Sharif Digital Repository

A new structure for the compression surfaces of a supersonic inlet is proposed which has improved the target performance parameter i.e. total pressure recovery ratio. This idea resulted in development of a new type of supersonic inlet, utilized four ramps and a cone simultaneously as the compression surfaces. A prototype of the proposed inlet has been designed for a free stream Mach number of 3 and its performance has been evaluated via numerical simulation for both design and off-design conditions. The performance of the newly designed inlet has been compared to the existing experimental data of two double-cone inlets. The acquired data are further compared with analytical calculations of... 

The performance of an axisymmetric supersonic mixed-compression air intake has been investigated experimentally. The intake has been designed for free stream Mach number of 2.0. This study has two main goals, firstly to investigate the performance of the intake without boundary-layer bleed in design and off-design conditions and secondly to study the effects of a slot bleed on the intake performance. The intake has been tested at free stream Mach numbers of 1.8, 2.0, and 2.2 and zero degree angle of attack. Total pressure recovery (TPR), mass flow ratio (MFR) and flow distortion (FD) have been selected parameters to assess the intake performance. The bleed slot is located upstream of the... 

The performance and the buzz onset of a supersonic mixed-compression axisymmetric intake are experimentally investigated. Effectsof the slot bleed position, angle, and width onthe intake performance and onthe buzz initiation at three different Mach numbers of 1.8, 2.0, and 2.2 and at a zero degree angle of attack are studied. The intake performance is assessed using the total pressure recovery, mass flow ratio, flow distortion, and bleed mass flow ratio. The results show that applying the bleed at a position near the intake entrance and reducing the bleed entrance slant angle and width all improve the intake performance considerably. Moreover, these parameters postpone the buzz onset. In... 

In this research the design methods of radial flow compressor volutes are reviewed and the main criterions in volute primary designs are recognized and most effective ones are selected. The effective parameters i.e. spiral cross section area, circumferential area distribution, exit cone and tongue area of the compressor volute are parametrically studied to identifythe optimum values. A numerical model is prepared and verified through experimental data which are obtained from the designed turbocharger test rig. Different volutes are modeled and numerically evaluated using the same impeller and vane-less diffuser. For each model,the volute total pressure ratio, static pressure recovery and... 

This research numerically and experimentally investigates a small turbocharger radial flow compressor with a vane-less diffuser and volute. The geometry of the compressor is obtained via component scanning, through which a 3D model is prepared. The flow inside this model is numerically analyzed by using a Navier-Stokes solver with a shear-stress transport turbulence model. The characteristic curves of the compressor and the contributions of its components to total pressure drop are acquired by measuring the static and total pressures at different cross sections of the compressor. Numerical results are verified with the experimental test results. The model results exhibit good agreement with... 

A computational fluid dynamics code was developed to compute the flow inside and around a supersonic external compression axisymmetric intake. The code solves the Reynolds-averaged Navier-Stokes equations using an explicit finite volume method in a structured grid and uses the Baldwin-Lomax algebraic model to compute the turbulent viscosity coefficient. Experiments were performed to validate the predicted results and good agreements are achieved. In the next part of the research, a parametric study was undertaken using the designed base case at a constant Mach number of 2 and at 0° angle of attack. The effects of various important parameters such as free stream Mach number, spike deflection... 

The performance of a supersonic mixed compression air intake has been investigated experimentally. The intake is of axisymmetric one and has been designed for a free stream Mach number of 2.0. The present work has two main goals, first to investigate the performance of the intake without boundary layer bleed at design and at off-design conditions and second to study the effects of a bleed slot on the intake performance. The intake has been tested at free stream Mach numbers of 1.8, 2.0, and 2.2 and at zero degrees angle of attack. Total pressure recovery, mass flow ratio, and flow distortion have been selected to assess the intake performance. The bleed slot is located upstream of the intake... 

The S-shaped air intakes are very common shapes due to their ease in the engine-body integration or Radar Cross Section, RCS, specifications especially for fighter aircrafts. The numerical shape optimization of an S-shaped air intake using adjoint method is conducted. The flow of a specified air intake that uses S-duct M2129 is simulated using three dimensional (3D) numerical solution of Reynolds-Averaged Navier-Stokes equation along with k-ω SST turbulence model. The main purpose of this optimization scheme is to maximize the total pressure recovery (TPR). Further, the scheme is developed in such a way that would be applicable in industry thru satisfying specified constraint requirements.... 

Supersonic separators (3Ss) are applied in gas separation processes. Two-dimensional simulation is employed to investigate the effect of operational and thermophysical parameters on the shockwave position. In addition, the impact of the cyclonic part and wet outlet geometry is evaluated by proposing four cases. Increasing the length of the cyclonic part exerts positive and negative influences on the performance of the 3S and the pressure recovery coefficient, respectively. The optimum length is determined between 10 and 15 cm. To demonstrate negative effects of wasted air from the wet outlet, its flow has been increased from 3.6 to 8.1 % of the inlet flow. Improved performance of the 3S is... 

The performance characteristics of an axisymmetric inlet at its design and off-design operational conditions are experimentally investigated. The model is tested for wide ranges of free stream Mach numbers, M∞ = 1.5-2.5, and mass flow rates. For each test, the pressure recovery, the mass flow passing through the inlet and the pressure distribution over the spike and the cowl are measured. In addition, the shock wave formed in front of the inlet is visualized. The characteristic curve of the inlet is then obtained for each free stream Mach number. As the Mach number is increased, the pressure recovery is reduced, but the maximum value of the mass flow rate grows up. Variations of the mass... 

The flow over a supersonic inlet has been investigated experimentally and numerically at a free stream Mach number of 2 and a zero degree angle of attack. Wind tunnel tests were performed to obtain the performance parameters of the inlet and were used as a baseline and validation tools for the numerical code. A heat source was added to the flow field at a distance ahead of the inlet. The effect of heat source addition on the main performance parameters of the inlet is investigated numerically. Results show that the heat source considerably reduces drag coefficient; however, its effect on pressure recovery is not favorable. This unfavorable effect was then minimized by controlling heat source... 

Experiments were conducted to study various kinds of Shock wave/Boundary Layer Interaction (SBLI) in an axisymmetric mixed-compression inlet. Experimental findings were compared and verified by numerical solutions where possible. Different types of SBLI relevant to the mixed-compression inlets are classified. Interactions of normal shock wave/boundary-layer at subcritical condition and in buzz condition are investigated using Schlieren and shadowgraph flow visualization as well as unsteady pressure recordings. The data is compared with the CFD predictions. Interactions of cowl lip reflected oblique shock and the terminal normal shock with the spike boundary-layer at both critical and... 

The effects of geometrical scaling on a supersonic external compression axisymmetric inlet are investigated. Various lower and higher geometrical scales of supersonic inlet are considered as the case studies. The inlet flow is simulated numerically using RANS solver along with the SST k-w turbulence model. The numerical results are in an acceptable agreement with the NACA experimental data at free stream Mach number of 1.79 and at zero angle of attack. The results show that the static pressure distribution of the inlet flow experiences some differences for various scales especially at the regions of the flow entrance and throat area. The mean flow Mach number and the mass flow rate at the...