Sharif Digital Repository

The key feature of diffusion brazing, also referred to as transient liquid phase bonding, is isothermal solidification which precludes the formation of intermetallic in the joint centreline. Analysing the available data published in the literature showed that the composition of the nickel-based superalloys plays a strong role in determining the required time for obtaining intermetallic-free joint during diffusion brazing. This effect is not predictable by the standard conventional models. It is proposed that increasing the boride-forming elements in the base superalloy which promotes in situ boride precipitation at the diffusion-affected zone can accelerate the diffusion flux of the boron... 

Fundamental understanding of the intermetallic phase formation is the key for enhancing the robustness and reliability of the brazed joints. The paper addresses the phase transformations during brazing of the Hastelloy X nickel-base superalloy using the quinary Ni–13Cr–4.5Si–4.2Fe–2.8B (wt-%) braze alloy. The mechanisms of intermetallic formation via solidification and solid-state precipitation are discussed. The athermal solidification zone (ASZ) is featured by the formation of brittle and hard borides and boro-silicides that are formed via eutectic reactions. However, in contrast to other commercial B-bearing Ni-based filler alloys, it was identified that the presence of a high-volume... 

In transient liquid phase (TLP) bonding for commercial applications, one of the important key parameters is the holding time required for complete isothermal solidification tIS, which is a prerequisite for obtaining a proper bond microstructure. The objective of the study is to analyse the isothermal solidification kinetics during TLP bonding of cast IN718 nickel based superalloy. Experiments for TLP bonding were carried out using a Ni-7Cr-4.5Si-3Fe-3.2B (wt-%) amorphous interlayer at several bonding temperatures (1273-1373 K). The time required to obtain TLP joints free from centreline eutectic microconstituents was experimentally determined. Considering the solidification behaviour of... 

The production of robust joints after diffusion brazing necessitates the advanced understanding of phase transformations during the bonding process. This paper aims to investigate the solidification and the solid state precipitation during diffusion brazing of wrought IN718 nickel base superalloy using Ni-15Cr-4B (wt-%) filler alloy. It was found that intermetallics containing eutectic type microconstituents were formed in the joint centreline by solidification which is controlled by segregation behaviour of B and its low solubility in Ni rich solid solution. In addition, extensive Cr-Mo-Nb rich precipitates were formed in the substrate region by solid state precipitation induced by B... 

This paper aims at addressing the microstructure-strength characteristics relationship during transient liquid phase (TLP) bonding of cast IN718 nickel based superalloy using Ni-7. Cr-4.5. Si-3. Fe-3.2. B (wt%) amorphous interlayer. The progress of the isothermal solidification at different temperatures for different times is analyzed using a Larson-Miller parameter (LMP). It was found that there is direct relationship between isothermal solidification zone (ISZ) size and LMP. Results showed that in situation where isothermal solidification has not been completed, the ratio of athermal solidification zone (ASZ) size to the width of the total solidified zone is the controlling factor for... 

Friction stir processing (FSP) of high softening-temperature materials such as nickel-based superalloys is considered to be difficult. Laser heating of a localised area ahead of the FSP tool was used to provide sufficient plasticity during the FSP of IN738LC nickel-based superalloy. The stir zone (SZ) microstructure of the friction stir processed and laser-assisted friction stir processed were characterised. Laser-assisted friction stir processing (LAFSP) produced a defect-free pass, but FSP resulted in generation of a discontinuity in the SZ. Both lower volume fraction of partially dissolved γ′ precipitates and coarser grain structure of SZ in LAFSP led to more ductility of the SZ material... 

This work presents the effect of co-sintering on the densification and microstructural evolution in the two-layer stepwise graded composite of INCONEL 718 and INCONEL 625 superalloys. A pressureless co-sintering method in conjunction with a powder layering technique was used. The sintering was carried out in solid state and liquid phase in temperature ranging from 1260 °C through 1300 °C for 60 minutes in a low pressure of an argon atmosphere. Nonisothermal sintering behavior was also examined by dilatometric analysis. Similarly, the sintering response of the individual layers was characterized. The results reveal an enhanced densification rate during co-sintering of the composite layers.... 

Rene-80, as an alloy for production of the jet turbine blades, shows high mechanical properties as well as microstructure stability during the high temperature engine operation. In this study we tried to have a deep insight on the microstructure of the cast Rene-80 and the evolution of microstructure during the different stages of the relatively complex GE class-A heat treatment. Although the solution heat treatment homogenized the chemical alloy segregation resulted from the casting to some extent, it did not cause all the casting γ′ particles to dissolve completely in the matrix. Primary aging caused growth in the residue particles as well as growth of the new precipitated particles, which... 

The paper aims at understanding solidification phenomena and solid state precipitations during diffusion brazing of Hastelloy X nickel base superalloy using a ternary Ni–4.5Si–3.2 B (in wt-%) filler metal. The joint is featured by the formation of Ni-rich solid solution in an isothermal solidification zone, borides/silicide formation during eutectic-type solidification in an athermal solidification zone, on-cooling precipitation of fine nickel silicides in the joint centerline, in situ precipitation of Mo–Cr-rich borides in the diffusion affected zone and grain growth in the heat affected zone. The implication of the phase transformations on the joint properties is discussed. It is shown... 

The microstructure of dissimilar transient liquid phase bond between Hastelloy X and IN792 nickel-based superalloys is featured by lack of sufficient formation of γ′ precipitates in the bond-centerline and extensive in-situ precipitation of boride second phases in the diffusion affected zones (DAZ). This paper investigates the impact of two thermal processing strategies, using standard solution treatment and aging of IN792 (STA strategy) and using solution treatment of IN792 followed by a post-bond heat treatment utilizing solution treatment of Hastelloy X and aging treatment of IN792 (SPTA strategy) on the joint microstructure and mechanical properties. The boride precipitates in the DAZ of...