Sharif Digital Repository

High voltage power supplies are widely used in telecommunication systems. To better utilize these power supplies, voltage should be stabilized at a certain level. In this application, in case of changing voltage, the desired output parameters will change, such as RF output power quality. Various methods have been proposed to stabilize the voltage at acceptable levels. One of the most commonly used methods is use of switching regulators that are considered for high efficiency in comparison with linear regulators. But the use of these regulators also has problems. One of these problems is electromagnetic interference which is very important in telecommunication systems. Therefore, the need for... 

In this paper, a novel droop method to control the power sharing of parallel uninterruptible-power-supply (UPS) systems is presented. In a clear-cut contrast to the previously reported works, the controller is a proportional-resonant controller which ensures good transient response and steady-state objectives. Furthermore, the need for sensing the output current for the power-sharing control is removed by implementing it in a software routine. This brings a less complicated and less expensive structure in which the number of feedback sensors is reduced from three to two. The droop paralleling strategy is based on the drop in the inverter output frequency and amplitude. The application of... 

LLC resonant converter has been widely used in dcdc converters. In this paper, optimum dead-time and maximum switching frequency of a wide-adjustable-range LLC resonant converter are investigated for realizing the zero voltage switching (ZVS) operation even under the worst-case conditions. Analyses demonstrate that these parameters depend on the converter inductance ratio and ratio of the converter resonant capacitor and the effective capacitance appeared in parallel with the drainsources of the power MOSFETs. The necessary dead time for realizing the ZVS operation can be minimized by choosing the normalized maximum switching frequency, properly. Using the dead-time optimum value, soft... 

Clamp mode snubbers are very well suited for the series structure of the insulated-gate bipolar transistors (IGBTs) in pulsed power applications. They properly meet the necessities expected from them such as the fast operating of the series IGBTs since they have no effect on the gate side. In addition, they can provide safe voltage condition for the IGBTs in short circuit faults, which are very probable in pulsed applications. The clamp mode snubber can perform its voltage balancing task whenever the power capacity of the snubber can support the injected powers due to the voltage unbalancing factors. This paper initially introduces the main factors injecting power to the snubbers. Then, it... 

Isolated, high-density DC-DC converters play a crucial role in the power supply unit of information technology industries. By virtue of high efficiency and high power density, LLC resonant converters-among the rest of DC-DC converters-are suitable candidates for this application. The magnetic structure of this converter, however, is a bulky, dissipative part, which has a considerable portion of power loss. Improvement in the size and efficiency of the LLC transformer will lead to an overall enhancement of power density and efficiency of the converter. Nevertheless, the optimization of planar transformers for the LLC converter has not been studied enough. This paper proposes a... 

Background: The aim of this study was to assess the performance of an original powered foot clearance creator (PFCC) mechanism worn in conjunction with an isocentric reciprocal gait orthosis (IRGO) and evaluate its effect on trunk compensatory movements and spatiotemporal parameters in nine healthy subjects. Method: A PFCC motorized mechanism was designed that incorporated twin sole plates, the movements of which enabled increased toe to floor clearance during swing phase. A prototype was constructed in combination with an IRGO, and hence was re-named as an IRGO-PFCC orthosis. The effects of IRGO-PFCC usage on the spatiotemporal parameters and trunk compensatory movements during walking were... 

In switching power supplies, the transformer leakage inductance (TLI) is of considerable practical significance. Ordered winding is the certain assumption in previously reported works for the calculation of the TLI value. However, disordered windings are usually unavoidable in practice and their effect on the value of the TLI is considerable. The problem becomes more complex when the number of winding turns increases. In this paper, the effect of winding disorder on the TLI value is investigated. In disordered wrapping, the winding turns arrangement (WTA) of each produced transformer is different from the others. Thus, each produced transformer has an exclusive TLI value in a disordered... 

The lack of turn-off ability makes the spark gap-based Marx generator uncontrollable in terminating the output pulse. In addition, there are some limitations for rise time and voltage gain improvements in the conventional critically-damped Marx design. In this paper, an efficient over-damped design of Marx circuit is proposed, which leads to a shorter rise time as well as a larger voltage gain. A chopping magnetic switch is employed to achieve the desired values of the fall time and full width at half maximum (FWHM). Moreover, adding a DC bias circuit to the magnetic switch provides the ability to adjust the pulse FWHM parameter. Therefore, an output pulse with a shorter rise time, larger... 

Applying series configuration of the insulated gate bipolar transistors (IGBTs) to the pulsed power supplies offers unique features such as compactness and long life time. In the high-voltage pulsed power supplies, a large number of the IGBTs are required to be serially connected. Hence, the safe operating condition provision for the series IGBTs is an important and crucial issue. The effect of the voltage unbalancing factors becomes remarkable when the number of switches in the series structure increases. There are passive and active methods to balance the voltage of the series IGBTs. In both of these methods, an amount of power must be dissipated to remove the effect of the voltage...