Sharif Digital Repository

Asphaltene precipitation problems manifest themselves in different stages of oil reservoirs production. Experimental and modeling investigations are, therefore, employed as promising tools to assist in predictions of asphaltene precipitation problems and selection of proper production facilities. This study concerns experimental and modeling investigations of asphaltene precipitation during natural production and gas injection operations for a heavy Iranian crude oil at reservoir conditions. First, with design and performance of high pressure-high temperature experiments, asphaltene precipitation behavior is comprehensively investigated; the effects of pressure and temperature are fully... 

Embryogenesis, regeneration and cell differentiation in microbiological entities are influenced by mechanical forces. Therefore, development of mechanical properties of these materials is important. Neural network technique is a useful method which can be used to obtain cell deformation by the means of force-geometric deformation data or vice versa. Prior to insertion in the needle injection process, deformation and geometry of cell under external point-load is a key element to understand the interaction between cell and needle. In this paper the goal is the prediction of cell membrane deformation under a certain force, and to visually estimate the force of indentation on the membrane from... 

Minimum Miscibility Pressure (MMP) is regarded as one of the foremost parameters required to be measured in a CO2 injection process. Therefore, a reasonable approximation of the MMP can be useful for better development of injection conditions as well as planning surface facilities. In this study, the impact of asphaltene content ranging from 3.84 % to 16 % on CO2/heavy oil MMP is evaluated. In this respect, slim tube miscibility and Vanishing Interfacial Tension (VIT) tests are used. Regarding the VIT test, the Interfacial Tension (IFT) is measured by means of two methods including pendant drop and capillary apparatuses, and thereafter the MMP measurement error between slim tube and VIT... 

In recent years, polysilicon nanoparticles are used to enhance the oil recovery through the water injection process in oilfields. The contributing mechanisms are the reduction of interfacial tension and wettability alteration which lead to improving or decreasing the oil phase relative permeability and can be traced by change of relative permeability curves. However, profound understanding of the effect of dispersed nano-silica particles on the hysteretic behavior of relative permeability curves remains a controversy topic in the literature.The current study illustrates the influence of dispersed silica particles on hysteretic trend of two-phase curves of oil-water relative permeability.... 

Nitrogen has emerged as a competitive gas injection alternative for gas-based enhanced oil recovery processes in the past two decades. The injection of nitrogen into the reservoirs has improved the oil recovery efficiency in various oil reservoirs from heavy to volatile oils. As it is known, interfacial tension (IFT) plays a key role in any enhanced oil recovery process, particularly gas injection processes; therefore, its accurate determination is crucial for the design of any gas injection process especially at reservoir condition. In this study, an axisymmetric drop shape analysis (ADSA) was utilized to measure the equilibrium IFTs between crude oil and N2 at different temperature levels... 

Steam injection process has been considered for a long time as an effective method to exploit heavy oil resources. Over the last decades, Steam Assisted Gravity Drainage (SAGD) has been proved as one of the best steam injection methods for recovery of unconventional oil resources. Recently, Fast-SAGD, a modification of the SAGD process, makes use of additional single horizontal wells alongside the SAGD well pair to expand the steam chamber laterally. This method uses fewer wells and reduces the operational cost compared to a SAGD operation requiring paired parallel wells one above the other. The efficiency of this new method in naturally fractured reservoir is not well understood.... 

This work is concerned with the role of geometrical properties of fractures on oil displacement efficiency during solvent injection to heavy oil. Here, a series of solvent injection processes were conducted on one-quarter five-spot fractured micromodels that were initially saturated with the heavy oil, at a fixed flow rate condition. The oil recovery was measured using image analysis of the continuously provided pictures. The results show that for the range of experiments performed here, the maximum oil recovery happens at a fracture orientation angle of 45 degrees. Also, increasing the number of fractures leads to a higher oil recovery factor by solvent in 45 degrees, while it does not... 

The application of the renewable energy sources, especially solar energy, for thermal enhanced oil recovery methods as an economical and environmental valuable technique has received many attractions recently. Concentrated Solar Power systems are capable of producing substantial quantities of steam by means of focused sunlight as the heat source for steam generation. This paper aims to investigate viability of using this innovative technology in fractured reservoirs to generate steam instead of using conventional steam generators. A synthetic fractured reservoir with properties similar to those of giant carbonate oil reserves in the Middle East was designed by using commercial thermal... 

Water shielding phenomenon generally occurs after waterflooding in water-wet rocks, and impedes direct contact between the oil and the injected gas in tertiary gas injection processes. In this work, a set of visualization experiments were performed on micromodel patterns including designed dead-end pores with a film of water on the surface of pore bodies, which is a more realistic representation of porous media. The experiments were conducted at different miscibility conditions, and the required time for water to be displaced from the throat by the swelling of oil was measured for first contact miscible (n-C5/CO2) and immiscible (n-C10/CO2) systems. In the next step, a model was proposed to... 

To study the gas injection scenario for successful implementation of enhanced oil recovery (EOR)processes, the prediction of interfacial tension (IFT)between injected gas and the crude oil is of paramount significance. In the present study, some intelligent methods were developed for determining IFT values between supercritical CO2 and normal alkanes. IFT was considered as a function of temperature, pressure, and molecular weight of normal alkanes. The developed methods were Multilayer perceptron (MLP), Genetic Algorithm Radial Basis Function (GA-RBF), and Conjugate Hybrid-PSO ANFIS (CHPSO-ANFIS). The average absolute percent relative errors (AAREs)for the stated techniques were found to be... 

In this study, the main recovery mechanisms behind oil/water/gas interactions during the water-alternating-gas (WAG) injection process, in a network of matrix/fracture, were fundamentally investigated. A visual micromodel was utilized to provide insights into the potential applications of WAG process in fractured oil-wet media as well as the possibility of observing microscopic displacement behavior of fluids in the model. The model was made of an oil-wet facture/matrix network system, comprised of four matrix blocks surrounded with fractures. Different WAG injection scenarios, such as slug arrangements and the effects of fluid injection rates on oil recovery were studied. A new equation... 

This study concerns with the microscopic and macroscopic fluid distribution and flow behavior during water alternating solvent (WAS) injection process to heavy oil using micromodel generated from thin section of a real rock which has rarely attended in the available literature. In this study, a one-quarter five-spot glass micromodel was deployed to examine the effect of flow media topology on microscopic displacements as well as macroscopic efficiency of WAS process. The micromodel was initially saturated with the heavy oil, and then the hydrocarbon solvent and water were injected alternately into it. The observations confirmed that WAS injection scheme is an effective method for the...