Sharif Digital Repository

In this paper, a Static Synchronous Series Compensator (SSSC) is used to avoid torsional mode instability in a series compensated transmission system. The power system used in this study is the IEEE first benchmark model for Sub-Synchronous Resonance (SSR) analysis. Simulation results in time domain using PSCAD/EMTDC presented and discussed. ©2006 IEEE  

In this study, the steady-state operation of the brushless doubly-fed machine (BDFM) in various modes is physically elaborated and the active power flow and torque analysis are presented for each operating mode alongside confirmatory experimental results on a 4/8 pole D160 size machine. The machine behaviour in asynchronous operating modes is described similar to the conventional induction machines with corresponding pole numbers. Moreover, its performance in synchronous mode is shown to be similar to synchronous machines. On the basis of the above, the BDFM performance is further analysed under two possible fault conditions: first, a controller or converter fault leading to loss of... 

A general model for superconducting synchronous machines in which the rotor can be considered as a magnetic or a nonmagnetic material is proposed and analytically investigated. Analytical equations for magnetic flux in different regions of the machine have been developed. Furthermore, nonlinear magnetization of the iron core is studied. In order to solve the equations in the case of the iron saturation, a reiterative algorithm is proposed. Finite-element simulation has also been performed to verify the equations and the proposed algorithm. The obtained analytical results show good agreement with finite-element method results  

Position sensorless control of ac machines at zero and low speed is possible using high-frequency carrier injection methods. These methods utilize anisotropic properties of rotor. Therefore, they may lose their efficiency for nonsalient machines or machines with small rotor saliency. In these machines, measurement noise and offset, existing delays, as well as model uncertainties may lead to inaccurate estimation of rotor position. Stator resistance which is usually neglected in these methods may also lead to a considerable error especially in machines with small rotor saliency. In this paper, a new position estimation method is presented, and it is shown that in comparison to conventional... 

High frequency (HF) carrier injection schemes can estimate rotor position in a wide speed range. In these methods, first a HF voltage is injected to stator windings and then the corresponding HF current is exploited to estimate the position of rotor using a closed loop tracking observer. The tracking observer is capable to track rotor saliency with no steady state error. However when the motor starts to move or whenever the rotor speed changes a transient error appears. In this paper a new solution is proposed to compensate the transient error in estimation of rotor position  

In this paper a novel supplementary subsynchronous damping controller (SSDC) is proposed for the STATic synchronous COMpensator (STATCOM) which is capable of damping out subsynchronous oscillations in power system with series compensated transmission lines. An auxiliary subsynchronous damping controller (SSDC) for a STATCOM using the generator rotor speed deviation signal as the stabilizing signal has been designed to damp subsynchronous oscillations. Eigenvalue analysis and transient simulations of detailed nonlinear system are considered to investigate the performance of the controller. Robustness of the controller has been analyzed by facing the system with disturbances leading to... 

Sensorless schemes based on HF carrier injection are capable of estimating rotor position in a wide speed range. In these schemes first an additional HF voltage is injected to stator windings. The corresponding HF current is decoupled from main stator currents and the position of the rotor saliency is estimated based on the decoupled HF current in a closed loop tracking observer. The tracking observer is capable of tracking rotor saliency with no steady state error. Transient error appears when the motor starts to move or whenever the rotor speed changes because of any disturbance or any change in the rotor speed command. In this paper a new solution is proposed in order to compensate for... 

Although iron-cored superconducting machine has been recently proposed in many papers for its advantages over conventional air-cored structure such as less cost and less perpendicular magnetic component on HTS tapes it has not been studied analytically yet. This paper analytically investigates a general model for iron-cored superconducting synchronous machine. In this paper, analytical equations for magnetic flux in different regions of machine have been proposed along with an algorithm to solve the equations. The analytical equations will be then used to optimize the thickness of rotor iron in order to maximize the machine power density. Analytical and finite element simulation results will... 

Brushless Doubly-Fed Machine (BDFM) is a machine which incorporates the robustness of the squirrel cage induction machine while having the speed and power factor control of a synchronous machine. A special kind of rotor called Nested-Loop rotor plays an important part in the BDFM, coupling the two stator fields. In future BDFM will share a large part in wind power market. This paper presents a mathematical model of Brushless Doubly-Fed Machine (BDFM) based on Stator Flux Orientation (SFO) in the positive and negative reference frames under unbalanced grid voltage conditions  

An optimum electromagnetic design of a nonsalient magnetic-cored superconducting synchronous machine (SSM) is presented in this paper. First, self- and mutual inductances of a nonsalient magnetic-cored SSM are calculated using the magnetic energy method and analytical equations of magnetic vector potential. Then, a design approach for an SSM machine is proposed based on the inductances of the machine. An optimal design is finally performed using a genetic algorithm, considering the machine efficiency as an objective function. The finite-element method is utilized in each step to verify the analytical results  

In many synchronous digital systems especially those used in mobile applications, the system is exposed to sever shaking that may lead to a failure in the clock generator. In this paper we present an effective method to tolerate the faults on the clock signal that are due to defects in external oscillators. Our technique utilizes no Phase-Lock Loops (PLL), no Delay-Locked Loops (DLL) and no high frequency oscillators because of their drawbacks so that it needs neither more effort to meet Electro-Magnetic Compatibility (EMC) and requirements nor extra hardware to implement DLLs. We have formally evaluated the meta-stability of our technique. This evaluation shows that our technique reliably...