Sharif Digital Repository

In this paper, a wideband coupled-resonator microstrip bandpass filter is designed and experimentally demonstrated in the S-Band. The filter is comprised of quarter-wavelength hair-pin resonators, reducing resonator and filter footprint compared to conventional hairpin designs. Additionally, it is considerably forgiving to fabrication tolerances and yields remarkably close matched results between theory, simulation, and measured results. One demonstration presented has minimal insertion loss ${(< 1{dB})}$ for the entire wide bandwidth of 3.4 GHz to 4.2 GHz. Wider bandwidths up to 60% are also observed using the design. The proposed filter is an attractive solution when space is a critical... 

Quarter-wavelength superconducting spiral resonators have been used to realize a coplanar waveguide bandpass filter and bandstop filter around the center frequency of 6 GHz. These compact coplanar waveguide filters have been made from 300-nm-thick NbTiN thin film on a 525-μm-thick silicon substrate. The bandpass filter is a six-pole Chebyshev filter with two zero transmissions due to nonadjacent coupling in its structure. Accurately microfabricated air-bridges have been used to suppress the undesired slot-line mode in this filter. The bandstop filter is a very simple two-pole structure that used wire bonding to suppress the slot-line mode. Measurements have been done at a temperature of 4.2... 

A tunable IIR microwave-photonic filter (MPF) with controllable selectivity is implemented using an electrically tunable delay line. The proposed method has been experimentally tested and verified. An IIR Microwave-Photonic filter with variable Q factor in the range of 238 - 257 is realized  

We have developed an analytic approach to investigate the effect of group delay ripple on the performance of phase-modulated microwave photonic filter. Two cases with and without ripple are analyzed to clarify the ripple's effects on the performance of microwave-photonic filter. Comparison of our proposed analytical approach with simulated OptiSystem® results shows a good agreement  

In this paper, we present a design method of dual-band waveguide rectangular cavity filters, with a series in-line topology. The coupling matrix is based on asynchronously tuned designs, where two sets of resonances exist for the two bands. Thus the filter is inherently different than the typical dual-band designs in the literature, as existing designs utilize resonators at the same frequency. The design at Ku band validates the underlying idea and concept, and the theory of the detuned coupling matrix. This rectangular waveguide implementation can provide noticeable miniaturization in applications with high-power requirements  

In this article, a dual-band sixth order double symmetric T-slot filter is proposed for the 5G communication systems. This filter contains two duplicate square resonators and a T-shape feedline on the Rogers RT duroid 5880 substrate. Operating at the 28 and 38.5 GHz frequencies from licensed 5G frequency bands and small size make this filter appropriate for different 5G applications. Furthermore, an LC equivalent circuit for the filter has been considered that helps us to have a better sight of this filter. Measurement results show good agreement with simulations. The attenuation on the passband is less than 1 dB. In order to evaluate the filter performance besides other millimeter waves... 

Superconducting materials are known to exhibit nonlinear effects and to produce harmonic generation and intermodulation distortion in superconductive circuits. In planar structures, these nonlinearities depend on the current distribution on the strip which is mainly determined by the structure of the device. This paper investigates the current distribution at the step-in-width discontinuity in superconducting microstrip transmission lines, which is computed by a numerical approach based on a 3-D finite-element method. This current distribution is used to obtain the parameters of the nonlinear circuit model for the superconducting microstrip step-in-width discontinuity. The proposed... 

We have developed an analytic approach to investigate the effect of group delay ripple of the dispersive devices on the performance of two major building blocks of microwave- photonic filters. Firstly, performance of PM-based block in the presence of an arbitrary group delay ripple (GDR) is analyzed and compared with the ripple-free case to reveal the destructive effects of added group delay ripple. In the next step, we repeat the proposed approach for the AM-based one; again, the performance is compared with the ripple-free case. Two distortion metrics are also introduced to quantify this distortion. Comparison of the performance of two building blocks in the presence of group delay ripple... 

Microwave filters have successfully been miniaturized using spiral resonators. One of the typical problems in wideband microwave filters, such as spiral filters, is the need for very small gaps between resonators to accomplish high external and internal coupling. These gaps cause difficulties in the physical implementation of the filter, especially at high frequencies. To avoid this problem and to enable easy fabrication of the filter, a rectangular microstrip patch was used as a coupling capacitor instead of small gaps between resonators. This technique was used both for external and for internal coupling of the filter. Additionally, this approach has another important benefit; it removes... 

Novel types of narrow band filters based on the newly introduced gap waveguide technology are presented in this paper. The proposed filters have a central frequency of 35 GHz with approximately 1% fractional bandwidth. The filter resonators are composed of two separate plates and are manufactured by milling metallic blocks. The gap between the two metallic plates eliminates the need for electrical contact between them. This feature allows the resonators to be stacked in different layers. The filtering function is realized by producing a coupling between the stacked resonators. The measurement results of the manufactured filters are in good agreement with full-wave simulations, even without... 

We have developed an analytic approach to investigate the effect of a sinusoid group delay ripple on the performance of phase-modulated microwave photonic filter. Frequency of fabricated sinusoid ripple determines the pole's frequency of the resulted transfer function. Comparison of our proposed analytical approach with simulated OptiSystem results shows a good agreement