Sharif Digital Repository

This research investigated the forced convection heat transfer by using the swirling impinging jets. This study focused on nozzles, which equipped with twisted tapes via a numerical approach. The computational domain created by utilizing the fully structured meshes, which had very high quality from the viewpoint of aspect ratio and skewness. The numerical simulations were performed at four different jet-to-plate distances (L/D) of 2, 4, 6 and 8, four Reynolds numbers of 4000, 8000, 12,000 and 16,000, and also four different twist ratios (y/w) of 3, 4, 5 and 6. The mesh-independent tests were conducted based upon the average Nusselt number. The obtained results revealed good agreement with... 

In this research the performance of a U-shaped pulsating heat pipe (PHP) was investigated using numerical methods. This heat pipe consists of two sections: The evaporator is set at the two ends of the pipe, and the middle part of the pipe comprises the condenser section. This heat pipe is a type of open looped pulsating heat pipe. The governing equations are derived analytically from the continuity, momentum, and energy equations and are solved implicitly. In this model, considering the liquid mesh, the rate of convection and boiling heat transfer in the U-shaped PHP, which has not been investigated as of yet, are examined. The effect of the evaporator temperature on the pulse amplitude and... 

Optimized and informed design of impinging jets can effectively enhance their rate of heat transfer. One practical pathway for such designing is to add nanoparticles to a background fluid. Here, we determine the effects of nanoparticle chemistry, their size, and their total volume fraction in water on the rate of heat transfer. We perform a comprehensive optimization using artificial neural network (ANN) and genetic algorithm (GA) to systematically study the enhanced heat transfer in nanofluids compared to pure water in obtaining a uniform cooling on a constantly heated surface in a turbulent flow. Our results indicate that increasing the size and concentration of nanoparticles enhances the... 

This paper investigates numerically the problem of unsteady magnetohydrodynamic nanofluid flow and heat transfer between parallel plates due to the normal motion of the porous upper plate. The governing equations are solved via the fourth-order Runge-Kutta method. Different kind of nanoparticles is examined. The effects of kind of nanoparticle, nanofluid volume fraction, expansion ratio, Hartmann number, Reynolds number on velocity and temperature profiles are considered. Also effect of different types of nanoparticles is examined. Results indicate that velocity decreases with increase of Hartmann number due to effect of Lorentz forces. Rate of heat transfer increase with increase of... 

The overall heat transfer coefficient (OHTC) of air in a double-pipe helical heat exchanger is studied and experimentally investigated. In order to increase the rate of heat transfer in the annulus section, a copper-wire fin is soldered on the outside area of the internal tube. The literature correlations’ results are presented against the experimental data by changing mass flow rate and temperature, and consequently changing the Reynolds number. Further, a new method is suggested to obtain the heat transfer coefficients of double-pipe helical heat exchangers for the internal tube and the annulus section by combining two of the previously proposed approaches and making subsequent... 

In this paper we report experimental results for the performance and rate of heat transfer in copper tubes in solar water heaters with thermosyphonic flow in continuation of experimental data reported in previous publications (Solar Energy, 2003, vol. 74, pp. 441-445, and Energy Sources, 1997, vol. 19, pp. 147-152). We also show a comparison between performances of three kinds of tubes: copper, polypropylene and steel under similar conditions. An analytical relation for calculation of rate of heat transfer in copper tubes is also presented in terms of Nusselt versus Reynolds and Prantdl numbers. A comparison of experimental data showed that performance of copper tubes is slightly better than... 

The aim of this work is to analyze the gas flow in high pressure buried pipelines subjected to wall friction and heat transfer. The governing equations for one-dimensional compressible pipe flow are derived and solved numerically. The effects of friction, heat transfer from the wall and inlet temperature on various parameters such as pressure, temperature, Mach number and mass flow rate of the gas are investigated. The numerical scheme and numerical solution was confirmed by some previous numerical studies and available experimental data. The results show that the rate of heat transfer has not a considerable effect on inflow Mach number, but it can reduce the choking length in larger f DL/D... 

The application of heat pipes with flat evaporators in cooling electronic devices has attracted a lot of attention in recent years. Increasing the rate of heat transfer in their evaporator by utilizing structured surfaces is considered as a prominent method for reducing the thermal resistance of the heat pipes. In this study, the performance of a thermosyphon heat pipe with novel radially rectangular-grooved and radially inclined triangular-grooved evaporator surfaces was evaluated experimentally. It is hypothesized that the radial grooves may enhance the performance by inducing rotational motions and increasing the heat transfer coefficients. Based on the results, the optimum filling ratio...