Sharif Digital Repository

Fabrication of organohalide perovskite materials on the top of ZnO nanoparticles (NPs) has some beneficial advantages such as room temperature processing; however, the perovskite is not stable on ZnO NPs layer during the annealing process. In fact, there are only a few reports about the fabrication of perovskite solar cells on ZnO NPs layer. Herein, the decomposition mechanism of CH3NH3PbI3 perovskite materials on ZnO is reported, and it is found that the perovskite film on the top of the ZnO layer is converted into PbI2 during the annealing process due to the existence of hydroxide groups on the surface of the ZnO NPs. Depending on the annealing temperature, the reaction rate and the... 

Herein, a simple and novel method was used to synthesize a new structure of graphene which can be called hollow graphene. First, the ZnO-Graphene QDs synthesized by solution method and then ZnO QDs were dissolved from this structure using an acidic solution to obtain hollow structure of graphene. Afterward, this structure was used in PbS QDs solar cell in order to improve the transport of electron and decrease the recombination of the carriers. A power conversion efficiency of 5.3% was obtained using hollow graphene as a fast electron extraction layer due to the enhancement of EQE and current density. The improvement of PCE in this device was corresponded to efficient photosensitized... 

TiO2 nanorod layers are synthesized by simple chemical oxidation of Ti substrates. Diffuse reflectance spectroscopy measurements show effective light scattering properties originating from nanorods with length scales on the order of one micron. The films are sensitized with CdSe quantum dots (QDs) by successive ionic layer adsorption and reaction (SILAR) and integrated as a photoanode in quantum dot sensitized solar cells (QDSCs). Incorporating nanorods in photoanode structures provided 4- to 8-fold enhancement in light scattering, which leads to a high power conversion efficiency, 3.03% (Voc = 497 mV, Jsc = 11.32 mA/cm2, FF = 0.54), in optimized structures. High efficiency can be obtained... 

Herein, a solution-processed, bottom-up-fabricated, nanowire network electrode is developed. This electrode features a ZnO template which is converted into locally connected, infiltratable, TiO2 nanowires. This new electrode is used to build a depleted bulk heterojunction solar cell employing hybrid-passivated colloidal quantum dots. The new electrode allows the application of a thicker, and thus more light-absorbing, colloidal quantum dot active layer, from which charge extraction of an efficiency comparable to that obtained from a thinner, planar device could be obtained  

PbS nanoparticles were in situ deposited on graphene sheets by a successive ionic liquid adsorption and reaction method to prepare a graphene/PbS composite counter electrode for CdS/CdSe quantum dot sensitized solar cells (QDSCs). Under 1 sun illumination, the cells with graphene/PbS counter electrodes (CEs) show a maximum energy conversion efficiency of 2.63%, which is remarkably higher than that of those employing PbS (1.28%) or graphene (0.23%) CEs. Electrochemical impedance spectroscopy analysis shows that graphene/PbS composite counter electrodes have lower charge-transfer resistance at the interface of the CE and the polysulfide redox electrolyte, compared to those cells with PbS and... 

In this paper a new cell structure is introduced to reduce the rate of CdTe corrosion in quantum dot sensitized solar cells (QDSSCs) using I -/I- 3 electrolyte. In this cell, one electrode is a titania nanorod that was sensitized with CdTe quantum dots as the working electrode. A thin gold layer is sputtered on the electrode to act as a protective layer against the I-/I- 3 corrosive electrolyte and to passivate the CdTe surface traps which are the main recombination centres in a QDSSC. In addition, a Schottky barrier formed at the interface of Au and CdTe prevents direct electron recombination from the CdTe conduction band with I- 3 ions. The mechanism of charge transfer and quantum dot... 

In this paper, we introduce the sequential deposition method for enhancing the performance of nanocomposite counter electrodes (CEs) in quantum dot sensitized solar cells (QDSCs). Here, various CEs are made by the deposition of CuS, PbS, and CuS/PbS nanocomposite layers on an FTO (fluorine doped tin oxide) coated glass substrate by a simple successive ionic layer adsorption and reaction (SILAR) method. The result indicates that the efficiency of the cells with CuS/PbS CEs is enhanced by 2.65% compared with the bare CuS (0.99%) or PbS (1.47%) CEs. Also, no considerable improvement is observed for PbS/CuS CEs (1.09%), which indicates that the order of PbS and CuS deposition is critical for... 

We introduce a new third generation of solar cell structure which inserts different-sized quantum dots in the active region of a pin structure. Generating an intermediate band in the bandgap of the host material makes a good overlap with a part of solar spectrum. The effect of the recombination mechanisms on efficiency and currentvoltage characteristics of this intermediate band solar cell is calculated. We deduce that the increase in recombination lifetime of the excited carriers can improve the characteristics of this structure. This result can be a route which helps us to take the effect on solar cell characteristics into consideration  

Copper sulfide deposited ZnO nanorods (ZnO NRs/CuS) have been applied as a new counter electrode material with high electrocatalytic activity towards polysulfide electrolyte, which results in the formation of a highly efficient counter electrode for QDSSCs. It was observed from the current density-voltage (J-V) characteristics that the short-circuit current density (Jsc), power conversion efficiency (PCE), and fill factor (FF) were enhanced from 7.63 mA cm-2 to 14.48 mA cm-2, 1.59% to 4.18%, and 0.29 to 0.38, respectively, when a bare CuS counter electrode was changed to a ZnO NRs/CuS counter electrode. Electrochemical impedance spectroscopy (EIS), Tafel polarization and cyclic voltammetry... 

The solar to electric power conversion efficiency (PCE) of perovskite solar cells (PSCs) has recently reached 22.7%, exceeding that of competing thin film photovoltaics and the market leader polycrystalline silicon. Further augmentation of the PCE toward the Shockley-Queisser limit of 33.5% warrants suppression of radiationless carrier recombination by judicious engineering of the interface between the light harvesting perovskite and the charge carrier extraction layers. Here, we introduce a mesoscopic oxide double layer as electron selective contact consisting of a scaffold of TiO2 nanoparticles covered by a thin film of SnO2, either in amorphous (a-SnO2), crystalline (c-SnO2), or... 

PbS quantum dots (QDs) have been extensively studied for photovoltaic applications, thanks to their facile and low-cost fabrication processing and interesting physical properties such as size dependent and tunable band gap. However, the performance of PbS QD-based solar cells is highly sensitive to the humidity level in the ambient air, which is a serious obstacle toward its practical applications. Although it has been previously revealed that oxygen doping of the hole transporting layer can mitigate the cause of this issue, the suggested methods to recover the device performance are time-consuming and relatively costly. Here, we report a low-power oxygen plasma treatment as a rapid and... 

Among the various approaches, ZnS treatment is the most convenient method for reducing the charge recombination in quantum dot-sensitized solar cells (QDSSCs). Here an improved method of ZnS treatment is explained for efficiency enhancement in QDSSCs. To get to the goal of device performance improvement, it is essential to have a uniform deposited layer. We utilized Triton X-100 (TX-100) as a surfactant to the convenient aqueous precursors during ZnS deposition by successive ionic layer adsorption and reaction method. It helps to decrease in contact angle and increase in wettability of the aqueous precursor and results in a more uniform deposited layer. The effect of modified ZnS treatment... 

Colloidal quantum dot solar cells have recently attracted significant attention due to their low-processing cost and surging photovoltaic performance. In this paper, a novel, reproducible, and simple solution-based process based on supercritical fluid toluene is presented for in situ growth and deposition PbS nanocrystals with oleic-acid passivation. A lead precursor containing sulfur was mixed with oleic acid in toluene and processed in a supercritical fluid condition at different temperatures of 140, 270 and 330 °C for 20 min. The quantum dots were deposited on a fluorine-doped tin oxide glass substrate inside the supercritical reactor. Transmission electron microscopy, X-ray diffraction,... 

Recently, hybrid graphene–quantum dot systems have attracted increasing attention for the next-generation optoelectronic devices such as ultrafast photo-detectors and solar energy harvesting. In this paper, a novel, one-step, reproducible, and solution-processed method is introduced to prepare hybrid graphene–PbS colloids by employing supercritical ethanol. In the hybrid nanocomposite, PbS quantum dots (~3 nm) are decorated on the reduced graphene oxide (rGO) nanosheets (~1 nm thickness and less than 1 micron lengths). By employing X-ray photoelectron and Raman and infrared spectroscopy techniques, it is shown that the rGO nanosheets are bonded to PbS nanocrystals through carboxylic bonds....