Sharif Digital Repository

In order to convert the postconsumer polyethylene to a valuable product, chlorosulfonation of virgin and highly degraded polyethylene has been carried out in the solution phase under atmospheric pressure. Produced chlorosulfonated polyethylene samples from virgin and degraded HDPE are compounded and cured at different temperatures and their mechanical properties are determined. The results show that degradation of used polyethylene does not have noticeable negative effects on the final mechanical properties of produced chlorosulfonated rubbers. Therefore, it can be concluded that chlorosulfonation can be considered as an effective new method for polyolefin recycling  

This study deals with the thermal conductivity of rubber-based composite friction materials used in railroad vehicles. Based on a commercially available railroad friction material, called here base material (BM), various friction materials containing different thermally conductive fillers (Cu, brass, Al, Al2O3 and talc) are fabricated and then their thermal conductivities are measured at various contents of the fillers. Addition of the thermally conductive fillers causes an increase in thermal conductivity of the friction material from 0.48 up to 5.8 W/m K, depending on the type and content of the filler. In addition, the experimental results reveal that the thermal conductivity of the... 

Rubber particle cavitation has been the focus of many investigations because it dramatically affects the mechanical properties of polymeric blends. In this work, the effect of rubber particle cavitation on the mechanical behavior of high-impact polystyrene was studied. The extent of cavitation in rubber particles was varied via different thermal contraction/expansion cycles in the range of -100 to 23°C. Tensile, creep, and Charpy impact tests were conducted to evaluate the effects of the degree of cavitation on the general mechanical properties. The notch-tip damage zone and deformation micromechanisms were also investigated by a transmitted optical microscopy technique to reveal the effects... 

This study addresses the issue of using recycled materials to obtain low-cost structural products for practical applications. Through the use and re-extrusion of virgin high-density polyethylene (HDPE), the effects of the degradation level of HDPE as a matrix phase on its mechanical properties and the mechanical performance of composites produced with the degraded polyethylene have been examined. The degradation level of HDPE caused by reextrusion has been evaluated by the measurement of the melt flow index and mechanical properties of virgin and degraded HDPEs. The results indicate that the modulus and strength of HDPE significantly increase with the addition of polypropylene filled with 30... 

In the present article, cure kinetics of a commercially available composite friction material used in railroad vehicles is investigated using the rheometer measurements. Effect of ingredients of friction material compound, including rubber matrix, phenolic resin, and fillers, on overall cure kinetics of friction compound is also investigated by comparing the cure kinetics of friction material and rubber matrix compound. A phenomenological model and an Arrhenius-type equation is developed for cure kinetics and induction time of both friction material and rubber matrix. The parameters of the models are extracted from experimental data, using the rheometer at different temperatures and... 

This article examines the physical and mechanical characteristics of mixtures of two different synthetic rubbers, namely styrene-butadiene rubber (SBR) and nitril-butadiene rubber (NBR), with novolac type phenolicresin (PH). According to Taguchi experimental design method, it is shown that the addition of PH increases the crosslinking density of rubber phase probably due to its curative effects. Thermal analysis of the blends indicates that, contrary to NBR/PH blend, thermal stability of SBR/PH blend is dependent on sulfur content due to predominant polysulfidic crosslinks formed in SBR. Slight shift in glass-transition temperature (Tg) of pure SBR and NBR vulcanizates by the addition of PH... 

Mechanical properties and fracture toughness micromechanisms of copolypropylene filled with different amount of nanometric CaCO3 (5-15 wt %) were studied, J-integral fracture toughness was incorporated to measure the effect of incorporation of nanoparticle into PP matrix. Crack-tip damage zones and fracture surfaces were studied to investigate the effect of nanofiller content on fracture toughness micromechanisms. It was found that nanofiller acted as a nucleating agent and decreased the spherulite size of polypropylene significantly, J-integral fracture toughness (Jc) of nanocomposites was improved dramatically. The Jc value increased up to approximately two times that of pure PP at 5 wt %... 

The present study deals with the structure-property relationship of organoclay (OC) filled nanocomposites based on rubber blend comprising of nitrile-butadiene rubber (NBR) and phenolic resin (PH). To obtain a better insight into the characteristics of the NBR/PH/OC hybrid system, a simple model system consisting of NBR/OC nanocomposites is also taken into consideration. A series of NBR/OC and NBR/PH/OC nanocomposites containing a wide range of OC concentrations (2.5-30 phr) are prepared by using traditional open two-roll mill. Structural analysis performed by X-ray diffraction (XRD), scanning electron microscope (SEM), and transmission electron microscope (TEM) exhibits mixed exfoliated and...