Sharif Digital Repository

In this thesis the instability regimes of the liquid sheet resulted from interactions of three converging jets is investigated. To this end, the shadowgraphy method is used. All the experiments have been done under the atmospheric pressure by using water as the jet fluid. The injectors are orifice ones.In our study, the effects of changing the jet velocities and changing the three jets’ structure (planar and non-planar) in having different liquid sheet shapes are investigated.Although so many researches have been done on interactions of two converging jets until now, there is almost not any researches about interactions of three converging jets. Considering this, this thesis topic is novel,... 

In the present research, a test stand for investigating the behavior of an injected jet in cross flow, is established. In All experiments water and air was used as injected jet and cross flow respectively. At the beginning, with help of dimensional analysis, non-dimensional parameters are introduced and their effect of these parameter on the jet behavior, as the most important goal of this research, is investigated. In order to inject the fluid in the cross flow, two injector with 0.58 mm and 1.08 mm exit diameter and 10 mm exit length was used, and jet speed varies from 2 m/s to 12 m/s. The cross section of the wind tunnel was a 8cm-edge-square and the air speed was adjustable in the range... 

Injection of liquid fuel in the cross-flowing air provides a means of higher penetration, rapid mixing of liquid fuel and air, and is encountered in many engineering applications. Air-breathing propulsion systems (e.g. gas turbine combustors, ramjets, and scramjets), liquid rocket engines,cooling sprays for turbine blades, and injection of fuel in the afterburners are examples of such applications. The identification of microscopic characteristics is one of the basic methods of atomizer examination, which has not been taken into account due to inadequate experimental equipment. In the present study, droplet mono-frame velocimetry and size distribution of secondary atomization in a pressure... 

The velocity of the hot outflow gas in laminar premixed flame is one of the important properties of combustion, along with other properties such as temperature and flame components. In fact, laminar flame velocity has been employed in a multitude number of concepts ranging from engine design to achieving flame properties under turbulent conditions. In this research, a cylindrical Bunsen burner and appropriate TIO2 particles were used. Particles with diameters between 10-23 microns were used and the exit diameter of burner considered 14 mm. In this study, the equivalence ratio with a value between 0.9-1.2 are fed with LPG fuel to create a laminar premixed flame. As a result of the present... 

In This Study break up and trajectory of aerated liquid jet in subsonic cross flow has been investigated. An effervescent two phase flow injector has been used with two different diameters for its external orifice. The effects of non-dimensional parameters on the trajectory of aerated liquid jet were evaluated. Water was used as the fluid for the purpose of producing liquid jet. Air was used to produce gaseous phase in the injector and the cross flow as well.
A duct with a square cross section and a blower in the inlet of the duct were used to produce the cross flow. Mixture of air and water was injected into the cross flow by the injector installed at the bottom of the duct. Shadowgraph... 

Electrospray is one of the liquid spraying methods. This study has an insight on Electrospray phenomenon and its effective parameters. First, there is a short introduction of phenomenon, then, how it works and effective factors related to the procedure are described. All modes, the forces and the situation to establish has been investigated for ethanol sprayed from hemispherical nozzle. Suitable configuration is introduced and for different flow rates and voltages the phenomenon is studied. One of the innovations of this study is the imaging technique used to captured high-quality images. In fact, captured images by means of high-power light-emitting diode (LED) synchronized with digital... 

This research investigates the break-up physics and spray characteristics of flow-blurring spray by implementing machine learning on numerical and experimental datasets. To do so, five crucial parameters of atomization, including SMD, axial and radial velocity components, penetration length, break-up length, and spray angle, are selected to be studied. Firstly, size and velocity distribution datasets are gathered using available experimental papers. Prior to modeling by Multi-Layer Perceptron neural networks, the datasets were pre-processed in terms of the existence of multi-value and outlier instances. Secondly, the physics of mixing flow inside the injection system was numerically...