Sharif Digital Repository

This paper presents a unified passive–active fault-tolerant control strategy to compensate the loss of actuators’ effectiveness. The proposed approach is capable of handling the system in pre- and post-fault diagnosis intervals by passive and active approaches, respectively. The stability of the designed system is independent of the accuracy of information provided by the fault detection and diagnosis unit, however, a precise estimation could improve the conservation. Actuator saturation and L∞ disturbances effects are considered in the design stage. The trade-off between maximising the domain of attraction and minimising the effects of L∞ disturbances is tackled by developing a non-constant... 

This paper presents a unified passive–active fault-tolerant control strategy to compensate the loss of actuators’ effectiveness. The proposed approach is capable of handling the system in pre- and post-fault diagnosis intervals by passive and active approaches, respectively. The stability of the designed system is independent of the accuracy of information provided by the fault detection and diagnosis unit, however, a precise estimation could improve the conservation. Actuator saturation and L ∞ disturbances effects are considered in the design stage. The trade-off between maximising the domain of attraction and minimising the effects of L ∞ disturbances is tackled by developing a... 

In this paper the fault-Tolerant control problem for uncertain linear systems in the presence of L, disturbances and actuator saturation is studied. The conflict between enlarging the domain of attraction and attenuating the effect of L, disturbances is tackled by proposing a non-constant state feedback controller. The feedback gains are calculated off-line by using linear matrix inequalities. In addition, the proposed method is capable of tolerating time-varying faults. The suggested approach is implemented on a sample model and the result is compared with other works  

This paper presents a novel fault-tolerant control strategy to compensate the time-varying loss of actuators’ effectiveness. It considers intermediate situations where the fault is not determined precisely (unlike active approaches) but overall estimations about its rate and final value are available through the previous experiences and/or experiments. Based on the estimations, two upper and lower time-varying bounds on the actuators’ effectiveness are established to be exploited in the procedure of controller design. In a special case, where these bounds are constant, the method will be reduced to the conventional passive approach. Also, actuator saturation and the effects of (Formula... 

The attitude fault-tolerant control of a flexible satellite actuated by reaction wheels and magnetic torquer bars is investigated in this article. A low earth orbit is considered for moment perturbations such as drag and gravity gradient. Furthermore, the flexible panels attached to a rigid central body are modeled through the assumed mode approach by a finite set of bending modal motion. The ordinary differential equations of their generalized coordinates are found using Lagrange’s equation, and the resulting dynamical model is validated by comparing its simulation results to the NX Siemens software results. Finally, a fault-tolerant controller based on sliding mode control is suggested and... 

In this paper an approach based on system identification is used for fault detection in a nuclear reactor. A continuous-time Extended Kalman Filter (EKF) is presented, which allows the parameters of the nonlinear system to be estimated. Also a fault tolerant control system is designed for the nuclear reactor during power changes operation. The proposed controller is an adaptive critic-based neuro-fuzzy controller. Performance of the controller in terms of transient response and robustness against failures is very good and considerable  

A new method of integrated guidance and control for homing missiles with actuator fault against manoeuvring targets is proposed. Model of the integrated guidance and control system in the pitch plane with actuator fault and some uncertainty is developed. A control law using combination of adaptive backstepping and sliding mode approaches is designed to achieve interception in the presence of bounded uncertainties and actuator fault. Simulation results show that new approach has better performance than adaptive backstepping and has good performance in the presence of actuator fault  

Reference trajectory management is a method to modify reference trajectories for the faulty system. The modified reference trajectories define new maneuvers for the system to retain its pre-fault dynamic performance. Controller reconfiguration is another method to handle faults in the system, for instance by adjusting the controller parameters (coefficients). Both of these two methods have been considered in the literature and are proven to be capable of handling various faults. However, the comparison of these two methods has not been considered sufficiently. In this paper, a controller reconfiguration mechanism and a reference trajectory management are proposed for the spacecraft attitude... 

AC motor drive systems are sensitive to faults occurring at the power inverter, or at the control system. A novel fault tolerant Field Oriented Control system for induction motors is introduced. The system maintains speed control in the event of sensors malfunction and adverse signal conditions, providing enhanced reliability. The system comprises four different flux estimators which are fused by a Fuzzy aggregation system in order to give a reliable estimate of motor flux. The proposed control system is an effective and easy to implement method giving a potential for motor drive reliability enhancement. © 2006 IEEE  

Fast fault detection and reconfiguration of power converters is necessary in electrical drives to prevent further damage and to make the continuity of service possible. On the other hand, component minimized converters may provide the benefits of higher reliability and less volume and cost. In this paper, a new fault-tolerant converter topology is studied. This converter has five legs before the fault occurrence, and after fault detection the converter continues to function with four legs. A very fast fault detection and reconfiguration scheme is presented and studied. Simulations and experimental tests are performed to evaluate the structure requirements, the digital reconfigurable... 

Continuity of service of wind energy conversion systems as well as their reliability and performances are some of the major concerns in this power generation area. Six-legs AC/DC/AC converters are normally used in modern wind energy systems like as in the system with a doubly-fed induction generator (DFIG). A sudden failure of the converter can lead to the total or partial loss of the control of the phase currents and can cause serious system malfunction or shutdown. Therefore, to prevent the spread of the fault to the other system components and to ensure continuity of service, fault tolerant converter topologies associated to quick and effective fault detection and compensation methods...