Sharif Digital Repository

Undoped and copper doped nanostructured zinc oxides were synthesized by using a series of synthetic layered material, undoped and copper doped zinc hydroxide nitrates at various molar percentages of copper (2-10) within the layers as precursors. The layered materials were heat-treated at 500 °C to produce zinc oxide nanostructures with crystallite sizes in the range of 23-35 nm. Optical studies of the nanostructured copper doped zinc oxides showed the decrease in band gap with increasing content of the doping agent, copper  

The hybrid rocket motor is a kind of chemical propulsion system that has been recently given serious attention by various industries and research centers. The relative simplicity, safety and low cost of this motor, in comparison with other chemical propulsion motors, are the most important reasons for such interest. Moreover, throttle-ability and thrust variability on demand are additional advantages of this type of motor. In this paper, the result of an internal ballistic simulation of hybrid rocket motor in a zero-dimensional form is presented. Further to validate the code, an experimental setup was designed and manufactured. The simulation results are compared with the experimental data... 

High silicon fly ash (HSFA) utilized as a source of silicon in synthesizing of Na-A, -X and -Y zeolites through alkali fusion followed by hydrothermal treatment at 100 °C for 12 h. Various types of zeolites with different degrees of purity were prepared by changing Si/Al ratio of the reaction mixture from 1.6 to 3.0. In addition, exact boundaries of this ratio for synthesis of each zeolite type were determined. Furthermore, the effect of NaOH amount utilized in alkaline fusion step on crystalinity of samples investigated. The synthesized zeolites were characterized using various techniques including; XRD, TGA, FTIR, SEM and BET. The ion-exchange behaviors of zeolitic samples tested with... 

An improved and efficient method for the synthesis of 1- & 5-substituted 1Htetrazole derivatives was described in the presence of nano-ordered MCM-41-SO3H as an effective heterogeneous catalyst. This metal-free protocol, [2 + 3] cycloaddition of sodium azide to various nitriles or ethyl N-phenyl formimidate intermediate under mild reaction conditions, provides a wide range of 1H-tetrazoles in good to excellent yields. The catalyst was reused five times without significant loss of catalytic activity. © 2019 Sharif University of Technology. All rights reserved  

An improved and efficient method for the synthesis of 1- & 5-substituted 1Htetrazole derivatives was described in the presence of nano-ordered MCM-41-SO3H as an effective heterogeneous catalyst. This metal-free protocol, [2 + 3] cycloaddition of sodium azide to various nitriles or ethyl N-phenyl formimidate intermediate under mild reaction conditions, provides a wide range of 1H-tetrazoles in good to excellent yields. The catalyst was reused five times without significant loss of catalytic activity. © 2019 Sharif University of Technology. All rights reserved  

Enhancing the photoresponse of single-layered semiconductor materials is a challenge for high-performance photodetectors due to atomically thickness and limited quantum efficiency of these devices. Band engineering in heterostructure of transition metal chalcogenides (TMDs) can sort out part of this challenge. Here, we address this issue by utilizing the plasmonics phenomenon to enrich the optoelectronics property of the WSe2/MoS2 heterojunction and further enhancement of photoresponse. The introduced approach presents a contamination-free, tunable and efficient way to improve light interactions with heterojunction devices. The results showed a 3600-fold enhancement in photoresponsivity and... 

Magnesium nanopowder (MgNP) of 17 nm average size was produced by planetary ball milling of Mg (φ=229 μm) with 10 wt% NaCl (φ=406 μm) for 50 h. NaCl was omissible by dissolution in saturated KOH. Partial oxidation of MgNP occurred, however, in presence of KOH. MgNP-NaCl mixture was, therefore, used for transmission electron microscopy (TEM), scanning electron microscopy (SEM), x-ray diffraction (XRD), differential scanning calorimetry (DSC) and Sieverts equilibrium investigation. DSC analysis of ammonium perchlorate showed one endothermic and three exothermic reactions. MgNP did not noticeably affect on the initial endothermic reaction. But it decreased transformation temperatures of the... 

Epitaxial cerium oxide (CeO2) buffer layer has been grown on lanthanum aluminate (LAO) single crystal substrates for fabrication of c-axis oriented YBa2Cu3O7-x (YBCO). Precursor solution of cerium acetylacetonates with viscosity of 0.6 centipoises was spin coated on the 1×1 cm area LAO substrates. The calcination was carried out by very slow ramp (1°C per minute) until the final temperature of 500°C in oxygen flow to remove most of the organic compounds. The final heat treatment has been done at 780°C by a ramp of 20° per minute in gas flow of mixed argon-oxygen with 5 Pa partial pressure of oxygen. The thickness of the deposited CeO2 buffer layer was 20 nm. Then, 100 nm thick YBCO film was... 

A green and simple synthesis method based on a two-step chemical vapor deposition approach has been developed to synthesize transition metal dichalcogenides flakes. With non-toxic precursor such as transition metal oxides and elemental sulfur, large-area, strong photoluminescent and uniform MoS2 nanoflakes were produced at a relatively low growth temperature (650 °C). Controlling the layer number and morphology was achieved only by precursor concentration without any oxide impurity revealed by SEM, PL and Raman spectroscopy. This method can be used to make wide range of metal chalcogenides such as ZnS, SnS2, PtS2 and PdS2  

The reaction of the functionalized mesoporous SBA-15 in absolute ethanol with copper (II) acetate afforded a novel CuII-Schiff base/SBA-15 catalyst. The compound CuII-Schiff base/SBA-15 was characterized by IR spectroscopy, small-angle X-ray diffraction (SAX), Energy Dispersive X-ray Spectroscopy (EDXS), X-ray Absorption Near Edge Structure (XANES), Scanning Electron Microscope (SEM), Transmission Electron Microscope (TEM), and N2 adsorption/desorption studies. Further, the catalytic activity of this well-defined material was tested in three-component Copper-catalyzed Azide-Alkyne Cycloaddition (CuAAC) reactions to obtain 1,4-disubstituted-1,2,3-triazoles in good to excellent yields from an... 

Background: Kinetic andmorphological aspects of slurry propylene polymerization using a MgCl2-supported Ziegler-Natta catalyst synthesized from a Mg(OEt)2 precursor are investigated in comparison with a ball-milled Ziegler-Natta catalyst. Results: The two types of catalyst show completely different polymerization profiles: mild activation and long-standing activity with good replication of the catalyst particles for the Mg(OEt)2-based catalyst, and rapid activation and deactivation with severe fragmentation of the catalyst particles for the ball-milled catalyst. The observed differences are discussed in relation to spatial distribution of TiCl4 on the outermost part and inside of the... 

The morphology of the perovskite layer, the effective extraction of the charge carriers, and their transport are the main factors determining the power conversion efficiency (PCE) of the perovskite solar cells (PSCs). In this work, we demonstrated that the geometric and electronic structures of the PSCs could be modified by using a conductive polymer additive in the lead (Pb) halide layer prepared by a two-step deposition method. Polypyrrole (PPy) as a conductive polymer is used in the perovskite layers which could increase the PCE of CH3NH3PbI3-xClx mixed-halide PSCs. By adding an optimized amount of PPy, PCE has been raised from 10.4 to 13.2%. PPy acts as a conductive channel facilitating... 

Stem cell treatment is promising in the various disorders treatment, but its effect is confined by the adverse conditions in the damaged tissues. The utilization of hydrogels has been suggested as a procedure to defeat this issue by developing the engraftment and survival of injected stem cells. Specifically, injectable hydrogels have drawn much attention due to their shape adaptability, ease of use, and the capability to reach body parts that are hard to access. In this study, the thermosensitive injectable hydrogels based on oxidized alginate, gelatin, and carbon nitride quantum dots (CNQDs) have been fabricated for tissue engineering. The mechanical characteristics of the nanocomposite... 

Surface modification of SnO2 electron transporting layer (ETL) plays a critical role in the performance of SnO2-based planar perovskite solar cells (PSC). Here, we show how long-time NH4F-based water bath treatment of SnO2 layer makes smoothing and morphological improvements and enhances the device performance. Recently it was shown that short-time NH4F treatment (2 sec) with spin coating method reduces interface traps by improving surface chemistry. Here we observe the smoothing of SnO2 films as a result of long-time NH4F treatment, which could be a result of a slight etching-deposition process. Absorption and resistivity measurements indicate that SnO2 etching process is involved in... 

CaO derived from calcined eggshell was doped with Na–K by wet impregnation method and the effect of different Na/K molar ratios was investigated on biodiesel production from canola oil. The catalysts were characterized by X-ray Powder Diffraction (XRD), Brunauer–Emmett–Teller (BET), Scanning Electron Microscopy (SEM), Energy Dispersive X-ray (EDX), and Thermogravimetric (TGA) analyses. FAME yields were determined by Gas Chromatography-Mass Spectrometry (GC-MS). The Na–K/CaO catalyst with Na/K molar ratio of 1 showed the highest FAME yield of 97.6% at optimum reaction conditions. Structural investigation of materials revealed that FAME yield was proportional to the number of basic sites on... 

One of the key parts of perovskite solar cells which has great influence on their performance and stability is hole transporting layer. Spiro-OMeTAD is extensively used as organic hole transporting material in perovskite solar cells. However, Spiro-OMeTAD is expensive and has low chemical stability. In this study, the solution processed Sb2S3 and Cu3SbS4 nanocrystals have been synthesized and then the n-i-p mesoscopic perovskite solar cells have been fabricated using Spiro-OMeTAD, Sb2S3 and Cu3SbS4 nanocrystals as hole transporting layer at ambient air condition. It is shown that the conduction and valence band levels of the synthesized Sb2S3 and Cu3SbS4 nanocrystals are in the proper... 

The development of efficient and cost-effective catalysts for the oxygen evolution reaction is highly desirable for applications that are based on sustainable and clean technologies. In this study, we report the synthesis of a series of cerium(iv) oxide and nickel diselenide nanocomposites (NiSe2/CeO2) as efficient electrocatalysts for the oxygen evolution reaction in an alkaline medium. The ratios of the two substances were optimized to reach the highest catalytic activity. The structure and morphology of synthesized materials were investigated by XRD, FE-SEM, EDX, BET, XPS, and TEM techniques. It was observed that the nanocomposite with a 10 : 1 mass ratio of NiSe2to CeO2showed the best... 

In this study, the enhanced trichloroethylene (TCE) degradation performance was investigated by polyvinyl alcohol coated calcium peroxide nanoparticles (PVA@nCP) as an oxidant in Fe(II)-based catalytic systems. The nanoscale iron sulfide (nFeS), having an average particle size of 115.4 nm, was synthesized in the laboratory and characterized by SEM, TEM, HR-TEM along with EDS elemental mapping, XRD, FTIR, ICP-OES, and XPS techniques. In only ferrous iron catalyzed system (PVA@nCP/Fe(II)), TCE degradation was recorded at 58.9% in 6 h. In comparison, this value was increased to 97.5% or 99.7% with the addition of citric acid (CA) or nFeS in PVA@nCP/Fe(II) system, respectively. A comparative... 

In this study, the enhanced trichloroethylene (TCE) degradation performance was investigated by polyvinyl alcohol coated calcium peroxide nanoparticles (PVA@nCP) as an oxidant in Fe(II)-based catalytic systems. The nanoscale iron sulfide (nFeS), having an average particle size of 115.4 nm, was synthesized in the laboratory and characterized by SEM, TEM, HR-TEM along with EDS elemental mapping, XRD, FTIR, ICP-OES, and XPS techniques. In only ferrous iron catalyzed system (PVA@nCP/Fe(II)), TCE degradation was recorded at 58.9% in 6 h. In comparison, this value was increased to 97.5% or 99.7% with the addition of citric acid (CA) or nFeS in PVA@nCP/Fe(II) system, respectively. A comparative... 

Development of renewable energies is in parallel with improving high-performance energy storage devices, which can store maximum solar or wind energy and power. Herein, asymmetric energy storage systems are constructed from phosphorus-doped nickel sulfide (P-doped NiS) and biomass-derived humic acid (HA) as positive and negative electrodes, respectively. Initially, nickel sulfide (NiS) nanostructures are directly grown onto nickel foam (NF) via a hydrothermal step. P-doping into the NiS bulk is carried out through a simple hydrothermal process as well. Also, HA is activated via carbonization treatment (A-HA) for employing as the negative electrode's active material. The P-doped NiS-NF...