Sharif Digital Repository

In this research, low density polyethylene (LDPE) and poly ethylene-co-vinyl acetate (EVA) were used as polymeric materials. The methods used to produce LDPE and EVA was Film Blowing and ThermalDry Phase Inversion. The amount of permeability, diffusivity and solubility of O2 and CO2 through above polymers were obtained and also the effect of temperature, pressure and film thickness for LDPE was measured. The Barometric method was considered and measurements were based on ASTM standard. To study film cross-section morphology in EVA, Scanning Electron Microscopy (SEM) was applied. From results we considered that the amount of permeability and solubility were decreased by increasing film... 

Polymer films possess excellent optical properties, such as high transparency, and thermal characteristics, like low heat conductivity, as well as further polymer specific advantages. Consequently, polymer films have an outstanding potential for many solar applications. They are already used for encapsulation of photovoltaic (PV) cells, as convection barrier in solar collectors and as substrate or adhesive layers for glazing. In translucent polymers, energy can be transferred internally by radiation in addition to conduction. Since radiant propagation is very rapid, it can provide energy within the layer more quickly than diffusion by heat conduction. Thus, the transient thermal response of... 

In dye-sensitized solar cells recombination reactions at the TiO2 photoanode with the electrolyte interface plays a critical role in cell efficiency. Recombination of injected electrons in the TiO2 with acceptors in the electrolyte usually occurs on uncovered areas of TiO2 surfaces. In this work, we report electropolymerization of polymer films on nanoporous TiO2 electrode surfaces using an ionic liquid as the growth medium. The choice of ionic liquid as the growth medium for this study is based on the insolubility of dye N719 in this electrolyte, thus avoiding dye molecule detachment from the TiO2 photoanode surface over the entire potential range investigated during the... 

Abstract A sensitive electrochemical sensor for determination of phenothiazine (PTZ) was introduced based on molecularly imprinted polymer (MIP) film. A computational study was performed to evaluate the template-monomer geometry and interaction energy in the prepolymerization mixture. The electrode was prepared during electropolymerization of pyrrole (Py) on a pencil graphite electrode (PGE) by cyclic voltammetry (CV) technique. The quantitative measurements were performed using differential pulse voltammetry (DPV) in Britton-Robinson (BR) buffer solutions using 60% (v/v) acetonitrile-water (ACN/H2O) binary solvent. The effect of important parameters like pH, monomer... 

This work was intended to develop a new cross-linked gelatinized starch-xanthan gum hydrogel system, to characterize the properties of the new material, and to explore its potential applications in controlled drug delivery. Cross-linked starch-xanthan gum polymers were synthesized with varying levels of xanthan gum and sodium trimetaphosphate (STMP). The reaction of starch-xanthan gum polymers with STMP was examined using solid 31P NMR spectroscopy and FTIR. Morphology of the films made from the new polymers was studied by scanning electron microscopy. The swelling properties and the network parameters such as gel mesh size of the films were investigated. The permeation of solutes with... 

Polymer composite films based on chitosan (CS) and nanodimaond (ND) were prepared using solution casting method. ND with variable contents of carboxylic functional group was prepared using thermal oxidation at temperature of 420 °C under air atmosphere at various durations of 1.5 and 4.5 h. The interfacial interaction between NDs and CS and morphological evolution of CS in presence of NDs were investigated by Fourier transform infrared (FTIR), differential scanning calorimeter (DSC) and X-ray diffraction (XRD) analyses. A significant improvement in tensile strength (∼85%) and tensile modulus (∼125%) of CS was achieved by oxidized ND (OND) obtained at higher oxidation time of 4.5 at low... 

A study has been carried out of the effect of an anodizing pre-treatment in a sulphuric acid electrolyte on the strength of AA 5052 alloy/polypropylene joints prepared using friction stir spot welding. Lap-shear tests were used to determine the joint strength. Comparisons were made with joints pre-treated using sand blasting. The failed specimens were examined by scanning and transmission electron microscopy. Anodizing improved the strength of the joints by a factor of about 6 compared with sandblasting. For the anodizing pre-treated joints, melted polymer infiltrated deeply within the nanoporous anodic film, forming a strong polymer-film bond. Joint failure occurred by ductile tearing of... 

In this study, zirconia antistatic coatings were synthesized by a simple dip coating sol-gel route on glass substrates, then applied to polymer-based composites to potentially improve their dust or water repellent capabilities. The coating solution contained a precursor (ZrCl4), solvent (isopropanol) and coupling agent. FTIR spectra confirmed ZrO2 and ZrO compounds in both solution and antistatic coating. FE-SEM images indicated ZrO2 fibers’ thickness was controlled by changing ZrCl4 concentration (150 g–15 g ZrCl4/l) or relative humidity (20%–60%) during coating drying. Fibers grew thicker when decreasing the former or increasing the latter. The surface electrical resistivity for all... 

A series of polyurethane elastomers (PUEs) based on 4,4′-cyclohexamethylene diisocyanate (H12MDI)/1,2-ethanediol as hard segment with the soft segments having different molecular weights of polycaprolactone diols, were effectively polymerized by two step technique. The structural characterization was performed by FT-IR spectroscopy. The X-ray diffraction (XRD) technique was used to study the crystallinity and hydrophilicity of the prepared polymer films. It was found that crystallinity and hydrophilicity increased with increasing the chain length of soft segments. The effect of molecular weight of polyols on the contact angle, water absorption (%) and swelling behavior of the synthesized... 

TiO2 nanotubes (TNTs) were synthesized hydrothermally and modified by Cu2O using a sol-gel method to provide photocatalytic activity in visible light. Cellulose nanofiber (CNF)-based films were prepared by adding TiO2, TNTs, and Cu2O-modified TNT (TNT-Cu2O). The TiO2-based nanoparticles (TiO2, TNTs, and TNT-Cu2O) were uniformly distributed in the base polymer to make compatible and flexible films. The incorporation of nanoparticles significantly enhanced the UV-shielding properties of the film while slightly decreasing the transparency. Incorporating nanofillers improved the film's mechanical and water resistance properties depending on the nanoparticle type. The TNT-Cu2O-added CNF film... 

A fiber coating from polyaniline (PANI) was electrochemically prepared and employed for solid phase microextraction (SPME) of some polycyclic aromatic hydrocarbons (PAHs) from water samples. The PANI film was directly electrodeposited on the platinum wire surface in sulfuric acid solution using cyclic voltammetry (CV) technique. The applicability of this coating was assessed employing a laboratory-made SPME device and gas chromatography with mass spectrometry (GC-MS) for the extraction of some PAHs from the headspace of aqueous samples. Application of wider potential range in CV led to a PANI with more stability against the temperature. The homogeneity and the porous surface structure of the... 

Microfluidic systems (MFS) provide a range of advantages in biomedical applications, including improved controllability of material characteristics and lower consumption of reagents, energy, time and money. Fabrication of MFS employs various materials, such as glass, silicon, ceramics, paper, and metals such as gold, copper, aluminum, chromium and titanium. In this review, gold thin film microfluidic channels (GTFMFC) are discussed with reference to fabrication methods and their diverse use in chemical and biomedical applications. The advantages of gold thin films (GTF) include flexibility, ease of manufacture, adhesion to polymer surfaces, chemical stability, good electrical conductivity,...