Sharif Digital Repository

A 0.15% C-1.2% Si-1.7% Mn steel was intercritically annealed at 780 °C for 5 min and then isothermally held at 400 °C for 4 min followed by oil quenching to room temperature and the annealed microstructure consist of 75% ferrite, 15% bainite and 10% retained austenite was produced. Samples of this steel with triple phase structure were tensile tested at temperature range of 25-450 °C. Stress-strain curves showed serration flow at temperature range of 120-400 °C and smooth flow at the other temperatures. All of the stress-strain curves showed discontinuous yielding at all testing temperatures. Both yield and ultimate tensile strength decreased with increasing temperature, but there exists a... 

CdS nanoparticles were grown using CdSO4 and Na 2S2O3 as the precursors and thioglycerol (TG) as the capping agent. TG was shown to exhibit a catalytic role in the reaction and also acted as a capping agent. It was demonstrated that size growth is linearly related to the temperature of the reaction, i.e.the sizes can be controllably adjusted by temperature. The crystalline phase of the nanocrystals was also dependent on the temperature of growth: higher temperature favours the cubic phase. The pH also plays an important role in nanoparticle growth, as lower pH leads to a higher release rate of sulfur species. At pH as high as 10, the growth rate remains slow even at boiling temperature. This... 

The effective compton cross section in a non-degenerate plasma (n≪{((kT/c)2 + 2mkT)/h2}3/2) is investigated in a wide range of temperatures. The results show a decreasing behavior with temperatures especially for kT ≫ mec2. The results may be important in phenomena like accretion discs or ultra-relativistic blast waves in GRB models, where the emitted radiation has to pass through a medium containing high-energy electrons. © 2004 Elsevier Ltd. All rights reserved  

Density currents are continuous currents which move down-slope due to the fact that their density is greater than that of ambient water. The density difference is caused by temperature differences, chemical elements, dissolved materials, or suspended sediment. Many researchers have studied the density current structures, their complexities and uncertainties. However, there is not a detailed 3-D turbulent density current data set perfectly. In this work, the structure of 3-dimensional salt solution density currents is investigated. A laboratory channel was used to study the flow resulting from the release of salt solution into freshwater over an inclined bed. The experiments were conducted... 

A red pigment has been prepared by substituting chromium ions in aluminum ion sites in YAlO3 perovskite structure. In a first step, effect of various mineralizers on YAlO3 formation has been investigated, which resulted in decrease of formation temperature down to 1400 °C. In the next step, a red pigment corresponding to YAl1-yCryO3 (y = 0.05), has been prepared by heating a mixture containing Y2O3, Al2O3 and Cr2O3 at 1500 °C for 6 h. Later, effect of the doped chromium amount on the pigment redness (a*) has been studied. The highest redness has been obtained when y was 0.04(YAl1-yCryO3). Application of the prepared red pigment in low and high temperature glazes, demonstrated its high... 

Dual phase steels with different martensite volume fraction and morphology were tensile tested at temperature range of 25-550 °C. Stress-strain curves of all steels showed serration flow at temperature range of 250-450 °C and smooth flow at the other temperatures. Both yield and ultimate tensile strengths increased with increasing testing temperature up to about 450 °C and then decreased at higher temperatures. At a given temperature, yield stress, tensile strength, and work hardening increased with increasing volume fraction of martensite. Similar behavior was observed by changing martensite morphology from network to fibrous martensite. The change in mechanical properties was related to... 

Dual-phase steels with different morphology and volume fraction of martensite were deformed between 2% and 8% at a high-temperature range of 150-450 °C. Room-temperature tensile properties showed that both yield and tensile stresses depend on the amount of pre-strain, deformation temperature, volume fraction and morphology of martensite. Results show that both YS and UTS increase with increasing the amount of pre-strain at a given temperature. © 2005 Elsevier B.V. All rights reserved  

We consider the Ising model on the edge dual of uncorrelated random networks with arbitrary degree distribution. These networks have a finite clustering in the thermodynamic limit. High- and low-temperature expansions of Ising model on the edge dual of random networks are derived. A detailed comparison of the critical behavior of Ising model on scale free random networks and their edge dual is presented. © 2004 The American Physical Society  

Baseboard heaters are a type of building heating systems that are placed along the base of the interior wall, instead of the traditional skirting. Baseboard heaters meet all the requirements of modern buildings such as thermal comfort, well-architected appearance, space-saving, efficient energy consumption, and fast thermal response. In the present study, we investigate the enhancement of the thermal output of hydronic baseboard heaters. For this purpose, several novel fin-tube arrays such as convector fins and fin-clips are proposed and the thermal performance of each array is evaluated experimentally. In addition, two different types of materials for the tubes, namely, copper and aluminum... 

A new innovative 'universal' structural joint with multiple applications was devised. The two major conceived contexts for the use of this joint are 'joining beams to columns, ' and 'joining diagonal braces to horizontal ones. ' The main features of this joint are its high rotational capacity, its high shear deformation capacity, its high energy-dissipation capacity, its ability to contain damage, and its repalceability. Due to its geometry, it can well lend itself to protection measures against fire, normally practiced by the involving industries. This makes it a good candidate for being used in structures related to oil and gas industry, offshore or onshore. Through numerical modelling of... 

The effects of graphite content on the density and oxidation behavior of MgO-C refractory samples were studied. The samples were formulated with various amounts of graphite and their oxidation behavior was investigated (in an isothermal condition); using a Thermo Gravimetric system (TG), in air and at temperatures ranging from 900"C to 1450"C. The preliminary results showed that the porosity and density of tempered samples were decreased when the graphite content was increased. However, after heating the samples at higher temperatures, the decreasing rate of porosity was lowered. At the beginning of the oxidation process, the rate of weight loss was high, but was gradually decreased when the... 

According to the latest report from the World Health Organization, an estimated 265,000 deaths still occur every year as a direct result of burn injuries. A widespread range of these deaths induced by burn wound happens in low- and middle-income countries, where survivors face a lifetime of morbidity. Most of the deaths occur due to infections when a high percentage of the external regions of the body area is affected. Microbial nutrient availability, skin barrier disruption, and vascular supply destruction in burn injuries as well as systemic immunosuppression are important parameters that cause burns to be susceptible to infections. Topical antimicrobials and dressings are generally...