Sharif Digital Repository

Li2FeSiO4 was synthesized through Sol–Gel method and the effect of calcination temperature, time and chelating agent concentration were investigated. Appropriate calcination temperature above 550 °C was determined by TG/DTA analysis. Afterward, the dried gel powder was calcined at each temperature of 650 °C, 700 °C and 750 °C for 1, 2 and 3 h. XRD studies illustrated the most appropriate calcination temperature of 700 °C for 1 h. To compare the effect of chelating agent concentration, citric acid with molar ratio of 1/3, 2/3 and 1 were used which 1/3 was determined as the best concentration. FE-SEM observation showed that mean grain is size lower than 100 nm. By using this material, a three... 

Stabilised titania sols were prepared using an additive free particulate sol-gel route, via electrostatic stabilisation mechanism, with various processing parameters. Peptisation temperature, 50°C and 70°C, and TiO2 concentration, 0.1, 0.2 and 0.4 molar, were chosen as processing parameters during sol preparation. Results from TiO2 particle size and zeta potential of sols revealed that the smallest titania hydrodynamic diameter (13 nm) and the highest zeta potential (47.7 mV) were obtained for the sol produced at the lower peptisation temperature of 50°C and lower TiO 2 concentration of 0.1 M. On the other hand, between the sols prepared at 70°C, smaller titania particles (20 nm) and higher... 

In this paper, the combination of dry reforming and partial oxidation of methane on nickel catalysts supported on mesoporous MgAl2O4 was investigated. The support was prepared by a facile sol-gel route using propylene oxide as a gelation agent. The characterizations of the catalysts were performed by BET, XRD, TPR, TPO, TPH, UV–vis, CO-dispersion, SEM and TEM techniques. In addition, the effects of nickel content, reaction and reduction temperatures, feed ratio and the GHSV value on the physicochemical and catalytic properties were studied. The results revealed that the nickel content had an optimum value of 7.5 wt% and the catalyst with this content of nickel exhibited the highest activity.... 

In present research six samples of nano X-type hexagonal ferrites with general formula SrBaMg2-xCoxDyyFe28-yO46 (x = 0–1; y = 0–0.1 with step size of 0.2 and 0.02, respectively) were synthesized by sol–gel technique. The temperature required for the phase formation of these materials was estimated using thermogravimetric analysis. X-ray diffraction patterns revealed the pure phase of the prepared materials up to the doping concentration of x = 0.4, y = 0.04 along with the second phase for higher doping concentration. The secondary phase appeared due to the solubility limit of higher ionic radius Dy3+ ions into the hexagonal lattice. The mean crystalline size decreased from 29 to 18 nm while... 

High performance Fe-Gd-P tri-doped TiO2 nanoparticles (1 at% for each dopant) were successfully synthesized by a modified sol–gel method. Various analytical and spectroscopic techniques were carried out to determine the physicochemical properties of the prepared samples, including XRD, EDX, FESEM, BET, FTIR, XPS, PL, EIS and UV–Vis diffuse reflectance spectroscopy. The photocatalytic activities of prepared samples were evaluated by photo degradation of methyl orange (MO) and 4-chlorophenol (4-CP) as model pollutants under visible light irradiation. Effects of each dopant on different properties of TiO2 nanoparticles were investigated. Results show that Gd and P doping enhances TiO2 surface... 

Carbon nanotubes with unique physical and mechanical properties have shown great potential for biological applications, including tissue engineering and mimicking the structure and properties of human bones. In the present work, sol-gel synthesized nanocomposite powder of multi-wall carbon nanotube/hydroxyapatite characterized using field-emission scanning electron microscopy, transmission electron microscope, X-ray diffraction, Fourier transform infra-red spectroscopy and thermal analyses. The results show homogenous dispersion of nanotube in well-crystallized hydroxyapatite ceramic matrix. Scanning electron microscopy and transmission electron microscope observations show the sodium... 

The thermal decomposition of Aluminum Titanate in exposure to pure Aluminum was examined both in powder and in bulk form. Optical microscopy, FE-SEM, XRD, DSC and TGA examinations were conducted to take the possible chemical reactions between Aluminum Titanate and Al into consideration. It was found that as Aluminum Titanate particles are exposed to Al matrix, the thermal stability of Aluminum Titanate is degraded and its decomposition temperature is reduced from 850°C to 550°C. Also, the chemical reactions between Aluminum Titanate and Al start along the interfaces, and the reaction products, i.e. Al3Ti, Al2O3, TiO2 and O2 gas are left there. A mechanism was suggested to describe the... 

An attempt to synthesize pyrochlore free (x)PMN-(1 - x)PZT ceramics (where x is 0, 0.1, 0.3, 0.5, 0.7, 0.9, and 1) by a mixed powder method was made. In this work, a sol-gel prepared PZT powder was mixed with the mixture of milled PbO, MgO and Nb2O5, and sintered in a two step sintering process. The produced samples with high PZT content showed low densities due to the low compaction ratio of PZT powder. The dielectric properties of PZT-rich and PMN-rich materials were high (with dielectric constant of about 19,000 and 33,000 for PZT-rich and PMN-rich ceramics, respectively) while the other samples exhibited low dielectric properties. Also, the effect of combining PMN with PZT on Curie... 

In this paper, a comprehensive study was conducted on the application of various MeAl2O4 spinels (Me = Fe, Co, Ni, Cu, Zn, Mg) as the catalyst support for the preparation of nickel-based catalysts in the combined dry reforming and partial oxidation. These supports were synthesized by a novel facile sol-gel method using propylene oxide as the gelation agent and nickel was deposited on these supports by the deposition-precipitation method. The prepared samples were characterized by N2 adsorption/desorption, XRD, TPR, TPO, CO2-TPD, SEM, and TEM techniques. In addition, the temperature-programmed methane dissociation (TPMD) was performed to evaluate the effect of nickel-support interaction on... 

In this experimental study, a kinetic model has been developed for Fischer-Tropsch synthesis reactions by using sol-gel technique and Fe/Ni/Al 2O 3 as the catalyst (40% Fe/60% Ni/40 wt.%Al 2O 3) in a differential fixed-bed micro reactor assuming no internal or external diffusion. Operating conditions of the reactor were as follows: total pressure 1-12 atm; Temperature 220-260 °C; H 2/CO feed ratio 1.5-2; gas hourly space velocity 2100-7000 cm 3(STP)/h/ g cat and conversions of 6-37% of hydrogen and 7-21% of carbon monoxide. Mass transfer limitations were investigated by changing synthesis gas velocity in reactors which differ in size. Based on the hypothesis that water inhibits the intrinsic... 

A nanocomposite of Ce-doped TiO2-reduced graphene oxide (CedT/RGO) was synthesized to evaluate the synergistic effects of constituents on electrical and photoelectric properties. The nanoparticles of titania and CedT were synthesized via the sol-gel method. Then, RGO was prepared using a new version derived from the Hammer's method and hydrothermal methods. Finally, CedT/RGO nanocomposite was synthesized applying hydrothermal method. The nanoparticles and nanocomposite were characterized by X-ray diffraction, Fourier transform infrared spectroscopy, Field emission scanning electron microscopy (FESEM), Energy dispersive X-ray spectroscopy and elemental mapping. Then, diffuse reflectance and... 

A facile sol-gel synthesis for self-agglomeration of metallic silver nanoparticles, with fcc crystalline structure, on the silica surface in a low annealing temperature has been introduced. X-ray photoelectron spectroscopy (XPS) revealed initial agglomeration (∼30 times greater than the nominal concentration of Ag) of the nanoparticles on the surface of the dried film (100 °C) and also their oxidation as well as easy diffusion (with 0.08 eV required activation energy) into the porous silica thin films, by increasing the annealing temperature (200-400 °C). By raising the Ag concentration from 0.2 to 1.6 mol% in the sol, the average size of the Ag nanoparticles increased from ∼5 to 37 nm... 

To evaluate the selectivity and efficiency of solid phase microextraction (SPME) fiber coatings, synthesized by sol-gel technology, roles of precursors and coating polymers were extensively investigated. An on-line combination of capillary microextraction (CME) technique and high performance liquid chromatography (HPLC) was set up to perform the investigation. Ten different fiber coatings were synthesized in which five of them contained only the precursor and the rests were prepared using both the precursor and coating polymer. All the coatings were chemically bonded to the inner surface of copper tubes, intended to be used as the CME device and already functionalized by self-assembly... 

A method based on solid-phase microextraction (SPME) followed by on-fiber derivatization and gas chromatography-mass spectrometry detection (GC-MS) for determination of phenol in air was developed. Three different types of SPME fibers, polar and non-polar poly(dimethylsiloxane) (PDMS) and polyethylene glycol (PEG) were synthesized using sol-gel technology and their feasibility to the sampling of phenol were investigated. Different derivatization reagents for post on-fiber derivatization of phenol were studied. Important parameters influencing the extraction and derivatization process such as type of fiber coating, type and volume of derivatizing reagent, derivatization time and temperature,... 

In this survey, a reliable and applicable Y–Y shaped micro–channel in a microfluidic device was designed and manufactured. A number of micro–scaled hedges were precisely fabricated inside the micro–channel to facilitate the immobilization of synthesized core–shell Fe3O4@SiO2 magnetic nanoparticles (MNPs), functionalized by triethoxyphenylsilane (TEPS) by sol-gel technique. Both sample and reagents were introduced into the microfluidic device by a syringe pump to perform the extraction and desorption steps. The functionalized MNPs were characterized by transmission electron microscopy, X-ray diffraction spectroscopy and Fourier transform infrared spectroscopy. By adopting the strategy of...