Sharif Digital Repository

We have studied the effect of sintering temperature on the weak link behavior of polycrystalline Bi2223 superconductors with different intergranular coupling using the XRD, electrical resistivity and AC susceptibility techniques. The XRD results show that by increasing sintering temperature up to 865°C the Bi2212 phase fraction decrease. It was found that the Bi2212 phase on the grain boundaries is likely to play the role of weak links and consequently reduces the intergranular critical current densities. © 2006 WILEY-VCH Verlag GmbH & Co. KGaA  

In this paper, an investigation of bi-material parts produced by a two-component metal injection moulding process is presented. The compatibility of different materials for this process was evaluated by sinter dilatometry, taking into account the effects of powder particle size, powder loading and use of master alloys on the sintering behaviour. In a second step, sample material joints of 316L / H13, 316L / 17-4PH and 316L / iron were moulded, debinded and sintered together. The interfaces obtained were examined by optical microscopy and SEM. The diffusion of alloying elements across the interfaces was shown as a function of sintering temperatures. Changes in microstructures and chemical... 

In this study Al2O3-SiC micro/nanocomposites have been fabricated by mixing alumina nanopowders and silicon carbide micro/nanopowders, followed by hot pressing at 1550, 1600, 1650 and 1700°C. The density, mechanical properties and fracture mode of Al2O3-SiC composites containing different volume fractions (2.5%, 5%, 7.5%, 10% and 15%) of micro/nanoscale SiC particles were investigated and compared with those of alumina. The relative density of composites could reach values very close to theoretical density, especially after sintering at 1700°C. However, relative density declined by increasing the SiC fraction at the same sintering temperature. The flexural strength of composites was best for... 

In this research, effects of two-step sintering parameters, such as first and second step sintering temperatures (T1 and T2, respectively) and soaking time in the second step, on microstructure and electrical properties of ZnO varistors have been studied. In addition, slow rate of grain growth in the second step of sintering has also been investigated. Near fully dense (higher than 99%) and sub-micron grain size (1-0.75 μm) ZnO varistors have been fabricated by different two-step sintering cycles. Decreasing T1 and T2 result in longer necessary time in the second step to reach near full density with smaller final grain size. The superior electrical properties of varistors (VB: 2050-1022 V/mm... 

10Ce-TZP/Al2O3 nanoparticles as reinforcement can be a good substitute in aluminum matrix composites prepared through powder metallurgy. In this work, the effects of sintering temperature on the hardness, friction, and wear characteristics of Al-10Ce-TZP/Al2O3 composites have been investigated. Ce-TZP/Al2O3 nanocomposites were synthesized by the aqueous combustion method. About 7 wt% 10Ce-TZP/Al2O3-aluminum composites in the form of cylindrical samples were prepared at the sintering temperatures of 400°C, 450°C, and 500°C under an applied pressure of 600 MPa for 60 min. The experimental results show that the distribution of Ce-TZP/Al2O3 nanocomposite into the metal matrix is homogenous and... 

In this study, SnO 2-based varistors were prepared from mechanically activated nanocrystalline powders. Nanocrystalline powders were derived by subjecting the initial powders to intensive high-energy activation with different times and ball to powder ratio. The effect of activation parameters on the powder properties and sintering temperature, as well as microstructural, micro-electrical and macro-electrical properties of the final specimens was evaluated. Varistors derived from high-energy mechanical activation exhibit a higher density (98.3% relative density) and more refined microstructure upon sintering at 1,300 °C in comparison varistors prepared from conventional powders. Breakdown... 

Sintering process at temperature intervals close to the melting point of polymers is greatly important due to its role in synthesizing porous materials. During sintering, particles of polymeric materials coalesce throughout a process called interdiffusion. On the contrary, crystallization strongly affects the interdiffusion process at temperature intervals below and close to the melting point. Apparently, the outcome of the contention between these two factors would determine the interfacial width. Therefore, the current study presents a model, which takes both crystallization and interdiffusion into account, to predict sintering kinetic. Consequently, interfacial strength was assessed with... 

In this research, full density, single phase microstructure (in the XRD and SEM detection limits), and fine-grained SnO2 varistors with an average grain size of 0.65 μm was acquired at low temperature by the two-step sintering technique. The sintering temperature was successfully decreased from 1300 °C in the normal sintering to 1150 °C and 1100 °C of respectively the first and the second stage in the two-step sintering. The mechanism of grain growth suppression of the two-step sintered samples was discussed and it was suggested that in addition to triple point junction, solute drag and/or nano-secondary phases contribute to cease the grain growth. These SnO2 varistors exhibited ultra-high... 

Manufacturing of complex-shaped bimetals utilizing two-color powder injection molding (2C-PIM) and three-dimensional printing (3DP) processes, which basically involve sintering of a powder/binder mixture, has been attracted a great interest. This article addresses sintering of biocompatible Co-Cr-Mo alloy for manufacturing stepwise porosity-graded composite structures. Such composite structures provide strength at the core and a porous layer for the tissue growth. To evaluate the process, two grades of gas atomized Co-Cr-Mo powder with an average particle size of 19 and 63 μm were used. Isothermal and nonisothermal sintering behavior of the loose powders under hydrogen and argon atmospheres... 

Titanium carbonated hydroxyapatite (Ti/CHA) nanobiocomposites have extensive biological applications due to the excellent biocompatibility and similar characteristics to the human bone. Ti/CHA nanobiocomposite has good biological properties but it suffer from diverse characteristics especially in hardness, Young's modulus, apparent porosity and relative density. This investigation is an attempt to propose the predictive models using gene expression programming (GEP) to estimate these characteristics. In this regards, GEP is used to model and compare the effect of practical variables including pressure, Ti/CHA contents and sintering temperature on their monitored properties. To achieve this... 

In this paper, the rapid synthesis of nanostructured NiTi–Ni3Ti intermetallic alloy from titanium and nickel powders through mechanical alloying followed by microwave-assisted sintering process was investigated. The sintered samples at different temperatures exhibited major phases of NiTi– B2 and Ni3Ti, and minor phases of NiTi–B19′ and Ti2Ni. The density, porosity and microhardness of the sample varied based on the sintering temperature, in which the highest density and microhardness (~750 H V) were obtained at sintering temperature of 1100 °C. Based on the results of this research, the microwave-assisted sintering can be applied to fabricate Ni–Ti alloys with improved mechanical properties... 

In this paper, the rapid synthesis of nanostructured NiTi–Ni3Ti intermetallic alloy from titanium and nickel powders through mechanical alloying followed by microwave-assisted sintering process was investigated. The sintered samples at different temperatures exhibited major phases of NiTi– B2 and Ni3Ti, and minor phases of NiTi–B19′ and Ti2Ni. The density, porosity and microhardness of the sample varied based on the sintering temperature, in which the highest density and microhardness (~750 H V) were obtained at sintering temperature of 1100 °C. Based on the results of this research, the microwave-assisted sintering can be applied to fabricate Ni–Ti alloys with improved mechanical properties... 

Three-dimensional macroporous fluorine-doped tin oxide (p-FTO) films were successfully deposited using commercial ink of FTO powder and SnCl2 salt via Dr. Blade method. Various features of p-FTO thin films were studied as a function of the ink composition and sintering temperature. The morphological studies corroborated formation of porous, uniform, and crack-free FTO films after annealing at 300 °C for 10 min in air. X-ray diffraction pattern demonstrated development of highly crystalline FTO films. The lowest sheet resistance of 47 Ω/□ was obtained for the p-FTO film with a thickness of 21 μm. The capacitance of thin p-FTO films was investigated using a three-electrode system and the... 

Nanocrystalline zinc titanate (ZnTiO3) thin films and powders with purity of 94% were produced at the low sintering temperature of 500 °C and the short sintering time of 1 h by a straightforward aqueous particulate sol-gel route. The effect of Zn:Ti molar ratio was studied on the crystallisation behaviour of zinc titanates. The prepared sols showed a narrow particle size distribution in the range 17-19 nm. X-ray diffraction (XRD) and Fourier transform infrared spectroscopy (FTIR) revealed that the powders contained mixtures of the rhombohedral-ZnTiO3, cubic-ZnO, cubic-Zn2TiO4 phases, as well as the anatase-TiO2 and the rutile-TiO2 depending on the sintering temperature and Zn:Ti molar ratio.... 

In this work the effects of sintering temperature on the hardness, friction and wear characteristics of Al-10Ce-TZP/Al2O3 composites have been investigated. Aluminum and Ce-TZP/Al2O3 nanocomposite were selected as raw materials. Ce-TZP/Al2O3 nanocomposites were synthesized by the aqueous combustion method. 7 wt. % 10Ce-TZP/Al2O3 composites in the form of cylindrical samples were prepared at the sintering temperatures of 400, 450 and 500°C under an applied pressure of 600 MPa for 60 min. Wear tests were carried out using the pin-on-disk method under normal loads of 10 and 20 Kgf at constant sliding velocity of 0.25 m/s. The surfaces of the worn nanocomposite were examined by scanning electron... 

The BaCe0.9Y0.1O3-δ (BCY) perovskite membrane was successfully synthesized by liquid citrate method. The phase structure of the powder was characterized by X-ray diffraction (XRD). Scanning electron microscopy (SEM) was used to characterize microstructures of the membrane sintered under various conditions. Sintering temperatures and dwell time during sintering influence the final microstructure of the ceramic. Results showed that increasing sintering temperature resulted in a dense membrane with clear grains. An increase of dwell time was favorable to produce membranes with larger grains in the sintered ceramics. A density of 5.87 g/cm3 was reached for the membrane after sintering at 1200 °C... 

A zirconia/alumina nanocomposite stabilized with cerium oxide (Ce-TZP/Al2O3 nanocomposite) can be a good substitute as reinforcement in metal matrix composites. In the present study, the effect of the amount of 10Ce-TZP/Al2O3 particles on the microstructure and properties of Al/(10Ce-TZP/Al2O3) nanocomposites was investigated. For this purpose, aluminum powders with average size of 30μm were ball-milled with 10Ce-TZP/Al2O3 nanocomposite powders (synthesized by aqueous combustion) in varying amounts of 1, 3, 5, 7, and 10wt.%. Cylindrical-shape samples were prepared by pressing the powders at 600MPa for 60min while heating at 400-450°C. The specimens were then characterized by scanning and... 

In this study, TiO 2-SiO 2 nanocomposite films with different amounts of SiO 2 were prepared by sol-gel process and were coated onto stainless steel 316L. The effect of addition of various amount of SiO 2 in the precursor solution on the photocatalysis, photo-generated hydrophilicity and self-cleaning property of TiO 2 thin films was investigated by X-ray diffraction, Fourier transform infrared spectroscopy, water contact angle measurements and UV spectroscopy. In the tested ranges of SiO 2 content and sintering temperature, the highest photocatalytic activity and self-cleaning property were observed in the 15 mol% SiO 2 sample sintered at 750 °C. Addition of less than 30 mol% SiO 2 had a... 

In this study, Porous NiTi shape memory alloy has been produced by mechanical alloying of the elemental Ni and Ti powders. The compacting process was done at two temperatures (warm and cold press) and then sintering at 980 and 1050°C was performed on the specimens. Microstructure and mechanical prop-erties of the samples were investigated by optical microscopy, scanning electron microscopy (SEM) and X-ray diffraction. Moreover, shear punch test (SPT) employed to investigate the effect of compaction pressure and sintering temperature on the mechanical properties of the fabricated samples. It was revealed that warm compaction/sintering resulted in 15% yield stress improvement and 20% ultimate... 

The properties of W-15 wt.%Cu composites were investigated by preparing two distinct composites of micrometer and nanoscale structures. Micrometer composite was produced by mixing elemental W and Cu powders and nanometer one was synthesized through a mechanochemical reaction between WO3 and CuO powders. Subsequent compaction and sintering process was performed to ensure maximum possible densification at 1000-1200 °C temperatures. Finally, the behavior of produced samples including relative density, hardness, compressive strength, electrical conductivity, coefficient of thermal expansion (CTE) and room temperature corrosion resistance were examined. Among the composites, nano-structured...