Sharif Digital Repository

Polyvinyl acetate (PVAc) nanocomposites for wood adhesives containing different amounts of colloidal silica nanoparticles (CSNs) were synthesized via in situ one-step emulsion polymerization. The adhesion strength of wood specimens bonded by PVAc nanocomposites was investigated by the tensile test. Thermal properties of PVAc nanocomposites were also characterized by differential scanning calorimetry and thermogravimetric analysis. Rheological and morphological properties of the PVAc nanocomposites were investigated using rheometric mechanical spectrometry and field emission scanning electron microscopy (FESEM), respectively. The obtaining results showed that the shear strength of PVAc... 

In this research, low density polyethylene (LDPE) and poly(ethylene-co-vinyl acetate) (EVA) were used as polymeric materials. The methods used to produce LDPE and EVA was film blowing and thermal-dry phase inversion. The amount of permeability, diffusivity and solubility of O2 and CO2 through above polymers were obtained and also the effect of temperature, pressure and film thickness for LDPE was measured. To study film cross-section morphology in EVA, scanning electron microscopy (SEM) was applied. The results showed that the amount of permeability and solubility were decreased by increasing film thickness but diffusivity was increased. However, by increasing temperature, permeability,... 

A detailed pseudo-bulk model has been used for prediction of conversion and particle size distribution (PSD) of vinyl acetate in a continuous emulsion polymerization reactor. Finite volume (FV) and moment techniques are applied for solving population balance equation under continuous operation. It is found that both methods can predict sustained oscillations in the monomer conversion, however the FV method matches the experimental data better than the moment method. The monomer conversion and free surfactant concentration are controlled via two single control loops. In this work, a new control strategy for controlling monomer conversion has been proposed. It has been shown that monomer... 

In this research, the effects of preparation conditions, including the coagulation bath temperature, polymer solution composition, preliminary drying time, and thickness of cast polymeric films, on the morphology of ethylene/vinyl acetate copolymer membranes were investigated with scanning electron microscopy and nitrogen gas permeability tests. Flat sheet membranes were prepared through a thermal-wet phase-inversion method. Scanning electron microscopy pictures showed asymmetric structures for some of the membranes. It was also observed that the porosity of the membranes decreased with an increase in the temperature of the coagulation bath and the solvent evaporation period. When the... 

Industrial scale continuous stirred tank reactor (CSTR) for production and grade transitions of poly vinyl acetate (PVAc) at the different reactor sizes was investigated. Such reactor is known to show oscillatory behavior and to have periodic limit points, particularly at high molecular weights. Four efficient novel hybrid optimization methods which use variable population size genetic algorithm (VPGA), bacterial optimization algorithm (BO) and shuffled frog leaping method (SFL) were introduced for this kind of reactors. These algorithms can reliably find dynamically stable points with desired conditions for PVAc production. The dynamic modeling combined with the new hybrid optimization... 

In the present work, graphene oxide (GO) and reduced graphene oxide (RGO) were incorporated at low-density polyethylene (LDPE)/ethylene vinyl acetate (EVA) copolymer blend using solution casting method. Monolayer GO with 1-nm thickness and good transparency was synthesized using the well-known Hummers's method. Fourier transform infrared and X-ray photoelectron spectroscopy data exhibited efficient reduction of GO with almost high C/O ratio of RGO. Scanning electron microscopy showed the well distribution of GO and RGO within LDPE/EVA polymer matrix. The integrating effects of GO and RGO on mechanical and gas permeability of prepared films were examined. Young's modulus of nanocomposites are... 

2,4,6,8,10,12-Hexanitro-2,4,6,8,10,12-hexaazaisowurtzitane (2,4,6,8,10,12-hexanitro-2,4,6,8,10,12-hexaazatetracyclo dodecane (CL-20)-based polymer/plastic bonded explosives are used in propellant formulation. It can be predicted that CL-20-based nano-polymer/plastic bonded explosives are able to have reduced composite sensitivity and superior mechanical strength. In the current study, we have prepared two kinds of CL-20-based nano-polymer/plastic bonded explosives with ethylene-vinyl acetate copolymer and glycidyl azide polymer via the microemulsion method. Several visual techniques such as SEM/AFM/TEM techniques have been utilized for complete characterization of CL-20-based... 

Ethylene vinyl acetate/graphene oxide (EVA/GO) nanocomposite films were prepared via solution casting method. The morphological studies investigated using SEM and XRD methods and the results confirmed the formation of likely exfoliation structures and good interaction between matrix and fillers. The results of permeability measurements showed that films have good resistance against oxygen. Mechanical measurements revealed that Young’s modulus and tensile strength of EVA have improved with introducing GO because of proper dispersion of GO into matrix and good interaction between them; however, elongation at break decreased due to formation of strong and rigid polymer/filler network preventing... 

A magnetic nanoparticle@starch-g-poly(vinyl sulfate) nanocomposite (MNP@St-g-PVS) as a new magnetic nano-adsorbent has been prepared based on graft copolymerization of vinyl acetate onto starch in the presence of magnetic nanoparticles, where the acetate groups were converted to hydroxyl groups followed by the sulfation of the hydroxyl groups using chlorosulfonic acid. Characterization of this magnetic nanocomposite was carried out by FTIR, TGA, XRD, VSM, SEM, TEM and elemental analysis. The resulting nanocomposite was used as an adsorbent for the removal of typical cationic dyes, methylene blue (MB) and malachite green (MG), from aqueous solutions. All experimental parameters that can... 

In this article, oxygen barrier properties of nanocomposite films composed of organoclay (OC), high-density polyethylene (HDPE), and ethylene vinyl acetate (EVA) copolymer have been investigated. The nanocomposite films whose EVA forms a dominant fraction were prepared using the solution method. The dispersion of the OC in the HDPE/EVA blend was improved through taking two-step procedure in the preparation of nanocomposite. First, the OC and EVA were dissolved in chloroform. Then, the resulting product, after evaporating most of the solvent, along with HDPE was dissolved in xylene. The obtained nanocomposite films underwent a number of tests in order to examine their barrier properties... 

The simultaneous control of the molecular weight, separation, and purification of polyvinyl acetate was achieved using a cobalt-mediated radical polymerization (CMRP) in a packed column with silica gel particles (PC-CMRP). The controlled radical polymerization of VAc in the packed columns was evaluated from the linear time dependence of Ln[M]0/[M], linear increase of molecular weight with the increase in conversion, and narrow molecular weight distribution. PC-CMRP method was used to produce high-purity polymers with controlled molecular weight and narrow molecular weight distribution without requiring additional purification steps. The high ability of silica gel particles to adsorb free... 

A high sensitive upper critical solution temperature (UCST) copolymer was synthesized through free radical copolymerization with acrylamide (AAm) and vinyl acetate (VA). The UCST behavior is due to a combination of hydrogen bonds and electrostatic potentials between copolymer chains. Turbidimetry, dynamic light scattering, and rheology studies were used to determine the phase transition and aggregation behavior. It is indicated that copolymer with 80% AAm has a phase transition temperature between 38 and 38.2 °C, which is suitable for releasing fever medicine. Also, the temperature gradient for the complete dissolution of the copolymer is 2 °C. The molecular dynamics simulations at a... 

Nanocomposite films based on low density polyethylene (LDPE), containing of 2, 3, and 4. wt.% organoclay (OC) and ethylene vinyl acetate (EVA) copolymer as a new compatibilizer were prepared and characterized using rheological tests, X-ray diffraction, differential scanning calorimetry, oxygen permeation measurements, and tensile tests. There was no exfoliation or intercalation of the clay layers in the absence of EVA, while an obvious increase in d-spacing was observed when the samples were prepared with EVA present. This issue was reflected in the properties of nanocomposites. The oxygen barrier properties of the LDPE/EVA/OC film were significantly better than those of the LDPE/OC film.... 

In this study, the effect of film preparation conditions on the gas permeation properties of polyethylene (PE) and ethylene vinyl acetate (EVA) films (containing 18 and 28wt% vinyl acetate) was investigated. Film blowing and phase inversion methods were applied in the production of PE and EVA films, respectively. The permeation of pure oxygen and carbon dioxide gases was measured at room temperature. The results indicated that with the increase of PE film thickness, permeability and solubility of O2 and CO2 in these films decreased; but the diffusivities of gases through PE films increased. In addition, in the case of EVA copolymers, by increasing the content of vinyl acetate, the... 

In this research, polypropylene (PP) nanocomposite films were prepared by melt intercalation method and their properties have been evaluated. To facilitate the formation of either intercalated or exfoliated nanocomposites, ethylene vinyl acetate copolymer (EVA) was used as a compatibiliser. Morphology of composites was determined by X-ray Diffraction (XRD) and transmission electron microscopy (TEM). XRD and TEM analyses confirmed that increasing of EVA content leads to achievement of intercalated nanocomposites. Furthermore, differential scanning calorimetry (DSC) measurement indicated a decrease in crystallinity, melting point and crystallization temperature. Also, permeability tests showed...