Sharif Digital Repository

In the present study, a one step hydrothermal process was employed to synthesize magnetite nanoparticles using oleic acid as surfactant agent at 140 °C. Effects of reaction time and alkalinity were studied on particles size and morphology. By changing these parameters, some monodisperse spherical nanoparticles with mean particle size between 2.71 and 13.88 nm were synthesized and characterized via TEM, XRD, VSM, TGA and FT-IR techniques. Assuming the Avrami behavior of particles formation, a kinetics equation was proposed for the transformation rate at 140 °C. Using some simplifying assumptions, nucleation and growth rates were calculated for the hydrothermal formation of magnetite... 

A 3D continuum code coupled with a kinetic Monte Carlo module has been developed for the simulation of Ni electrocrystallization in the initial stages of nucleation and growth. Mass transfer in solution was controlled by a finite-difference code which is distributed over an irregular nanoscale grid system in vertical direction to the substrate. Deposition events such as surface diffusion, chemisorption and crystallization in the system were considered in a KMC module that processes the output of a diffusion-controlled scheme in probability functions to model electrodeposition process on surface. Electrochemical data of this simulation was simultaneously generated according to analytical... 

Carbon dioxide sequestration by a pH-swing carbonation process was considered in this work. A multi-step aqueous process is described for the fractional precipitation of magnesium carbonate and other minerals in an aqueous system at room temperature and atmospheric pressure. With the aim to achieve higher purity and deliver more valuable mineral products, the process was split into four steps. The first step consists of Mg leaching from the magnesium silicate in a stirred vessel using 1 M HCl at 80 °C, followed by a three step precipitation in reactors in sequence to remove Fe(OH)3, then Fe(OH)2 and other divalent ions, and finally MgCO3 nucleation and growth. Hydrated magnesium carbonate... 

A novel nanocomposite of ZnO-PbO with flower-like nanostructure was fabricated from zinc acetate and lead nitrate as principle raw materials via an in situ process. The novelty of this study consists in the use of a common approach for fabricating of ZnO and PbO nanoparticles simultaneously. From these experiments the conclusion might be drawn that Zn(NH4) 2 4+ ions and Pb(OH)2 act as precursors for the nucleation and growth of ZnO and PbO respectively under microwave irradiation. The precursors formation were carried at two stages: reaction between zinc ions and lead nitrate with ammonium ion and hydroxide sodium respectively. The average crystalline size of Zno and PbO has been analysed by... 

Nucleation and growth of condensing droplets on horizontal surfaces are investigated via a 2-D double distribution function thermal lattice Boltzmann method. First, condensation on completely uniform surface is investigated and different mechanisms which cause dropwise and filmwise condensation are studied. The results reveal the presence of cooled vapor layer instability in the condensation on completely smooth surfaces. In the second step, condensation on chemically heterogeneous surfaces is investigated. Moreover, the effect of non-uniformity in the surface temperature is also studied. The results indicate that the vapor layer instability and the nucleation start from the heterogeneities.... 

Monodispersed semiconducting nanoparticles are usually synthesised in a liquid medium using injection of an appropriate solution. A key factor in attaining a narrow particle size distribution (PSD) is the temporal separation of the nucleation and growth stages, where the former takes place during the injection. Faster injection produces a larger number of nuclei and a narrower PSD. The injection speed is expected to affect the diffusion of the ions in the solution and to create uniformly high supersaturation for a short period of time. In this paper, we study the growth of CdS nanoparticles during the injection by molecular dynamics simulation. A solution of Cd ions is injected into the... 

Static recrystallization and microstructural changes in austenitic stainless steel 304L were studied. The rolling experiments at 200 °C were carried out, and then, annealing treatment was made at temperatures ranging between 500 and 830 °C. A model was also developed to simulate the kinetics of non-isothermal recrystallization within the rolled steel. The distribution of plastic strains during rolling was predicted utilizing an elastic–plastic finite element formulation performed in ABAQUS/Explicit, while the predicted results were used to generate the as-rolled microstructure and to estimate the stored energy. Finally, microstructural–thermal model based on cellular automata was developed... 

The early stages of nucleation and growth of nanostructures can control the shape and final size of the fabricated nanostructure. Therefore, the study of the nucleation and growth mechanism of nanostructures is of great importance. The purpose of this study is to investigate the nucleation and growth mechanism of nickel nanocones from a chloride-based bath containing ethylene ammonium dichloride as a crystal modifier. Cyclic voltammetry (CV), electrochemical impedance spectroscopy (EIS) and chronoamperometry tests were employed to investigate the nucleation and growth mechanism and also the mechanism of crystal modifier performance on the growth of nanocones. Electrochemical studies revealed... 

Single-walled carbon nanotubes (SWCNTs) and multiwalled carbon nanotubes (MWCNTs) were synthesized in aqueous solutions containing FeCl2, FeCl3, FeSO4 and Fe2(SO4) 3. The effects of iron charge and the counter ions on the formation of carbon nanotubes (CNTs) were investigated. Thermogravimetric (TG) analysis indicated that carbon multilayer structures including CNTs and multishell graphite particles were formed in deionized (DI) water without the iron precursor. SWCNTs were also synthesized in the presence of the iron ions. It was also found that the mole ratio of [Fe2+]/[Fe3+] in the solution has a significant influence on the purity of CNTs and the process yield. The highest yield was... 

Abstract In this study, aluminium titanate (AT) particles and nanofibers were synthesized through citrate sol gel and sol gel-assisted electrospinning methods in both nanostructured powder and nanofiber forms. The results of X-ray diffraction analysis, field-emission scanning electron microscopy and differential thermal analysis showed that the synthetic products benefit a nanostructured nature with a grain size less than 70 nm. The optimal values for time and temperature at which a roughly pure AT is attained were determined as 2 h and 900 C, respectively. It was found that the sol gel precursor bears an amorphous structure till 700 C and begins to be crystallized to alumina, anatase and AT... 

Titanium dioxide nanopowders were synthesized by the diffusion controlled sol-gel process (LaMer model) and characterized by DTA-TG, XRD, and SEM. The prepared TiO 2 nanoparticles have uniform size and morphology, and the phase transformation kinetics of obtained material was studied by interpretation of the X-ray diffraction patterns peaks on the base of Avrami equation. The stating point of anatase-rutile phase transformation temperature in the prepared nanoparticles was found between 100 and 200 C. A decreasing trend on the intensity of X-ray peaks of anatase phase was observed up to 600 C when the presence of the rutile phase became predominant. Results indicated that the transition... 

Ultra fine CuO nanoparticles In the range of 2 ± 0.2 nm were synthesized by the supercritical hiydrotliermal method in a batch reactor. Itwas demonstrated that elevating the pH of the Cu2+ precursor solution to around 6 (neutral condition) not only does not lead to excessive agglomeration of the particles, but also reduces particle size and in general promotes their nanoscale characteristics. Prepared nanoparticles were immobilized in the biopolymcric matrix of barium alginate and calcined at different temperatures resulting in micro spherical granules of high porosity and elevated mechanical strength. The fabricated samples were characterized using x-ray diffractometry (XRD), transmission... 

One-dimensional (1D) MgO structures were successfully synthesized via carbothermic reduction of mechanically activated mixture of MgO and graphite. Mechanical activation of source materials before carbothermic reduction can substantially enhance the formation of MgO products at a temperature (1000 °C) relatively lower than that required in previous approaches (≥1200 °C). However, the morphology of MgO formed is dependent on the degree of mechanical activation and the condition of the subsequent carbothermic reduction. Two distinctive morphologies were found for MgO products synthesized using our method: single crystalline nanorods with rectangular cross-sections whose diameters range from 50... 

Co/Cu multilayers were deposited in a sulfate solution by controlling the current and potential for the deposition of cobalt and copper layer respectively. The electrochemical behavior of these multilayers was studied by cyclic voltammetry and current transients. In addition, a mathematical analysis was used to characterize the electrodeposition system. Simultaneously, the nucleation and growth mechanisms were monitored by these techniques. In this case, the results clearly showed that electrodeposition of cobalt layers was a kinetically controlled process while the reduction of copper ions was a diffusion-control process. Although nucleation mechanism of the single Co deposit was found as a... 

Electrodeposition of gold nanowires is carried out in cyanide solution in polycarbonate templates with pore diameter of 80 nm. Electrochemical methods are utilized to characterize the gold electrodeposition and to obtain the nucleation and growth mechanism. The analysis of cyclic voltammograms shows that the electrodeposition of gold nanowires takes place under diffusion control. Current transients reveal that nucleation mechanism is instantaneous with a three-dimensional growth process. The transition-time measurements show that the gold elecrodeposition occurs as one-electron valence involved in the reaction mechanism. Charge transfer coefficient is also found to be 0.67 ± 0.01. The value... 

Abstract: The electrodeposition of platinum nanoparticles (PtNPs) on multiwall carbon nanotubes (MWCNTs)/fluorine-doped tin oxide glass (FTO) was investigated. Nucleation and growth mechanisms were studied via Scharifker and Hills model. Chronoamperometry results clearly show that the electrodeposition processes are diffusion-controlled and the diffusion coefficient is 1.5×10-5cm2/s. The semi-spherical particles with lamellar morphology were observed in 1M H 2SO 4, while a petal shape was discerned in 0.5M H 2SO 4. Also, dispersion, size, and uniformity of PtNPs were investigated, where the finer distribution of PtNPs with the average size less than 100 nm was obtained in 0.5M H 2SO 4... 

Electrochemical deposition of aluminum and lead from basic molten AlCl3-NaCl-KCl mixture on an aluminum electrode at 180 °C was studied by the methods of voltammetry, potential and current transient and constant current deposition. The deposition of aluminum was found to proceed via a nucleation/growth mechanism, while the deposition of lead was found to be diffusion controlled. The diffusion coefficient calculated for Pb2+ ions in basic melt by voltammetry was in agreement with the deductions of transient method. The analysis of the chronoamperograms indicates that the deposition process of lead on Al substrates was controlled by 3D diffusion control, nucleation and growth. The processes... 

Despite their potential applications, a limited number of studies for synthesizing vertical MoS2 nanoflakes especially via CVD have been reported so far, which generally involve tedious complex- and/or multi-step growth processes. In this study, direct synthesis of vertical MoS2 nanoflakes grown on the SiO2/Si substrate during a rapid sulfidation process by CVD method has been reported. Material characterization was performed using Raman spectroscopy, XRD and FE-SEM. The XRD results indicated the dominant phase of 2H–MoS2 within the synthesized layers. The characteristic distance between the two dominant peaks of E1 2g and A1g in the Raman spectra confirms the multi-layered structure for... 

In this study, biocompatible ceramic layers containing TiO2 and hydroxyapatite (HA) nanoparticles (TiO2/HA) were deposited on pure commercial titanium (Grade 2) by using plasma electrolytic oxidation and AC power supply. The coating process was carried out in five different solutions for various times at a current density of 500 mA cm−2. To achieve the optimum conditions for thickness and microstructure, the coating process was conducted in solutions with a 3 g L−1 concentration of HA nanoparticles. FESEM, XRD, and FTIR results showed that HA nanoparticles were successfully incorporated into the pores of the layer. Furthermore, the corrosion behavior of the coating layers in the simulated... 

In this work we report a fast two-step microwave activated synthesis of the ZnS:Mn nanocrystals. Zn(NO3)2 and Na2S 2O3 were used as the precursors and Mn(NO 3)2 was employed as the source of the impurity. The aqueous synthesis was based on the heat sensitivity of Na2S 2O3, which releases some S species on heating. Consequently, the reaction was well activated under microwave irradiation resulting in formation of ZnS:Mn nanocrystals. Thioglycerol (TG) was also used as the capping agent and the catalyst of the reaction. The synthesis process was done in two steps, i.e. 1 min irradiation without TG and then injection of TG and continuation of irradiation. ZnS:Mn nanocrystals were quickly formed...