Sharif Digital Repository

An astigmatism compensated isosceles triangular ring resonator is designed and tested for a subjoule class Nd:YAG laser, considering the thermal lensing effects. The ABCD approach is used and the laser rod is considered as a lens like media whose optical power is induced by dissipated heat in the rod. The beam spot size, divergence angle, and some other parameters were studied for both sagittal and tangential planes and a minimal astigmatic configuration is designed applying dynamic stability condition. It is shown practically that the designed resonator emits a circular TEM00 Gaussian beam (using an aperture). Comparative studies were also done considering a linear resonator especially for... 

Conversion of CH4 molecule into higher hydrocarbons using two different wavelengths of 248 nm KrF laser and 355 nm of third harmonic of Nd:YAG laser is studied experimentally and theoretically. The stable products are analyzed and the effect of pressure on conversion of methane is measured. The detected reaction products are C2H2, C2H4, and C2H6. The conversion efficiency of 33.5% for 355 nm in comparison to 2.2% conversion for 248 nm for C2H2 is achieved. The potential of laser parameters as an important variable in controlling of final products is investigated  

12 mJ, 10-Hz green pulses from frequency doubled Nd:YAG laser was used for pumping Rhodamine 6G in a dye laser based on multiple-prism beam expander. In order to increase the stability of the output pulse, a unique dye cell with variable dimensions of active medium was designed and constructed. By using multiple-prism dispersion theory, conditions for zero-dispersion in two and four-prism beam expander configuration was calculated. In the case of two-prism configuration, tuning range of dye laser was 565–595 nm and the linewidth of pulse at 580 nm was about 1.8 nm and it is in good agreement with the calculated amount of 1.6 nm. Furthermore, using four-prism configuration tuning range of... 

Laser ablation of titanium target in distilled water for synthesis of colloidal nanoparticles is studied both experimentally and theoretically. The effects of laser parameters such as wavelength, pulse energy, fluence and shot numbers on the ablation rate and size properties of colloidal nanoparticles are investigated. The experimental approach addresses the interesting issue for finding the optimal main experimental parameters of laser ablation. The theoretical thermal model of nanosecond pulsed laser ablation is developed to visualize the evolution of temperature distributions and ablation depth. The simulation result of ablation depth has been compared with the experimental result... 

The propagation of a Gaussian beam in underdense plasma with upward increasing density ramp is analyzed. In this work are shown that the spot size oscillations of laser beam increases and its amplitude shrinks with proper plasma density ramp. This causes the laser beam to become more focused and penetrations deep into the plasma by reduction of diffraction effect. The related focusing parameters are optimized to get the best possible focusing at the relativistic threshold intensity of Nd-glass laser and the effect of the laser intensity in the self-focusing parameters is also investigated. The analytical calculations are presented and showed more reliable results in comparison to the... 

Tunability of the Fermi level of graphene is exploited to implement a plasmonic nano-color-sorter for scanning near-field optical microscope (SNOM) applications capable of handling large tip sample couplings. Nano-color-sorting has been used in SNOM through creating multiple spatially separated hot spots for different incident wavelengths. We show that in the presence of high-refractive-index samples an unwanted redshift in the spectral response of the dual-color probe occurs. This limitation can be compensated for using graphene and adjusting its chemical potential to obtain a blueshift in probe spectral response. The Method of Moments analysis technique is employed to engineer the probe... 

A wide variety of carbon nanostructures were generated by a Q-switched Nd : YAG laser (1064 nm) while mostly nanodiamonds were created by an ArF excimer laser (193 nm) in deionized water. They were characterized by transmission electron microscopy, Raman spectroscopy and x-ray photoelectron spectroscopy. It was found that the IR laser affected the morphology and structure of the nanostructures due to the higher inverse bremsstrahlung absorption rate within the plasma plume with respect to the UV laser. Moreover, laser-induced breakdown spectroscopy was carried out so that the plasma created by the IR laser was more energetic than that generated by the UV laser  

Tungsten oxide nanoparticles were fabricated by a pulsed laser ablation method in deionized water using the first harmonic of a Nd:YAG laser (λ = 1064 nm) at three different laser pulse energies (E1 = 160, E2 = 370 and E3 = 500 mJ/pulse), respectively. The aim is to investigate the effect of laser pulse energy on the size distribution and gasochromic property of colloidal nanoparticles. The products were characterized by dynamic light scattering (DLS), atomic force microscopy (AFM), X-ray photoelectron spectroscopy (XPS) and UV-Vis spectroscopy. The results indicated that WO 3 nanoparticles were formed. After ablation, a 0.2 g/l PdCl 2 solution was added to activate the solution against... 

The present paper reports the effects of Nd:YAG laser welding on the microstructure, phase transformation, cyclic deformation behavior, and corrosion resistance of Ti-55 wt.% Ni wire. The results showed that the laser welding altered the microstructure of the weld metal which mainly composed of columnar dendrites grown epitaxially from the fusion line. DSC results indicated that the onset of the transformation temperatures of the weld metal differed from that of the base metal. Cyclic stress-strain behavior of laser-welded NiTi wire was comparable to the as-received material; while a little reduction in the pseudo-elastic property was noted. The weld metal exhibited higher corrosion... 

In this study, colloidal tungsten oxide nanoparticles were fabricated by pulsed laser ablation of tungsten target using the first harmonic of a Nd:YAG laser (1064 nm) in deionized water. After ablation, a 0.33 g/lit HAuCl4 aqueous solution was added into as-prepared colloidal nanoparticles. In this process, Au3+ ions were reduced to decorate gold metallic state (Au0) onto colloidal tungsten oxide nanoparticles surface. The morphology and chemical composition of the synthesized nanoparticles were studied by AFM, XRD, TEM and XPS techniques. UV-Vis analysis reveals a distinct absorption peak at ∼530 nm. This peak can be attributed to the surface plasmon resonance (SPR) of Au and confirms... 

The welding behavior of the Fe-Co-7 wt% V ultra-thin foils was examined using the Nd:YAG laser welding method. Scanning electron microscopy and electron backscattered diffraction were used to investigate microstructural changes and fracture mechanism of the weld joints. Tensile test and microhardness measurement were employed in order to study the mechanical behaviors of the welds. Microstructural observations indicated that a bimodal grain size distribution is seen in the fusion zone. It was found that the fracture surfaces of the welds consist of both cleavage sites and dimples. It was also revealed that the cleavage sites are mainly located in the coarse grain zone while numerous dimples... 

This research aims to investigate the effect of pulsed Nd:YAG laser micro-welding on the microstructure, texture and magnetic properties of ultra-thin Fe-Co-7.15 wt% V magnetic alloy. Optical microscopy, scanning electron microscopy and electron backscattered diffraction techniques were used to study the microstructural evolutions. Also, vibrating sample magnetometry was used to characterize the magnetic properties. The results showed that the fractions of low Σ coincidence site lattice boundaries in the fusion zone are higher than those of the base metal. The welded samples experience a significant decrease in their magnetic properties. It was found that the formation of new fiber texture... 

Here we report on the production of highly directed ion blocks by plasma interaction of ultraviolet wavelength light produced from a KrF laser. This may support the requirement to produce a fast ignition deuterium-tritium fusion at densities not much higher than the solid state by a single shot petawatt-picoseconds ultraviolet laser pulse. Using double Rayleigh initial density profiles, we are studying numerically how the nonlinear force necessary to accelerate plasma blocks may reach the highest possible thickness. Propagation of plasma blocks and the volumetric hot electrons can be shown in detail. Results of computations for wavelengths of two lasers are compared, which show that the... 

Machining of ceramics often involves many challenges due to their high hardness, brittleness, and low thermal properties. Laser assisted machining (LAM) is a promising technology for improving the machinability of hard-to-cut materials. In this work, laser assisted machining of slip cast fused silica (SCFS) ceramics is investigated by presenting a numerical thermal analysis of laser effects on material behaviour. A transient three-dimensional heat transfer analysis for laser assisted turning of SCFS is performed using finite element method. Temperature distributions in SCFS cylindrical specimens are obtained. Experimental results are provided to validate the numerical results  

Laser cutting characteristics including power level and cutting gas pressure are investigated in order to obtain an optimum kerf width. The kerf width is investigated for a laser power range of 50-170 W and a gas pressure of 1-6 bar for steel and mild steel materials. Variation of sample thickness, material type, gas pressure and laser power on the average cut width and slot quality are investigated. Optimum conditions for the steel and mild steel materials with a thickness range of 1-2 mm are obtained. The optimum condition for the steel cutting results in a minimum average kerf width of 0.2 mm at a laser power of 67 W, cutting rate of 7.1 mm/s and an oxygen pressure of 4 bar. A similar... 

A pulsed Nd:YAG laser welding of 1 mm thick Ti (grade 2) to 0.5 mm thick AA3105-O was performed by a ring-like spot joining. A 0.15 mm thick Al-12Si-2.5 Mg alloy was used as a filler metal. Intermetallic compounds of Ti3Al, Ti2Al, TiAl, Ti(Al,Si)3 and Mg2Si were observed respectively from Ti towards Al sides at the fusion zone. Si and Mg increased the strength of the Al re-solidified zone near the Ti-Al interface because of their easy dissolution in the Al. Exothermic effect of the Mg addition resulted in porosity in the welding zone. Joint strength of up to 98% of the Al base metal was obtained, which was much 14% higher than that achieved by autogenous welding. © 2019 Elsevier GmbH  

This paper presents the study of the structural and optical properties of copper doped cadmium sulfide thin films prepared by pulsed Nd:YAG laser. The copper concentration in the targets was varied from 0.05% to 5% in weight and they were heated at a temperature of 500°C in air for one hour. It was observed that annealing un-doped and doped thin films at temperatures above 160°C leads to an abrupt increase in the optical transmission, changing from dark brownish to transparent yellowish. For annealed samples at 300°C, increasing Cu concentration from 0.0% to 2%, leads to an increase in the optical transmission up to 80%, at a wavelength of about 700 nm. XRD patterns showed the hexagonal... 

Creating laser texture on dental implants is a novel method for accelerating osseointegration and prolongation of lifespan. The purpose of this research was twofold: (1) Creating intersecting lines pattern with different angles (0°, 15°, 30°, 45°, 60°, 75°, and 90°) on the surface of Ti6Al4V, using pulse Nd:YAG laser with a wavelength of 1064 nm and a pulse length of 170 ns and (2) comparing optical and SEM images, EDS analyses, contact angles (CAs), and surface free energies (FEs) for different intersecting lines angles. CA and FE depended on the intersecting lines angle according to Y = Y 0 + A sin (x B + C), where Y is the CA or FE; x is the intersecting lines angle; and Y0, A, B, and C... 

Laser drilling is a well-established manufacturing process utilised to produce holes in various aeroengine components. This research presents an experimental investigation on the effects of laser drilling process parameters on productivity (material removal rate), hole quality (hole taper) and drilling cost. Single-pulse drilling was employed to drill a thin-walled Inconel 718 superalloy plate of 1 mm thickness using pulsed Nd:YAG laser. The experiments were designed using Box-Behnken statistical approach to investigate the impacts of pulse energy, pulse duration, gas pressure and gas flow rate on the selected responses. Multi-objective optimisation was performed using response surface... 

In this study, a pulsed Nd:YAG laser welding method is implemented to join Ti-G2 (1 mm thick) to AA3105-O (0.5 mm thick) via a ring of spots filled with AlScZr alloy (0.15 mm thick). The filler material improved the weld’s microstructure and mechanical properties by reducing the undesirable intermetallic compounds (IMCs) such as TiAl2 and TiAl3 in the aluminium re-solidified zone near the titanium/aluminium interface. The joints having AlScZr filler were mostly failed at Al heat affected zone (HAZ) during the tensile shear test. The addition of zirconium to binary Al–Sc system formed a substitutional solid-solution in which 50 wt% Zr+10 wt% Ti replaced Al3(Sc,Zr,Ti). Scandium had a...