Sharif Digital Repository

When a multistage manufacturing process is monitored statistically, the cascade property results in a more complicated condition compared to the case when a single-stage process is controlled. The cascade property usually exists in different stages of a multistage process, where the quality of a stage influences the performance of the next stage. Moreover, sometimes the quality of a product/process is best characterized by a functional relationship. This relationship is referred to as a profile. In this paper, phase I monitoring of simple linear profile is addressed for a multistage process involving the cascade property. To aim this, the capabilities of the methods that may be used to... 

When a multistage manufacturing process is monitored statistically, the cascade property results in a more complicated condition compared to the case when a single-stage process is controlled. The cascade property usually exists in different stages of a multistage process, where the quality of a stage influences the performance of the next stage. Moreover, sometimes the quality of a product/process is best characterized by a functional relationship. This relationship is referred to as a profile. In this paper, phase I monitoring of simple linear profile is addressed for a multistage process involving the cascade property. To aim this, the capabilities of the methods that may be used to... 

Monitoring the respiratory signal is crucial in many medical applications. Traditional methods for the respiration measurement are normally based on measuring the volume of air inhaled and exhaled by lungs (like spirometer) or oxygen saturation in blood. However, these methods have numerous challenges including their high cost and not being accessible in some cases. In this paper, an algorithm for deriving the respiratory signal from ECG signal is proposed, which is based on other proposed algotithms. This algorithm uses the cubic spline interpolation (CSI) of R-waves in ECG to derive the respiratory signal. The CSI algorithm is made efficient with respect to ECG features in order to reduce... 

In this paper, the Monte Carlo technique is used to determine the optical detection strategies in three-layered (maternal, amniotic fluid and fetal) tissue model. This model is utilized to estimate the transabdominal optical power and optimum source-detector (S-D) separation. Results based on the launching of 2 million photons with 1 mW optical power showed that the expected optical power output is in the range of 10 -6-10 -10 W/cm 2 depending on S-D separation. Considering the limit of the signal processing methods (such as adaptive noise cancelling) and the use of silicon photodetector, an S-D separation of 4 cm has been selected as a practical compromise between signal level and... 

The principle, configuration, and the special features of a stable platform digital controller are presented in this paper. The main goal of this paper is replacing an analog controller with its awaiting digital one. This has been done using TMS320LF2402 digital signal processor which offers the enhanced TMS320 DSP architectural design of the C2xx core CPU for low-cost, low-power, and high-performance processing capabilities. The experimental results show that the digital controller is identical to the analog one and can be a suitable replacement for the analog controller. Copyright © 2008 by Department of Electronics, AGH University of Science and Technology  

In this paper, a reliable low power single phase grid-connected inverter for photovoltaic modules is proposed. The inverter has improved lifetime since large electrolytic capacitor is replaced with small film capacitor due to circuit topology, power processing and proper control scheme. Thus the main limiting component in single phase grid connected inverters is obviated. The proposed inverter consists of two power processing stages. First a dual active bridge (DAB) converter boosts the voltage of PV panel to approximately 440 V and eliminates impact of high dc bus voltage ripples. A proper feed forward control is proposed to regulate the dc bus voltage with high ripple. Simulation results... 

This paper addresses the feasibility of applying realtime steganalysis to the Internet data. To reach a practical solution, we have employed offline procedures to minimize the volume of the data to be processed by an online real-time system. Possible offline services that can be provided to an online system then led us to appropriate network designs for the online system. To go into detail of the online systems, we have carefully analyzed some well-known, state-of-the-art steganalysis algorithms and estimated their processing power and memory requirements. Some formulas are derived to relate the network bit rate with the number of the processing units, their processing power, and memory... 

Share of leakage in total power consumption of static RAM (SRAM) memories is increasing with technology scaling. Reverse body biasing increases threshold voltage (Vth), which exponentially reduces subthreshold leakage, but it increases SRAM access delay. Traditionally, when all cells of an SRAM block used to have almost the same delay, within-die variations are increasingly widening the delay distribution of cells even within a single SRAM block, and hence, most of these cells are substantially faster than the delay set for the entire block. Consequently, after the reverse body biasing and the resulting delay rise, only a small number of cells violate the original delay of the SRAM block; we... 

Ethylene dichloride thermal cracking is one of the conventional methods for hydrogen chloride production. A critical issue concerned with this method is to provide thermal energy for cracking reaction, which is generally provided by the flammable gasses inside the furnace. Utilizing renewable energy sources can be an interesting topic in this case. Hence, in this paper, the thermal integration feasibility of an ethylene dichloride cracking unit with a hybrid renewable plant, based on geothermal and wind energies, is investigated, while the case study for wind turbines system (Alstom ECO 74/1670/ Class II model) is Meshkin Shahr, located in Iran. To utilize geothermal energy, a...