Sharif Digital Repository

Convection heat transfer below a horizontal, hot, and isothermal strip of infinite length and width of 2L embedded in fluids with different Prandtl number (Pr) and Nusselt number (Nu) is analyzed with the aid of integral method. A new concept is utilized to determine the boundary layer thickness at the strip's edge, which is based on matching the flow rate of the boundary layer below the strip at its edge and the flow rate of the plume, which forms after the heated fluid detaches from the strip's edge. In addition to these novelties, a numerical model is developed to verify the analytical framework, and an excellent agreement is observed between the analytical and numerical models  

The laminar natural convection from an isothermal horizontal cylinder confined between vertical walls is investigated by experimental and numerical methods. The experimental and numerical data are well correlated, independently, to equations which give the average Nusselt number in terms of the wall spacing to cylinder diameter ratio, t/D, and the Rayleigh number, Ra, for two different values of the wall height to cylinder diameter ratios, H/D=7 and 15.2. For the low Rayleigh numbers considered (Ra<1000), there are certain conditions for the confining walls under which heat transfer from the cylinder is maximum. Results are compared with the reported numerical and/or experimental results... 

A new perspective suitable for understanding the details of nonlinear pumping (formation of traveling shocks) inside a pressurized cavity is constructed in this paper. Full compressible axisymmetric three-dimensional Navier-Stokes equations are used as the starting point to cover all complexities of the problem that exceedingly increase for particular ranges of Mach, Reynolds and Prandtl numbers. Then a very high-order numerical method is introduced to preserve the user-defined order of accuracy for practical simulations. For removal of spurious waves, higher-order compact filters are derived. All equations are marched in time using the classical Runge-Kutta algorithm which is appropriate... 

The absorber is an important component in absorption machines and its characteristics have significant effects on the overall efficiency of absorption machines. This article reports on the results of numerical studies on the characteristics of falling film LiBr-H2O solution on a completely wetted horizontal tube and the associated vapor absorption in the Reynolds number range of 5 < Re < 100. The boundary layer assumptions are used for the transport of mass, momentum and energy equations and the finite difference method is employed to solve the governing equations in the film flow. The heat and mass transfer coefficients are expressed in the forms of Reynolds number, Prandtl number and... 

In this study, the unsteady three dimensional nanofluid flow, heat and mass transfer in a rotating system in the presence of an externally applied uniform vertical magnetic field is investigated. This study has different applications in rotating magneto-hydrodynamic (MHD) energy generators for new space systems and also thermal conversion mechanisms for nuclear propulsion space vehicles. The important effects of Brownian motion and thermophoresis have been included in the model of nanofluid. The governing equations are non-dimensionalized using geometrical and physical flow field-dependent parameters. The velocity profiles in radial, tangential and axial directions, pressure gradient,... 

In this study, the unsteady three dimensional nanofluid flow, heat and mass transfer in a rotating system in the presence of an externally applied uniform vertical magnetic field is investigated. This study has different applications in rotating magneto-hydrodynamic (MHD) energy generators for new space systems and also thermal conversion mechanisms for nuclear propulsion space vehicles. The important effects of Brownian motion and thermophoresis have been included in the model of nanofluid. The governing equations are non-dimensionalized using geometrical and physical flow field-dependent parameters. The velocity profiles in radial, tangential and axial directions, pressure gradient,... 

In this work, a solution is applied to investigate the heat transfer characteristics in a pipe with turbulent decaying swirling flow by using the boundary layer integral scheme. The governing equation is solved using the forth-order Runge-Kutta scheme resulting in thermal boundary-layer thickness and dimensionless heat transfer coefficient, namely, the Nusselt number. Both forced- and free-vortex profiles are considered for the tangential velocity component. A comparison of the results obtained for the Nusselt number with available experimental data shows that this scheme has good capability in predicting the heat transfer parameters of swirling flow especially in the entrance region of a... 

This essay investigates a steady three-dimensional laminar boundary layer flow of magnetohydromagnetic radiative of graphene oxide-water nanofluid over an extensible surface in the attendance of couple stress, thermal ray, and Joule heating impact. Governing equations are solved numerically using the Runge-Kutta-Fehlberg 4.5 approach after the transformation of partial differential equations into ordinary differential equations. The main goal of this essay is to check the impacts of variations in the value of numerous parameters on the velocity along x and y-axis directions ((Formula presented.)) and temperature ((Formula presented.)) profiles, and also on the local skin friction coefficient... 

In the present study, a new swirling flow generator is studied which aims to enhance the convective heat transfer rate in a heat exchanger tube. This device has a four-point star cross section. The study mainly investigates the effect of swirl generator on heat transfer rate and pressure drop along the test tube which is under a constant and uniform heat flux. The working fluid in the experiments is the water–ethylene glycol mixtures with Prandtl numbers ranging from 5 to 150 at different Reynolds numbers from 12,000 to 27,000. The results clarify the potential of the applied swirl generator to make a significant enhancement in the heat transfer rate with a satisfactory rise in the pressure... 

In the present study, a new swirling flow generator is studied which aims to enhance the convective heat transfer rate in a heat exchanger tube. This device has a four-point star cross section. The study mainly investigates the effect of swirl generator on heat transfer rate and pressure drop along the test tube which is under a constant and uniform heat flux. The working fluid in the experiments is the water–ethylene glycol mixtures with Prandtl numbers ranging from 5 to 150 at different Reynolds numbers from 12,000 to 27,000. The results clarify the potential of the applied swirl generator to make a significant enhancement in the heat transfer rate with a satisfactory rise in the pressure... 

The aim of present study is to investigate the convective heat and mass transfer in steady MHD boundary layer flow of an electrically conducting micropolar fluid over an inclined surface. Partial differential equations resulting from the mathematical modeling of the phenomenon are reduce to nonlinear ODEs, and a finite difference based scheme has been adopted to iteratively find the numerical solution by employing the successive over-relaxation (SOR) method. A self-developed computer code has been used in the MATLAB environment. Influence of chemical reaction, Brownian motion, thermophoresis, and viscous dissipation on the relevant features of the flow are discussed and analyzed through... 

The aim of present study is to investigate the convective heat and mass transfer in steady MHD boundary layer flow of an electrically conducting micropolar fluid over an inclined surface. Partial differential equations resulting from the mathematical modeling of the phenomenon are reduce to nonlinear ODEs, and a finite difference based scheme has been adopted to iteratively find the numerical solution by employing the successive over-relaxation (SOR) method. A self-developed computer code has been used in the MATLAB environment. Influence of chemical reaction, Brownian motion, thermophoresis, and viscous dissipation on the relevant features of the flow are discussed and analyzed through...