Sharif Digital Repository

Injecting low salinity brines is regarded as an enhanced oil recovery (EOR) process through IFT reduction. However, the exact mechanism behind this process is an unsettled and complex issue that has not been well understood yet, especially for heavy crude oil system. Besides, limited information is available regarding the key heavy oil/brine interfacial tension (IFT). The present study aims to investigate the sensitivity of dead heavy crude oil/brine IFT to a wide range of properties/conditions and to reveal the underlying physicochemical mechanisms involved in enhanced oil recovery and IFT reduction by low salinity water injection into heavy oil reservoir. IFT was measured as a function of... 

Injecting low salinity brines is regarded as an enhanced oil recovery (EOR) process through IFT reduction. However, the exact mechanism behind this process is an unsettled and complex issue that has not been well understood yet, especially for heavy crude oil system. Besides, limited information is available regarding the key heavy oil/brine interfacial tension (IFT). The present study aims to investigate the sensitivity of dead heavy crude oil/brine IFT to a wide range of properties/conditions and to reveal the underlying physicochemical mechanisms involved in enhanced oil recovery and IFT reduction by low salinity water injection into heavy oil reservoir. IFT was measured as a function of... 

In this work, a series of solvent- and water-injection scenarios were conducted on horizontal five-spot glass micromodels that were saturated initially with heavy oil. Sandstone and limestone rock look-alike and network patterns with different pore structures were used in the experiments. The results show that the ultimate oil recovery of a water-alternating-solvent (WAS) scheme was greater than that of a simultaneously water-alternating-solvent (SWAS) scheme, and the efficiency of a solvent-soak scheme also offers a greater recovery. Likewise, the WAS scheme resulted in greater oil recovery when compared with continuous solvent injection (CSI), with the same amount of solvent consumption.... 

The Conventional Fire Flooding (CFF) process application feasibility on fractured carbonated reservoirs remained questionable. In this paper first combustion parameters and reaction kinetics of a naturally fractured low permeability carbonated heavy oil reservoir in Iran called Kuh-E-Mond applied to simulation study. After that, simulator has been validated with Kuh-E-Mond combustion tube experiment. Recovery mechanism in single block matrix is different from one in conventional model since oxygen first flows into the fractures and then diffuses from all sides into the matrix. Combustion of the oil in the fractures produces some water ahead of fracture combustion front which prohibits oxygen... 

Steam injection process has been considered for a long time as an effective method to exploit heavy oil resources. Over the last decades, Steam Assisted Gravity Drainage (SAGD) has been proved as one of the best steam injection methods for recovery of unconventional oil resources. Recently, Fast-SAGD, a modification of the SAGD process, makes use of additional single horizontal wells alongside the SAGD well pair to expand the steam chamber laterally. This method uses fewer wells and reduces the operational cost compared to a SAGD operation requiring paired parallel wells one above the other. The efficiency of this new method in naturally fractured reservoir is not well understood.... 

Although alkaline-surfactant-polymer flooding is proved to be efficient for oil recovery from heavy oil reservoirs, the displacements mechanism/efficiency of this process in fractured systems needs to more discussion, especially in five-spot patterns. In this work, several ASP flooding test were performed on fractured micromodels which were initially saturated with heavy oil at constant flow rate and different fracture geometrical characteristics conditions. The ASP solutions are constituted from 5 polymers i.e. four synthetic polymers include three hydrolyzed polyacrylamide with different molecular weight as well as a non-hydrolyzed polyacrylamide and a biopolymer, 2 surfactants i.e. a... 

Toe to heel air injection has been studied on non-fractured sandstone models and is found to be a promising enhanced oil recovery method for certain heavy oil reservoirs, such as those in Canada, but its applicability on fractured reservoirs, such as those in the Middle East, is not investigated yet. The objective of this article is to evaluate the effect of fractures geometrical parameters, such as fracture density, orientation, and location, on the performance of the process in laboratory scale. Simulation results showed that toe-to-heel air injection is more applicable on highly networked fractured reservoirs, such as those that occur in Persian Gulf coast compared to lower density... 

The aim of the present work is to evaluate the effect of fractures geometrical properties such as orientation, density, location, and networking on the conventional fire flooding (CFF) process performance through simulation analysis. Combustion parameters of a fractured low-permeable carbonate heavy oil reservoir in Iran called Kuh-E-Mond (KEM); applied for simulation study and simulator has been validated with KEM combustion tube experimental data. The validated model was modified to study CFF in 3D semi-scaled combustion cells. Simulation results confirmed that CFF is more feasible in the case of densely fractured reservoirs such as those in the Middle East  

The top-down in situ combustion (ISC) involves the stable propagation of the combustion front from the top vertical injector to the bottom horizontal producer. Apart from laboratory studies in conventional sandstones, no application of the process in fractured carbonates has been addressed yet. The authors modified a successful combustion tube history matched model of an Iranian low-permeable heavy oil reservoir called Kuh-E-Mond to investigate the feasibility of ISC in fractured carbonate reservoirs mimicking block-scale combustion cells. Effects of fractured geometrical properties such as orientation, location, extension, density, spacing, and dispersion were considered. Results confirmed... 

This work examines the operational parameters that may influence the performance of toe-to-heel steamflooding in a laboratory-scale simulation model built on the basis of the fluid and rock samples from a fractured, low-permeable, carbonate heavy oil reservoir in Southwestern Iran, called KEM (Kuh-e-Mond). Using vertical (V) or horizontal (H) injectors (I) and producers (P), the effects of different well configurations including VIVP, VIHP, 2VIHP, VI2HP, HIHP, and HI2HP, injectors' traversal distance, producers' traversal distance, and horizontal producer length have been investigated. In summary, the results show that 2VIHP scheme performs best in terms of oil recovery and areal/volumetric... 

Application of solar energy compared to conventional gas-burning boilers for steam generation in thermal Enhanced Oil Recovery processes is a newly attended technology, which brings significant benefits to the petroleum industry through environmental and economical aspects. This technique is especially designed for the regions in which gas-burning steam generation is not viable in large scale. The objective of this study is to investigate about viability of using solar energy to generate steam instead of using conventional steam generators in a Venezuelan extra heavy oil reservoir. Limited gas production policy of the Venezuelan government is the major challenge for utilizing gas steam... 

The main issue in heavy oils enhanced recovery methods is to reduce their viscosity in order to get a better mobility. This is commonly obtained by blending the oil with light hydrocarbons. Co-solvents are good candidates to improve the hydrocarbon recovery efficiency especially in miscible processes. However, the effect of co-solvents on miscible flooding of heavy oil reservoirs at different pore geometries is not well understood. In this work different one-quarter five-spot network patterns along with those generated from reservoir rocks' thin sections were etches on glass surfaces. The models that had been initially saturated with the heavy crude oil were used to perform a series of... 

Water-in-oil emulsion usually forms during waterflooding in some heavy oil reservoirs. The composition and salinity of the injected water critically affect the w/o emulsion droplet size distribution, which control the emulsion stability and emulsion flow in porous media. The aim of the present work is to assess the effect of different sea water salinities on w/o emulsion stability through microscopic imaging. Therefore, w/o emulsions were prepared with different sea water samples, which were synthesized to resemble Persian Gulf, Mediterranean, Red Sea, and North Sea water samples. The results showed that log-normal distribution function predicts very well the experimental data to track the... 

The performance of CO2 injection into a semi-heavy oil reservoir was investigated at reservoir conditions, using highly permeable sandstone in a complete series of PVT tests and coreflooding experiments. Analysis of involved parameters such as: injection rate, injectant type and reservoir pressure were also considered. Oil viscosity reduction and oil swelling are the most influential mechanisms of enhanced oil recovery in this process. The results demonstrated that CO2 injection would decrease the interfacial tension for the high permeable medium in the absence of capillarity, but this reduction may not improve the recovery drastically. One of the main important aspects of this work is the... 

Water-in-oil emulsion usually forms during waterflooding in some heavy oil reservoirs. The composition and salinity of the injected water critically affect the w/o emulsion droplet size distribution, which control the emulsion stability and emulsion flow in porous media. The aim of the present work is to assess the effect of different sea water salinities on w/o emulsion stability through microscopic imaging. Therefore, w/o emulsions were prepared with different sea water samples, which were synthesized to resemble Persian Gulf, Mediterranean, Red Sea, and North Sea water samples. The results showed that log-normal distribution function predicts very well the experimental data to track the... 

The performance of CO2 injection into a semi-heavy oil reservoir was investigated at reservoir conditions, using highly permeable sandstone in a complete series of PVT tests and coreflooding experiments. Analysis of involved parameters such as: injection rate, injectant type and reservoir pressure were also considered. Oil viscosity reduction and oil swelling are the most influential mechanisms of enhanced oil recovery in this process. The results demonstrated that CO2 injection would decrease the interfacial tension for the high permeable medium in the absence of capillarity, but this reduction may not improve the recovery drastically. One of the main important aspects of this work is the... 

Most of the heavy oil reservoirs contain discontinuous shale which affects fluid flow through porous media as well as recovery efficiency during enhanced oil recovery processes. However, the role of shale geometrical characteristics (including orientation, length, discontinuity, and spacing of the shale) on oil recovery remains a topic of debate in the literature, especially during miscible injection of heavy oils and five-spot systems. Here, a series of hydrocarbon solvent injection tests have been performed on various five-spot glass micromodels containing barriers which are initially saturated with heavy oil under fixed flow rate conditions. Oil recoveries as a function of pore volumes of... 

The concern over fossil energy shortage for the next decade leads to the extensive research activities in the area of enhanced oil recovery. Steam injection as one of well known EOR process has been used for about five decades to improve the oil production rate and recovery efficiency. Steam flooding is applied to heavy and extra-heavy oil reservoirs; however it could be used in light oil reservoirs in which water injection do not work effectively. Regardless of different performances, this method is an efficient EOR process for both heavy and light oil reservoirs. In this work, two separate numerical models were prepared to investigate steam flooding performance for the recovery of light... 

The In-Situ Combustion (ISC) as a thermal EOR process has been studied deeply in heavy oil reservoirs and is a promising method for certain non-fractured sandstones. However, its feasibility in fractured carbonates remained questionable. The aim of the present work was to understand the recovery mechanisms of ISC in fractured models and to evaluate the effect of fractures geometrical properties such as orientation, density, location and networking on the ISC recovery performance. Combustion parameters of a fractured low permeable carbonate heavy oil reservoir in Middle East called KEM; applied to simulation study. Simulator has been validated with KEM combustion tube experimental data and... 

The Steam Assisted Gravity Drainage (SAGD) process, a developed Enhanced Oil Recovery (EOR) process to recover oil and bitumen, has been studied theoretically and experimentally in conventional reservoirs and models and is found a promising EOR method for certain heavy oil reservoirs. In this work simulation studies of the SAGD process were made on different fractured models consisting of fractures in both Near Well Region (NWR) and Above Well Region (AWR) and even in the presence of networked fractures. At early stage of the SAGD process in fractured system, steam moves through the fractures first and then the matrix blocks are heated primarily by conduction and possibly some steam...