Sharif Digital Repository

Effect of sandblasting of the copper electrode structures before deposition of gold thin film for micro electrical impedance tomography (EIT) system has been studied experimentally. The comparison has been performed on the unmodified copper electrodes and the sandblasted electrodes before deposition of gold layer, using structural analysis while their performance in EIT system has been measured and analyzed. The results of scanning electron microscopy and atomic force microscopy show that the sandblasting of the electrodes results in the deposition of gold film with smaller grain size and uniformly, comparing to the unmodified structure. The measurement of impedance shows that the... 

Homogenous dispersing of nanoparticles in a base fluid is an excellent way to increase the thermal performance of heat transfer devices especially Heat Pipes (HPs). As a wickless, cheap and efficient heat pipe, Pulsating Heat Pipes (PHPs) are important candidates for thermal application considerations. In the present research an Open Loop Pulsating Heat Pipe (OLPHP) is fabricated and tested experimentally. The effects of working fluid namely, water, Silica Coated ferrofluid (SC ferrofluid), and ferrofluid without surface coating of nanoparticles (ferrofluid), charging ratio, heat input, and application of magnetic field on the overall thermal performance of the OLPHPs are investigated.... 

Finesmigration is a noticeable problem in petroleum-production engineering. Plugging of throats in porous media occurs because of detachment of fine particles from sand surfaces. Thus, the study of interactions between fines and pore surfaces and the investigation of governing forces are important factors to consider when describing the mechanism of the fines-release process. The main types of these forces are electric double-layer repulsion (DLR) and London-van der Waals attraction (LVA). It may be possible to alter these forces with nanoparticles (NPs) as surface coatings. In comparison with repulsion forces, NPs increase the effect of attraction forces. In this paper, we present new... 

Nowadays, superhydrophobic surfaces have attracted a lot of interest because of the wide range of applications in industries. These surfaces can significantly reduce the drag force due to the formation of air gaps between the substrate and liquid interface. The present review mainly focuses on the very recent progresses in the drag reduction studies using superhydrophobic surfaces. Also, a brief discussion about the mathematical modeling and the theories of superhydrophobic surfaces, natural water repellent surfaces, various fabrication techniques with advantages and disadvantages of each method and different properties of the fabricated surfaces in industrial applications is presented.... 

In this study, the anticorrosive effect of dodecylbenzenesulfonicacid-doped polyaniline nanoparticles [n-PANI (DBSA)] as a conductive polymer was investigated using electrochemical impedance spectroscopy (EIS) and X-ray photoelectron spectroscopy (XPS) techniques. Initially, the n-PANI (DBSA) were successfully synthesized via inverse microemulsion polymerization leading to the spherical nanoparticles with an average diameter less than 30 nm. Two coating systems including 1 wt% n-PANI(DBSA) blended epoxy ester (n-PANI(DBSA)/EPE) and neat epoxy ester (EPE) were coated on the carbon steal substrate. The anticorrosion performance of the prepared coatings was studied using EIS measurement in 3.5%... 

In the present paper, an optimization of thermal barrier coating parameters is performed for diesel engine applications. The substrate is A356.0-T7, a cast aluminum alloy which has a vast application in diesel engines, and the alloy is coated by plasma sprayed ZrO2-8 wt.% Y2O3. Parameters including the feed rate of coating powders, the nozzle distance to specimen surfaces, and the coating thickness are optimized by thermal shock fatigue tests and bending tests. Optimum values of the feed rate and the nozzle distance are 30 g/min and 80 mm, respectively, when the objective is considered as maximizing the bending strength. Thermal shock tests demonstrate that lower thickness of coating layers... 

MnCo oxide spinels have received recent interest as surface coatings on ferritic stainless steel (FSS) interconnects in solid oxide fuel cell (SOFC) stacks, where they provide relatively stable electrical conductivity and reduced Cr volatility compared to uncoated FSS interconnects. In this study, sol-gel deposited MnCo surface coatings on FSS, with post-deposition treatments, were investigated in laboratory air at up to 750°C for up to 750h. The protective coating formed and evolved isomorphic crystallites, (Mn,Co,Fe,Cr)3O4, following fifteen (15) fifty hour (50h) cycles in air up to 750°C. Relative to the surface oxide on the uncoated FSS, the coating was dense, crack-free and exhibited... 

A multicomponent lattice Boltzmann scheme is used to investigate the surface coating of substrates with two topographical features by a gravity-driven thin liquid film. The considered topographies are U- and V-shaped grooves and mounds. For the case of substrates with two grooves, our results indicate that for each of the grooves there is a critical width such that if the groove width is larger than the critical width, the groove can be coated successfully. The critical width of each groove depends on the capillary number, the contact angle, the geometry, and the depth of that groove. The second groove critical width depends on, in addition, the geometry and the depth of the first groove;... 

Green's functions of a transversely isotropic half-space overlaid by a thin coating layer are analytically obtained. The surface coating is modeled by a Kirchhoff thin plate perfectly bonded to the half-space. With the aid of superposition technique and employing appropriate displacement potential functions, the Green's functions are expressed in two parts; (i) a closed-form part corresponding to the transversely isotropic half-space with surface kinematic constraints, and (ii) a numerically evaluated part reflecting the interaction between the half-space and the plate in the form of semi-infinite integrals. Some limiting cases of the problem such as surface-stiffened isotropic half-space,... 

There are numerous functions for laser in modern implant dentistry including surface treatment, surface coating, and implant manufacturing. As laser application may potentially improve osseointegration of dental implants, we systematically reviewed the literature for in vitro biological responses to laser-modified or processed titanium dental implants. The literature was searched in PubMed, ISI Web, and Scopus, using keywords “titanium dental implants,” “laser,” “biocompatibility,” and their synonyms. After screening the 136 references obtained, 28 articles met the inclusion criteria. We found that Nd:YAG laser was the most commonly used lasers in the treatment or processing of titanium... 

Superparamagnetic iron oxide nanoparticles with proper surface coatings are increasingly being evaluated for clinical applications such as hyperthermia, drug delivery, magnetic resonance imaging, transfection, and cell/protein separation. To enhance the applicability of magnetic nanoparticles, two main problems must be overcome. First, as the drug coats the particle surface, a significant portion of it is quickly released upon injection (burst effect). Therefore, only small amounts of the drug reach the specific site after, for example, magnetic drug targeting. Second, once the surface-derivatized nanoparticles are inside the cells, the coating is likely digested, leaving the bare particles...