Sharif Digital Repository

This paper focuses on multi-objective optimisation (MOO) to optimise the planar solid oxide fuel cell (SOFC) stacks performance using a genetic algorithm. MOO problem does not have a single solution, but a complete Pareto curve, which involves the optional representation of possible compromise solutions. Here, two pairs of different objectives are considered as distinguished strategies. Optimisation of the first strategy predicts a maximum power output of 108.33 kW at a breakeven per-unit energy cost of 0.51 $/kWh and minimum breakeven per-unit energy cost of 0.30 $/kWh at a power of 42.18 kW. In the second strategy, maximum efficiency of 63.93%at a breakeven per-unit energy cost of 0.42... 

In this article, a feed-forward neural network is explored to reconstruct the performance map of an axial compressor through the utilization of a limited number of experimental data. The Levenberg-Marquardt algorithm with Bayesian regularization method is used to adjust the weights and biases of the network. The proposed technique is utilized to estimate the mass flowrate, the pressure ratio, the shaft speed, and the efficiency in regions where no experimental data are available. The surge line is predicted and the line of maximum efficiencies is determined. The results are compared with experimental data  

In optimum designing of wireless power transfer(WPT) coils, maximum efficiency and maximum power transfer capability of coils should be considered. In this paper, a novel technique for optimum design of WPT coils based on maximum efficiency with considering required power transfer capability has been given. Optimum selection of system parameters including coil and wire dimensions, number of turns of coils and compensation capacitor selection based on minimum weight of copper mass is also given. For evaluation purpose a 100W experimental sample is designed and tested in 20cm range  

In this paper, a new zero-voltage-switching, high power-factor, bridgeless rectifier is introduced. In this topology, an auxiliary circuit provides soft switching for all of the power semiconductor devices. Thus the switching losses are reduced and the highest efficiency can be achieved. The proposed converter has been analyzed and a design procedure has been introduced. The control circuit for the converter has also been developed. Based on the given approach, a 250 W, 400 Vdc prototype converters has been designed at 100 kHz for universal input voltage (90-264 Vrms) applications. A maximum efficiency of 94.6% and a power factor correction over 0.99 has been achieved. The simulation and... 

In this paper, a new zero-voltage-switching high power-factor (PF) rectifier with Line-Modulated Fixed-Off-Time current control is introduced, that off time is a function of the instantaneous line voltage. The auxiliary circuit provides soft switching for all semiconductor devices, without any extra current and voltage stress on the main switches. The proposed converter is bridgeless, and all semiconductor devices are soft switched. In addition, there is no extra stress on the switches. Thus, the conduction and switching losses are reduced and maximum efficiency is achieved. A 250W, with an input ac voltage of 90265 Vrms and an output voltage 400 Vdc, 100 kHz is designed and simulated to... 

LLC resonant converter has been used widely as dc-dc converter for achieving constant dc voltage. In this paper, an LLC resonant converter, by adding an inductance to its conventional topology and considering the rectifying stage stray inductances, is proposed for an adjustable wide range regulated current source (20-200 A dc) for using as ion implanter's filament power supply. The additional inductor increases output current adjustment range and efficiency, especially at light loads. Transformer's leakage inductances and rectifying stage stray inductances have been considered. Because of these inductances, the rectifier stage always works in continuous conduction mode, and its conduction... 

LLC-LC resonant converter is a suitable circuit topology to design switched-mode power supplies for wide-output-voltage and wide-output-load applications. In this paper, a design procedure is introduced to optimize this converter. Unlike soft switching techniques for pulse width modulated converters, which usually apply an active auxiliary circuit to reduce switching losses and EMI, in the proposed converter, not only such circuits are not used, but also all of the parasitic elements are merged to the converters main components. Zero-voltage switching (ZVS) operation is realized for all power devices under all operating conditions. Thus, this converter is a suitable choice for...