Sharif Digital Repository

This paper studies a WAG process for improving the recovery efficiency in light oil reservoirs. Until now, few references have reported the role of CO2 mole percent on recovery improvement in light oil reservoirs. The injected gas was changed, and the effect of composition changes on performance of core flood experiments were conducted at fixed flow rate. Five series of experiments (varied in methane mole percentages, 0, 25, 50, and 75, 100) were systematically examined. The results indicated that the oil recovery efficiency improved with the increasing of CO2 mole ratio and there was also maximum recovery efficiency in this work. That would be helpful to better understanding the role of CO2... 

Asphaltene precipitation and deposition is a serious issue in all facets of petroleum production and processing. Despite the numerous experimental efforts concerning asphaltenes, the effect of temperature on asphaltene precipitation and aggregation in live oils remains an elusive and controversial subject in the available literature. In this work, a series of high pressure-high temperature depressurization experiments were designed to assess the effect of temperature on asphaltene precipitation and aggregation in light live oils. Asphaltene related experiments were performed using a high pressure microscope and high pressure-high temperature filtration setup on a light live oil with a low... 

The main objective of this study is to investigate the effect of temperature on asphaltene destabilisation (precipitation/aggregation) in live oils at elevated pressure conditions. Here, the asphaltene related experiments were performed using solid detection systems, high pressure microscope, and high pressure-high temperature filtration apparatuses in two Iranian light and heavy live oils with different characteristics and stability. The obtained results were interpreted in terms of asphaltene onset pressure, size distribution and average diameter of the aggregates, fractal analysis of the aggregates structures, and the amount of asphaltene precipitation. As well, the results of the... 

The concern over fossil energy shortage for the next decade leads to the extensive research activities in the area of enhanced oil recovery. Steam injection as one of well known EOR process has been used for about five decades to improve the oil production rate and recovery efficiency. Steam flooding is applied to heavy and extra-heavy oil reservoirs; however it could be used in light oil reservoirs in which water injection do not work effectively. Regardless of different performances, this method is an efficient EOR process for both heavy and light oil reservoirs. In this work, two separate numerical models were prepared to investigate steam flooding performance for the recovery of light... 

Many oil reservoirs encounter asphaltene precipitation as a major problem during natural production. In spite of numerous experimental studies, the effect of temperature on asphaltene precipitation during pressure depletion at reservoir conditions is still obscure in the literature. To study their asphaltene precipitation behavior at different temperatures, two Iranian light and heavy live oil samples were selected. First, different screening criteria were applied to evaluate asphaltene instability of the selected reservoirs using pressure, volume, and temperature data. Then, a high pressure, high temperature filtration (HPHT) setup was designed to investigate the asphaltene precipitation... 

This work concerns with experimental investigation of CO2 WAG injection to light crude oil in near miscible conditions which has been rarely attended in the available literature. Here, several core flood experiments at three constant injection rates and four WAG ratios are conducted on sandstone rocks saturated with light crude oil in presence of saline water. The results showed that higher injection rate has a better performance regarding oil recovery for smaller PVs of injected fluids, while lower injection rate showed higher ultimate recovery for a 30% increase in injected PVs. Secondary continuous gas injection showed a superior performance than all the other WAG injections in different... 

In this work effect of composition changes of injection gas, CH4 + CO2, on the performance of immiscible WAG injection in light oil, 41 oAPI, which has been rarely attended in the available literature is investigated. Presence of CO2 helps to reduce the MMP of CH4 significantly. Core flood experiments are conducted at reservoir conditions and fixed flow rate of 0.5cc/min on a sandstone sample with the brine concentration of 5000 ppm, and the influence of injection gas composition as well as WAG ratio on oil recovery is investigated. Different mole percents of methane in mixture, 0%, to 100% are examined, and the tests continued to ten alternate cycles with a slug size of 0.1 pore volumes and... 

To meet stringent emission standards stipulated by regulatory agencies, the oil industry is required to bring down the sulfur content in fuels. Oil supplies 38% of the worldwide energy, and as the light oil is limited and meanwhile the energy demand is increasing, it is a must to use heavy crude oil and therefore desulfurize it to meet environmental standards. As it is not feasible to desulfurize all the sulfur containing compounds of heavy crude oil by the existing methods (such as hydro-desulfurization) we have focused on biodesulfurization of heavy crude oil. We have isolated the first native fungus which has been identified as Stachybotrys sp. and is able to remove sulfur and nitrogen... 

This work concerns the experimental investigation of surfactant alternating CO 2 injection in carbonate rocks. The core samples provided from a low-temperature fractured light oil reservoir, located in southwest Iran. The experiments were designed to observe the effect of CO 2-foam injection on gas mobility and oil recovery at different surfactant concentrations. The core samples were initially saturated with synthetic/field brine, 5,000 ppm, and then flooded with live oil to reach connate water saturation at reservoir condition, 115F and 1,700 psia. The commercial surfactant used was sodium lauryl sulfate as an anionic surfactant. The results of this work, along with field-scale simulation...