Sharif Digital Repository

Cryptographic algorithms utilize finite-field arithmetic operations in their computations. Due to the constraints of the nodes which benefit from the security and privacy advantages of these algorithms in sensitive applications, these algorithms need to be lightweight. One of the well-known bases used in sensitive computations is dual basis (DB). In this brief, we present low-complexity superserial architectures for the DB multiplication over GF (2m). To the best of our knowledge, this is the first time that such a multiplier is proposed in the open literature. We have performed complexity analysis for the proposed lightweight architectures, and the results show that the hardware complexity... 

In order to access to an accurate detection of electrocardiogram signal in medical approaches especially mobile health and wearable medical devices, development of noise cancellation algorithms seems essential. In this study, the power line noise in ECG signal is filtered using several methods including DFT based, IIR, FIR, adaptive, Kalman, Wavelet and higher order statistics filters. Signal-to-noise ratio (SNR) improvements of the filters are then compared. It is found that FIR and IIR filtering show higher SNR improvement  

Medical applications of rapid prototyping have an increasing trend, making the future of RP more and more promising. These applications may include design, development, and manufacture of medical devices and instrumentation, as well as implant design, anatomical modeling, surgical planning, surgical implants, and prosthesis fabrication. This paper provides a new methodology for customized hip prosthesis that could provide high accuracy of femoral canal reconstruction via 3D modeling of prosthesis stem, 3D modeling of prosthesis neck, and facilitating the communication between the designer and surgeon. Combining RP technologies and rapid tooling with this novel custom-made hip prosthesis,... 

A precise and compact tubular ultrasonic motor driven by a single-phase source is proposed and tested in this study. The motor is designed by modeling a motor stator in FEM software. The motor fabricated according to the design is tested experimentally and its working characteristics including speed and torque are measured and presented. The maximum speed and torque of the motor are 59 rpm and 0.28 mN m at 80 Vpp of applied voltage. The proposed motor possesses advantages such as a simple and compact structure with application in the fields of robotics, space, medical devices and high-resolution stages, among others. The proposed motor is a good candidate for applications where accurate... 

A new wearable assistive device (WAD) was developed to decrease required force on the lumbar spine in static holding tasks. In order to obtain moments on lumbar spine in two conditions, with and without WAD, a biomechanical static model was used for estimation of external moments on lumbar spine. The results of biomechanical models indicated that there was a reduction in the lumbar moment ranging from 20% to 43% using WAD depending on the load and flexion angle. A total of 15 male healthy subjects were tested to experimentally verify the predicted reduction of external moments on the spine by wearing WAD. Normalized electromyography (EMG) of the right and left lumbar and thoracic erector... 

Background Motor control exercise was claimed to improve spinal stability in patients with chronic non-specific back pain, but to investigate the effectiveness of this exercise, other outcome measures have been used rather than spinal stability itself. The aim of our study is to assess motor control exercise effects on spinal stability using a biomechanical model. Methods Fifty-one patients were assigned to either motor control or general exercises. Before and after trainings, participants were tested for spinal stability at seven isometric tasks. Electromyography signals were recorded from ten superficial muscles, and a hybrid EMG-driven musculoskeletal model estimated spinal stability... 

In modern wireless near-filed power and data telemetry systems such as Implantable Medical Devices (IMD), a data rate of several Mbps is required, while the power carrier frequency is limited to few MHz. Therefore, bit rate is comparable to carrier frequency, and the modulated power carrier signal has amplitude, frequency, or phase variation in every cycle. In this paper a very fast amplitude shift keying (ASK) demodulator circuit is presented. The proposed demodulator is able to demodulate a cycle by cycle ASK modulated signal, and a data-rate-to-carrier (DRC) ratio of 100% is achievable. The circuit extracts the clock by limiting the incoming ASK signal. Cycle by cycle demodulation is done... 

Due to the importance of hydrogen as an effective antioxidant for its applications in therapy, this research reports the fabrication of a coupled microfluidic microbial electrochemical cell (MXC), including microfluidic microbial fuel cells (MFCs) and a microfluidic microbial electrolysis cell (MEC) series in order to perform it as a self-powered biohydrogen generator. Being able to be a platform of implantable medical devices, utilization a non-phatogenic strain of Escherichia coli as the biocatalyst in order to exploit the embodied energy from human blood and excrement and finally the use of cheap and facile materials (<$2 per device) are the exceptional features of the system. The... 

This study reports the fabrication of a microfluidic microbial fuel cell (MFC) using nickel as a novel alternative for conventional electrodes and a non-phatogenic strain of Escherichia coli as the biocatalyst. The feasibility of a microfluidic MFC as an efficient power generator for production of bioelectricity from glucose and urea as organic substrates in human blood and urine for implantable medical devices (IMDs) was investigated. A maximum open circuit potential of 459mV was achieved for the batch-fed microfluidic MFC. During continuous mode operation, a maximum power density of 104Wm-3 was obtained with nutrient broth. For the glucose-fed microfluidic MFC, the maximum power density of... 

Range of motion (ROM) of the thoracic spine has implications in patient discrimination for diagnostic purposes and in biomechanical models for predictions of spinal loads. Few previous studies have reported quite different thoracic ROMs. Total (T1-T12), lower (T5-T12) and upper (T1-T5) thoracic, lumbar (T12-S1), pelvis, and entire trunk (T1) ROMs were measured using an inertial tracking device as asymptomatic subjects flexed forward from their neutral upright position to full forward flexion. Correlations between body height and the ROMs were conducted. An effect of measurement errors of the trunk flexion (T1) on the model-predicted spinal loads was investigated. Mean of peak voluntary total...