Sharif Digital Repository

Circulation regions always exist in the settling tanks. These regions reduce the tank's performance and decrease effective volume of the tank. Recirculation zones would also result in short-circuiting and high flow mixing problems. Inlet position would also have effect on these, too. Using good baffle configuration may increase performance of settling tanks. One method for comparison of different tanks with each others is to use FTC. In this paper, by using FTC the effects of inlet position and baffle configuration on the hydraulic performance of primary settling tanks are studied. The best position of baffle is also determined. Copyright © 2005 by ASME  

The hydraulic performances of drain pipes are very important in drainage projects and systems. Usually these pipes are used in a saturated soil to decrease the water table to a favorable level or, drain the excess water. However, drain pipes can be used in a water or wastewater tank for different purposes such as selective withdrawal. There are not much published documents on the performance of drain pipes in submerged situations. Therefore, the aim of this study was to examine the performance of drain pipe in a submerged tank. For this, a horizontal pipe of 26.5 mm inner diameter, 5 meter long with 48 circular drain inlets of 10 mm diameter at equal distances along the pipe have been tested... 

Labyrinth side weir is one type of weirs, which can be used when the length of opening is limited. One of the advantages of labyrinth side weir is to increase the effective length of weir perpendicular to the flow and, therefore, diverting more discharge with the same flow depth and weir geometry (opening and height). Discharge coefficient should be determined to investigate the weir performance and estimate the discharge passing over the weir. In this paper, hydraulic performance of labyrinth side weir with asymmetric geometry has been experimentally studied. The change to the geometry of ordinary labyrinth side weirs causes an increase in the effectiveness of the length of weir as being... 

The capability level of rotary as well as first generation drilling operation could not be matched for deeply drilling programs. To reach that deep, the increasing in drill string length could also cause an additional constraint on hydraulic performance. The operation of slim hole drilling has significant potential to reduce well costs. This cost might be savings are especially important with increased demand for reduced capital finance under current economic conditions in the Iranian oil and gas industry. This savings achievement could be caused by use of smaller drilling rigs, work over rigs, reduced casing size, reducing requirement for drilling consumables and other costs associated with... 

In the present study, methods for improving the hydraulic performance of labyrinth side weirs in a rectangular channel are reported based on model experimentation. For this purpose different arrangements and configurations of groups of guide vane plates and piles in the side weir flow field were tested. Experiments were conducted on labyrinth side weirs of different lengths and sill heights fitted in the test section of a rectangular glass-walled channel. Depths of flow were measured in both longitudinal and crosswise directions at regular intervals and their profiles were studied. It was found that the discharge coefficient of the labyrinth side weirs under these conditions gave... 

One of emerging advanced fuel materials for the next generations of the nuclear reactors is Fully Ceramic Microencapsulated (FCM) fuel. FCM fuel structure is comprised of TRISO particles dispersed randomly in a SiC matrix. In the present study, the thermal hydraulic performance of a SMART reactor is investigated and the results are compared with the case that conventional UO2 fuel is loaded into the core. At the beginning of the cycle, the reactor is simulated in normal operational and transient conditions. MCNPX 2.6 stochastic code is utilised to calculate neutronic parameters. COMSOL and RELAP5 codes are used for thermal hydraulic analysis. The reactor dynamics is simulated based on... 

In this study, a novel type of LHP is innovated, fabricated, and its performance is assessed by numerous experiments. Compared to conventional LHPs, this novel design has some modifications in its evaporator and reservoir configuration. This particular type has a simpler and less costly fabrication procedure compared to other LHPs and it yields acceptable performance. Additionally, a novel method is introduced to control the temperature distribution in the system. A steel ball is placed in the evaporator to actively control the operating temperature. The ball is moved by two magnets installed outside of the evaporator. Moreover, a steady-state one-dimensional mathematical model of the... 

A numerical analysis has been performed to investigate the flow structure and thermal hydraulic performance of turbulent flow through circular tube equipped with twisted tapes with different cut shapes. The geometries of cuts are rectangular with different cut ratios 0.25