Sharif Digital Repository

CdS nanocrystals were thermochemically (thermally activated) synthesized thorough the reaction between CdSO4 and Na2S 2O3 in an aqueous solution. Thioglycolic Acid (TGA) was used as the capping agent and catalyst of the reaction. The method was based on heat activated dissociation of Na2S2O3 and controllable release of S and free electrons in the solution. CdS NCs were formed by heating the sample solution at 96 C for 1 h. The results of optical spectroscopy and transmission electron microscopy demonstrated round shape NCs with sizes about 3.0 nm. The nanocrystals were also luminescent and represented a broad emission with a peak located at 515 nm and FWHM of 160 nm. Several samples were... 

Graphene oxide foam (GOF) layers with thicknesses of ∼15-50 μm and density of ∼10 graphene oxide (GO) sheets/μm were fabricated by precipitation of chemically exfoliated GO sheets in an aqueous suspension at ∼80 °C under UV irradiation. Then, rolled GOFs with desirable scales were developed as electrically conductive 3D-scaffolds and applied in directional growth of neural fibers, through differentiation of human neural stem cells (hNSCs) into neurons under an electrical stimulation. X-ray photoelectron spectroscopy indicated that the UV irradiation resulted in partial deoxygenation of the layers. Scanning electron microscopy and Raman spectroscopy confirmed the presence of multilayer GO... 

In this investigation, sol-gel synthesized nanoporous silica thin films, annealed at different temperatures, with long time superhydrophilic property have been studied. Two kinds of sol-gel silica thin films were fabricated by dip-coating of glass substrates in two different solutions; with low and high water. The transparent coated films were dried at 100 °C and then annealed in a temperature range of 200-500 °C. The average water contact angle of the silica films prepared with low water content and annealed at 300 °C measured about 5° for a long time (6 months) without any UV irradiation. Instead, adding water into the sol resulted in silica films with an average water contact angle... 

In this research, initially anodization process was used to fabricate ZnO nanorods on Zn substrate and then RF sputtering technique was applied to grow a thin layer of polytetrafluoroethylene (PTFE, Teflon) on the coated ZnO nanorods for producing a superhydrophobic surface. According to scanning electron microscopy (SEM) observations, ZnO nanorods were formed with average diameter and length of about ∼180 nm and 14 μm, respectively. Superhydrophilic property of ZnO nanorods and superhydrophobic property of PTFE/ZnO nanorods was investigated by water contact angle (WCA) measurements. It was found that the contact angle varied with the PTFE deposition time. The highest contact angle... 

The separation of water-oil mixtures has attracted widespread attention because of the increasing amounts of oily wastewater produced from the daily activities of humans and different industrial processes. Therefore, the development of facile and efficient oil-water separation technologies is imperative. In this work, a new highly superhydrophilic-superoleophobic coated stainless steel mesh was fabricated using virtue of the surface modification of poly (BzVimBr-Vim)@PFOA@SiO2 nanoparticles (NPs) through a facile preparation process. The new fabricated superhydrophilic and highly oleophobic coating exhibits good adhesive properties. The oil contact angle (OCA) and water contact angle (WCA)... 

Liquid–liquid two-phase flow in microchannels is capable of boosting the heat removal rate in cooling processes. Formation of different two-phase flow patterns which affect the heat transfer rate is numerically investigated here in a T-junction containing water-oil flow. For this purpose, the finite element method (FEM)is applied to solve the unsteady two-phase Navier–Stokes equations along with the level set (LS)equation in order to capture the interface between phases. It is shown that the two-phase flow pattern in microchannels depends on the flow initial condition which causes hysteresis effect in two-phase flow. In this study, the hysteresis is observed in flow pattern and consequently... 

Electrospun porous membrane; Superhydrophilic surfaces; Superhydrophobic surfaces; Cell culture; Organ on a chip; Flexible membrane; Strong membrane; Surface modications  

onstructing of the scaffolds for cell culture applications has long been of interest for engineering researchers and biologist. In this study, a novel process is utilized for construction of suitable membrane with a high mechanical strength and appropriate surface behavior. Poly (dimethylsiloxane) (PDMS) is electrospun into fine fibers using poly (methyl methacrylate) (PMMA) as the carrier polymer in different weight ratios. Since the surface behavior of all PDMS substrates is moderately hydrophobic (120 < contact angle (CA) < 150), the electrospun membranes with higher PDMS ratios show slightly higher hydrophilicity. Direct plasma treatment is utilized to change the interfacial wettability... 

The creation of surfaces with various super nonwetting properties is an ongoing challenge. We report diverse modifications of novel synthesized zirconia-ceria nanocomposites by different low surface energy agents to fabricate nanofluids capable of regulating surface wettability of mineral substrates to achieve selective superhydrophobic, superoleophobic-superhydrophilic, and superamphiphobic conditions. Surfaces treated with these nanofluids offer self-cleaning properties and effortless rolling-off behavior with sliding angles ≤7° for several liquids with surface tensions between 26 and 72.1 mN/m. The superamphiphobic nanofluid coating imparts nonstick properties to a solid surface whereby... 

TixSi1-xO2 compound thin-film systems were deposited by reactive RF magnetron co-sputtering technique. The effect of Ti concentration on the hydrophilicity of TixSi1-xO2 compound thin films was studied and it was shown that the films with Ti0.6Si0.4O2 composition possess the best hydrophilic property among all the grown samples. Surface ratio and average roughness of the thin films were measured by atomic force microscopy (AFM). Surface chemical states and stoichiometry of the films were determined by X-ray photoelectron spectroscopy (XPS). In addition, XPS revealed that the amount of Ti-O-Si bonds in nanometer depth from the surface of the Ti0.6Si0.4O2 films was the maximum, which resulted...