Sharif Digital Repository

The influence of solution treatment on precipitation behavior of AEREX™350 was investigated using hardness testing, TEM and SEM. Samples were solution treated at 1050°C and 1075°C for 1 hr and then aged at 700°C, 750°C and 800°C for 1,2,4,8 and 25 hrs. It was found that different solution treatment may be used for different applications of AEREX™350  

The present study investigates the evolution of γ′ precipitate microstructure in a creep damaged IN738LC superalloy during different stages of rejuvenation heat treatment cycles. Dissolution of coarsened γ′ precipitates in the creep damaged alloy occurred during different solution treatments. The precipitates that did not dissolve completely during solution treatment and those formed during subsequent cooling were considered to be as remnant and cooling precipitates respectively. It was found that higher solution treatment temperatures result in lower volume fraction of remnant precipitates and further formation of cooling precipitates. Slower cooling rates after solution treatment gave the... 

The age-hardening behavior and microstructure of selected samples of a Ni-Co alloy were studied using hardness testing, optical microscopy, and scanning and transmission electron microscopy. The final microstructure of the material was found to be sensitive to the temperature of the solution treatment. This approach may be used to optimize the microstructure of the alloy for different applications. © 2007 Acta Materialia Inc  

The effects of initial heat treatments, i.e. solution treating and over ageing, on deformation behavior of an age hardenable Al-Cu-Mg alloy, including mechanical properties and texture evolution, during multi-directional forging (MDF) are investigated. Hardness measurements, electron back scatter diffraction (EBSD) maps, and differential scanning calorimetry (DSC) are carried out. Mechanical behaviors of the alloy in terms of compressive stress and hardness test after MDF are investigated. In both solution treated and over-aged alloys, the compressive stress during MDF shows an increase up to the second pass, and by further straining the flow stress is decreased. However, shear and... 

In this research, the effect of applying severe strain before solid solution treatment (SST) for AA2024-O was studied. Providing concurrent insights into solutionizing behavior and microstructural evolution corresponding to hardness is important. Multi-directional forging (MDF) was used as a severe plastic deformation (SPD) method. After applying SST on MDFed (4 passes) and as-annealed samples, natural aging (NA) was used as the following treatment to examine the role of severe strain on the solutionizing behavior. In most previous attempts, SPD has been used after SST, but one of the innovations of the present work is the study of SPD before SST. Experimental results show that adding a... 

This research study aims at investigating the influence of partial solution treatment and the subsequent cooling strategy on the microstructure and mechanical properties of an as-cast Co–Cr–W superalloy. Three different cooling scenarios were employed to explore the effect of cooling rate on the carbide reprecipitation potential from the solid solution formed during the heat treatment. The partial dissolution/breakdown of the continuous network of the Cr-rich M7C3 carbides during the partial solution treatment cycle along with their transformation to M23C6 carbides and formation of secondary carbides during the cooling stage were taken into account to discuss the obtained hardness values,... 

In this work, deformation behavior as well as creep and cavitation of AA7075-T76 were studied. The as-received plate was first stabilized utilizing solution treatment followed by two-stage artificial aging at 120 and 180 °C. Then, tensile tests were carried out on the aged-alloy in the temperature range between 120 and 250 °C under strain rates of 0.0005 and 0.005 s−1. Furthermore, stress-controlled creep tests were performed at temperatures varying between 120 and 210 °C at stresses ranging from 130 to 250 MPa. Microstructural evolution was then conducted to assess the microstructural changes and growth of cavities during creep employing optical metallography and scanning electron... 

In this study, the kinetics of aging in AA6061 and AA6061 with 5% volume fraction SiCp were studied and compared. The composite was first produced and homogenized using stir casting technique followed by hot extrusion with the ratio of 18:1. Then, both AA6061 and the composite were aged at three different temperatures including room temperature, 170 °C and 240 °C, while mechanical properties during aging were evaluated employing hardness measurements and tensile testing. Moreover, in order to assess the effect of plastic deformation on the kinetics of aging, a series of samples were first deformed by equal-channel angular pressing immediately after solution treatment and then aged in the... 

IN738LC is one of the superior nickel base superalloys utilized at high temperatures in aggressive environments. However, experiencing high temperatures and stresses during service causes microstructure deterioration and degradation of mechanical properties in this alloy. To restore the microstructure and mechanical properties of the degraded alloy, rejuvenation heat treatments can be considered. In this study, the evolution of microstructural features in a creep damaged IN738LC superalloy during different stages of rejuvenation heat treatment cycles was investigated. During solution treatment stage, dissolution of coarsened γ′ precipitates, grain boundary films and transition zone around... 

In the present research the aging behavior of Al6061 alloy and Al6061/SiCp composite fabricated by powder metallurgy method was investigated. The solution treatment of the samples were carried out at 527°C for 2, 3and 4 h followed by aging at 180°C for different aging times between 1 and 10 h. The existence of SiC particles led to increasing the peak hardness of the composite. The peak hardness of the composite took place at shorter times than that of the 6061 alloy for the samples solution treated for 3and 4 h, but took place at longer times for the samples solution treated for 2 h. The optimum solution treating time was about 3 h for both the composite and the 6061 alloy that led to the... 

In the present research work the 2024 aluminum alloy was reinforced with SiC particles via powder metallurgy method. The effect of heat treatment conditions on artificial aging kinetics was investigated. The solution treatment of the composite sample and the unreinforced alloy was carried out at 495 °C for 1, 2 and 3 h followed by aging at 191 °C for various aging times between 1 and 10 h. The existence of SiC particles led to increasing the peak hardness of the alloy. The peak hardness of the composite sample took place at shorter times than that of the unreinforced alloy for the samples solution treated for 2 and 3 h, but took place at longer times for the samples solution treated for 1 h.... 

In order to optimize the aging treatment of Mg-1.8Zn-0.7Si-0.4Ca alloy, different times and temperatures of solid solution and age hardening were applied to the alloy specimens. Microstructures and mechanical properties of the specimens were investigated using the optical microscopy, field emission scanning electron microscopy equipped with an energy dispersive x-ray spectrometer, x-ray diffraction, hardness, and shear punch tests. The lowest hardness and strength were achieved by solution treating of the alloy at 500 °C for 8 h, presenting the optimal condition for solution treatment of the alloy. The microstructural examinations revealed three different precipitates consisting of CaMgSi,... 

The effects of zinc content (2 and 4 wt%), heat treatment (solution-Treated and T6), as well as hot deformation (extrusion and multi-directional forging (MDF)) on the microstructure, mechanical and degradation behavior of Mg-Zn alloys were studied. As the result of microstructure refinement, solid solution and precipitate strengthening (formation of MgZn second phases), the strength of pure Mg was increased after Zn addition. Solution treatment of the Mg-4Zn alloy resulted in 16% softening due to the dissolution of the MgZn second phases and also grain growth, while aging treatment increased the strength value by 8% in comparison to the as-cast material because of the formation of the fine... 

The current study investigated the effect of heat treatment parameters, including solution treatment temperature (STT), time, and quench rate, on the microstructure, defects, and hardness of an Al-16Si-6Cu Shift fork die-cast alloy. The changes in primary silicon particle (PSP) features were examined quantitatively by optical microscopy, coupled with image analysis and SEM equipped with EDS. The biggest PSPs (27 ± 8 µm) and the highest area fraction (23%) were found in the sample solution treated at 470°C and cooled in the furnace. The hardness value increased in heat-treated samples slightly (140–148 BHN). A lower STT (420°C) and a lower ageing time (1 h) are suitable conditions for the...