Sharif Digital Repository

The improvement of the quality of the hole transporting layer (HTL) plays a key role in the fabrication of highly efficient and stable perovskite solar cells (PSCs). Here, we used rubrene as a surface treatment agent on top of a spiro HTL. We found that rubrene can cover the pinholes of the spiro layer and provide an excellent contact layer for planar PSCs. Based on this modification, mobile gold ions from the metal electrode are prevented from diffusing through the HTL hindering the degradation of PSCs. The optimized device shows a maximum power conversion efficiency (PCE) of 19.87% and a 79% fill factor (FF), which are higher than the 17.98% PCE and 72% FF of the reference device. In... 

Perovskite solar cells have been constructed under the standard procedure by employing soluble tetratriphenylamine-substituted Zn phthalocyanine as hole transporting material. Solution processed device construction was carried out under ambient conditions of 50–60% ambient humidity. Triphenylamine substitution played the double role of imparting solubility to the core metal phthalocyanine as well as to introduce electron-rich ligands, which could enhance the role of Zn phthalocyanine as hole transporter. Indeed, the obtained material was functional. The present data highlight tetratriphenylamine-substituted Zn phthalocyanine as hole transporting material but also highlight the importance of... 

Copper phthalocyanine can effectively act as alternative small molecule hole transporting material in perovskite solar cells. In order to produce solution processed devices, a soluble copper phtalocyanine has been synthesized by n-butyl substitution and it was compared to commercially available tert-butyl substituted copper phthalocyanine. It was found that the configuration of the butyl chain plays a very important role in film conductivity and in the subsequent efficiency of solar cells, n-bytyl derivative being the most effective hole transporter. Such a result is due to the fact that n-butyl derivative allows better packing of the molecules in the film and stronger π-π interaction  

Perovskite solar cells (PSCs) are one of the most promising emerging energy-conversion technologies because of their high power conversion efficiencies (PCEs) and potentially low fabrication cost. To improve PCE, it is necessary to develop PSCs with good interfacial engineering to reduce the trap states and carrier transport barriers present at the various interfaces of the PSCs' architecture. This work reports a facile method to improve the interface between the perovskite absorber layer and the hole transport layer (HTL) by adding a small amount of acetonitrile (ACN) in the Spiro-OMeTAD precursor solution. This small amount of ACN dissolves the surface of the perovskite layer, allowing the... 

Copper indium selenide CuInSe2(CISe) thin films were deposited by chemical spray pyrolysis (CSP) method of CuInS2(CIS) and subsequent selenization process. To study the effects of solution concentration, we prepared different precursors solution of CIS including different amount of indium salts from 0.025 to 0.100 M with In/Cu 1.25 and S/In 4. These results propose that solution concentration is critical for inflecting the morphological, optical, electrical, and electrochemical characteristics of solution-processed CISe films and device performance. The studied morphological properties of deposited samples were homogenous, crack-free with large grains in indium salt concentrations more than... 

Herein, a new dopant-free organic material, PV2000, as a stable hole transporting layer (HTL) for the fabrication of stable and efficient perovskite solar cells (PSCs) is introduced. For this purpose, planar PSCs using a triple-A cation perovskite composition are fabricated and the commonly used 2,2′,7,7′-tetrakis[N,N-di(4-methoxyphenyl)amino]-9,9′-spirobifluorene (spiro-OMeTAD) HTL is replaced by dopant-free PV2000 polymer. The characterization results disclose that the PV2000 has a great thermal stability, good hole mobility, and suitable band alignment that matches well with the valence band of triple-A cation perovskite. After proper optimization of PV2000 film thickness, a planar PSC... 

Copper indium selenide CuInSe2(CISe) thin films were deposited by chemical spray pyrolysis (CSP) method of CuInS2(CIS) and subsequent selenization process. To study the effects of solution concentration, we prepared different precursors solution of CIS including different amount of indium salts from 0.025 to 0.100 M with In/Cu 1.25 and S/In 4. These results propose that solution concentration is critical for inflecting the morphological, optical, electrical, and electrochemical characteristics of solution-processed CISe films and device performance. The studied morphological properties of deposited samples were homogenous, crack-free with large grains in indium salt concentrations more than... 

First principles density functional theory (DFT)-based molecular dynamics (MD) is used to study some physical and electronic properties of amorphous silicon (a-Si) samples, as-quenched and annealed containing dangling and floating bonds (pertinent to the threefold- and fivefold-coordinated defects, respectively) as well as distorted tetrahedral bonds. Surprisingly, except for the work of Pantelides (1986) who gave a rough estimate for the effective electron correlation energy, Ueff of a floating bond on the fivefold-coordinated Si, to date, there are no theoretical studies in the literature for the calculation of Ueff pertinent to this type of defect. In this work, Ueff for each type of... 

Perovskite solar cells have been constructed under ambient conditions by using 2,2',7,7'-Tetrakis-(N,N-di-4-methoxyphenylamino)-9,9'-spirobifluorene (spiro-OMeTAD) mixed with a small quantity of soluble tetra-n-butyl substituted copper phthalocyanine as hole transporting material. The introduction of the phthalocyanine derivative resulted in an impressive increase of cell efficiency, which changed from 10.4% in the absence to 15.4% in the presence of phthalocyanine. This effect is related to the creation of deep traps in the hole transporting phase which block back-travelling electrons as well as to the improvement of the structural quality of the spiro-OMeTAD film in the presence of... 

Perovskite solar cells have been constructed under ambient conditions by using 2,2',7,7'-Tetrakis-(N,N-di-4-methoxyphenylamino)-9,9'-spirobifluorene (spiro-OMeTAD) mixed with a small quantity of soluble tetra-n-butyl substituted copper phthalocyanine as hole transporting material. The introduction of the phthalocyanine derivative resulted in an impressive increase of cell efficiency, which changed from 10.4% in the absence to 15.4% in the presence of phthalocyanine. This effect is related to the creation of deep traps in the hole transporting phase which block back-travelling electrons as well as to the improvement of the structural quality of the spiro-OMeTAD film in the presence of... 

Organometal halide perovskite solar cells have been constructed using soluble tetra-n-butyl-copper phthalocyanine as hole transporting material. Devices were constructed and characterized under ambient conditions of 50–60% ambient humidity. Soluble copper phthalocyanine gave a modest PCE of 7.3% but when a buffer layer of either Al2O3 or graphene oxide was introduced between the perovskite and the hole transporting layer the cell efficiency extensively increased and reached 14.4% in the presence of graphene oxide. Corresponding data obtained by employing the standard spiro-OMeTAD as hole transporter gave equivalent performance. Combination then of tetra-n-butyl-copper phthalocyanine with... 

Thin-film solar cells based on hybrid organo-halide lead perovskites achieve over 22% power conversion efficiency (PCE). A photovoltaic technology at such high performance is no longer limited by efficiency. Instead, lifetime and reliability become the decisive criteria for commercialization. This requires a standardized and scalable architecture which does fulfill all requirements for larger area solution processing. One of the most highly demanded technologies is a low temperature and printable conductive ink to substitute evaporated metal electrodes for the top contact. Importantly, that electrode technology must have higher environmental stability than, for instance, an evaporated silver... 

CH3 NH3 PbI3 (MAPbI3) thin film solar cells, which are reported at laboratory efficiency scale of nearly 22%, are the subject of much attention by energy researchers due to their low cost buildup, acceptable efficiency, high absorption coefficient and diffusion length. The main purpose of this research is to simulate the structure of thin film perovskite solar cells through numerical simulation of SCAPS based on the empirical data for different hole transport layers. After simulating the initial structure of FTO/TiO2/CH3NH3PbI3/Spiro-OMeTAD solar cell, the hole transport layer Spiro-OMeTAD thickness was optimized on a small scale using modeling. The researchers also sought to reduce the... 

The effect of substitutional Li doping into NiOx hole transporting layer (HTL) for use in inverted perovskite solar cells was systematically studied. Li doped NiOx thin films with preferential crystal growth along the (111) plane were deposited using a simple solution-based process. Mott-Schottky analysis showed that hole carrier concentration (NA) is doubled by Li doping. Utilizing 4 % Li in NiOx improved the power conversion efficiency (PCE) of solar devices from 9.0 % to 12.6 %. Photoluminescence quenching investigations demonstrate better hole capturing properties of Li:NiOx compared to that of NiOx, leading to higher current densities by Li doping. The electrical conductivity of NiOx is... 

Previous studies on wireless sensor networks indicate one of the most important research topics is to consider both significance of the reduction in sensor nodes energy consumption and improving network lifetime. Regarding results of some researchers using sinks, mobility has a substantial impact on the performance of sensor networks concerning reducing total energy consumption, increasing the number of active nodes and solving the energy-hole problem. In this study, we consider hexagons beehives feature where sensor nodes are distributed across a hexagon randomly. This hexagonal is divided into equal clusters based on the radius of hexagonal. Also, the need for cluster heads to be close to... 

N-annulated perylene based materials show outstanding and tunable optical and physical properties, making them suitable to be charge transport materials for optoelectronic applications. However, this type of materials has so far not been well studied in solar cells. Here, we develop a new hole transport material (HTM), namely S5, based on perylene building block terms, for organic-inorganic hybrid perovskite solar cells (PSCs). We have systematically studied the influences of the film thickness of S5 on their photovoltaic performance, and a low concentration of S5 with a thinner HTM film is favorable for obtaining higher solar cell efficiency. S5 shows excellent energy alignment with... 

Carbazole compounds are p-type hole-transporting materials (HTMs) useful for perovskite solar cells (PSCs). In this work, we developed a new class of carbazol based HTMs; non-fused 3-D asymmetric structures (S14 and S12) as HTM of PSCs. To the best of our knowledge, there is no report on non-fused HTMs with a high glass transition temperature (Tg = 165 °C), which reduces crystallization and suppresses grain boundaries in glassy film, resulting in long-term durability. Experimental results show that tuning the carbazole moiety in S14 structure has a constructive influence on geometrical alignment, hole mobility, hydrophobicity, stability as well as efficiency. The resultant power conversion... 

Inorganic hole-transport materials (HTMs) have been frequently applied in perovskite solar cells (PSCs) and are a promising solution to improve the poor stability of PSCs. In this study, we investigate solution-processed copper indium gallium disulfide (CIGS) nanocrystals (NCs) as a dopant-free inorganic HTM in n-i-p type PSCs. Moreover, Cs0.05(MA0.17-FA0.83)0.95Pb(I0.83Br0.17)3 mixed-halide perovskite with proper crystalline quality and long-time stability was utilized as the light-absorbing layer under ambient conditions. To optimize the cell performance and better charge extraction from the perovskite layer, the Ga concentration in the Cu(In1-XGaX)S2 composition was changed, and the X...