particles in the polymeric matrix. XRD patterns showed an exfoliated structure for nanocomposite containing 1 % nanoclay and intercalated structures for nanocomposites with higher nanoclay contents. SEM showed the pits that appeared in epoxy/nanoclay structure due to chemical corrosion....