Sharif Digital Repository

Dual-phase steels with different morphology and volume fraction of martensite were deformed between 2% and 8% at a high-temperature range of 150-450 °C. Room-temperature tensile properties showed that both yield and tensile stresses depend on the amount of pre-strain, deformation temperature, volume fraction and morphology of martensite. Results show that both YS and UTS increase with increasing the amount of pre-strain at a given temperature. © 2005 Elsevier B.V. All rights reserved  

In this article, we investigated the effect of martensite morphology on the mechanical properties and formability of dual phase steels. At first, three heat treatment cycles were subjected to a low-carbon steel to produce ferrite–martensite microstructure with martensite morphology of blocky-shaped, continuous, and fibrous. Tensile tests were then carried out so as to study mechanical properties, particularly the strength and strain hardening behavior of dual phase steels. In order to study the formability of dual phase samples, Forming Limit Diagram was obtained experimentally and numerically. Experimental forming limit diagram was obtained using Nakazima forming test, while Finite Element... 

Carbide morphologies of white cast iron containing 22% Cr and 10-12% tungsten with different carbon contents (2.34-3.20. wt.%) were investigated. Results indicated that for the as-cast alloys with no heat treatments, the addition of carbon changes the morphology of carbides during air-cooling in the presence of tungsten. Light microscopy analysis revealed that for an alloy with 2.3. wt% carbon, chromium carbides possess coarse gray appearance (GA). Increasing the carbon content reduced the coarse GA zones volume fraction while a finer GA zones emerged. The coexistence of coarse and fine GA phases came to an end at 2.8. wt% carbon, at which only fine GA zones spread throughout the chromium... 

Dual phase (DP) steels with network and fibrous martensite were produced by intercritical annealing heat treatment cycles. Some of these steels were deformed at dynamic strain aging temperatures. Room temperature tensile tests of specimens deformed at 300 °C showed that both yield and ultimate tensile strengths for both morphologies increased, while total elongation decreased. Fatigue test results before and after high temperature deformation showed that dynamic strain aging has a stronger effect on fatigue properties of dual phase steels with fibrous martensite. Cracks in DP steels with fibrous martensite propagate in a tortuous path in soft ferrite phase, while they pass of both hard and... 

In this article, we investigated the effect of martensite morphology on the mechanical properties and formability of dual phase steels. At first, three heat treatment cycles were subjected to a low-carbon steel to produce ferrite–martensite microstructure with martensite morphology of blocky-shaped, continuous, and fibrous. Tensile tests were then carried out so as to study mechanical properties, particularly the strength and strain hardening behavior of dual phase steels. In order to study the formability of dual phase samples, Forming Limit Diagram was obtained experimentally and numerically. Experimental forming limit diagram was obtained using Nakazima forming test, while Finite Element... 

This paper presents the effect of martensite volume fraction (VM) on mechanical properties of AISI 4340 steel with ferrite-bainite-martensite microstructures. The steel bars were austenitized at 900°C for 1h followed by intercritical annealing at 740°C for 100min and quenching into a salt bath with temperature of 300°C and holding at different times to obtain triple phase (TP) microstructures with 34vol.% fraction ferrite and various martensite (or bainite) contents. Presence of three phases in adjacent to each other was confirmed by metallographic analysis and TEM studies. TEM observation also indicates higher density of dislocations within ferrite near martensite colonies compared to that... 

Dual phase steels (DPS)s have a microstructure consisting of a hard second phase called Martensite in the soft Ferrite matrix. In recent years, there has been interest in dual-phase steels, because the application of these materials has made significant usage; particularly in the automotive sector Composite microstructure of (DPS)s exhibit interesting characteristic mechanical properties such as continuous yielding, low yield stress to tensile strength ratios(YS/UTS), and relatively high formability; which offer advantages compared with conventional high strength low alloy steels(HSLAS). The research dealt with the characterization of damage in (DPS)s. In this study by review the mechanisms...