Sharif Digital Repository

One of the miscellaneous units that are frequently used in water and wastewater systems is flush tank. Flush tank increases the self cleaning velocity in the conduit, and helps to clear the conduits from deposits and contaminations. While these units have been used for many years, there is not enough information about the hydraulic performance of these units in respect to the discharge, distance from the tank and the pipe hydraulics. In this paper the experimental results from observed hydrographs at different distances from the flush tank in a pipe has been presented. The variables include; volume of releasing water (or inlet hydrograph), upstream head, pipe diameter (3 cm), pipe length and... 

In this article, a genetic algorithm is used to optimize the separator pressures in a multistage crude oil and multistage gas condensate production unit with four and three separators respectively. This leads to the generation of more accurate results for the quality and quantity of oil remaining in the stock tank for both crude oil and gas condensate production units. Genetic-based optimized pressures for crude oil separators resulted in 1.8% and 2% enhancement in oil remaining in the stock tank for summer and winter respectively. API gravity of the stock tank oil was improved 2.4% in summer and 2.2% in winter. For the gas condensate production unit, optimized pressures can enhance by 8.6%... 

In order to be more precise to find primary cosmic particles directions, nowadays detectors and data analysis for studying secondary particles in extensive air showers have an ongoing progress and water Cherenkov detector is considered as a secondary particle detector. Our aim in this paper is to optimize the size and the inner surface characteristic of a cylindrical water Cherenkov tank with one PMT. By comparing simulation outputs with experiments results, we show that the diffusing inner surface is more practical than the reflective inner surface and we conclude that the optimum height for a diffusing tank with a diameter of 45cm is 60cm  

The hydraulic performances of drain pipes are very important in drainage projects and systems. Usually these pipes are used in a saturated soil to decrease the water table to a favorable level or, drain the excess water. However, drain pipes can be used in a water or wastewater tank for different purposes such as selective withdrawal. There are not much published documents on the performance of drain pipes in submerged situations. Therefore, the aim of this study was to examine the performance of drain pipe in a submerged tank. For this, a horizontal pipe of 26.5 mm inner diameter, 5 meter long with 48 circular drain inlets of 10 mm diameter at equal distances along the pipe have been tested... 

A new switching method for the stabilisation of a one-dimensional capacitor array tank for the stepwise charging of a load capacitor is presented. In this method, the tank capacitor configuration is rearranged in a circular manner once the charging process of a load capacitor finishes and before the charging process of a new load capacitor begins. Unlike previously reported methods, this method does not require backward switching for the stabilisation of tank capacitor voltages. Hence, the proposed method reduces the number of charging process steps by a factor of up to 2 compared with the conventional method. Moreover, since the tank recycles its charge inherently, the capacitive load can... 

The current sources in power transformers such as leads and windings are also sources of Eddy current losses. Due to these losses some parts of tank wall are subject to serious local overheating. It affects the safety and reliability of these expensive objects and their power delivery. There are various methods for reduction of these eddy current losses. One of them is the internal shielding of transformer tank wall. In this paper the tank eddy current losses reduction, through its shielding is determined. ©2009 IEEE  

This paper investigates the static and dynamic buckling of an anchored cylindrical steel tank subjected to horizontal and vertical ground acceleration. The buckling capacity of the tank is estimated using static pushover (SPO) and incremental dynamic analyses (IDA). Appropriate load patterns due to the horizontal and vertical components of ground excitations are utilized for SPO analyses. The buckling capacity curves and critical buckling loads computed using SPO analyses are compared to those obtained from IDA. A proper vertical to horizontal acceleration ratio (av/ah) for SPO analysis is proposed that leads to good agreement between SPO and IDA results. © 2017  

A new small array of cherenkov detectors has been deployed in Tehran, 1200 m above sea level. This array contains of four tanks full of distilled water with diameter of 64 cm and height of 130 cm. The effective area of each tank is about 6.5 × 103cm2 . They are used to detect the air showers and to record the arrival time of the secondary particles. We have collected about 486643 EAS in 5270 h of observation time from Nov-2006 to May-2007. We find zenith and azimuth distribution of EAS with this array. A cosn θ distribution with n = 7.3±0.1 was obtained for zenith angle. Since this tank of distilled water is cheaper and more available than Scintillators it is preferable to use them instead... 

In this paper, the seismic response of anchored cylindrical steel tanks with various dimensional parameters has been investigated by endurance time method considering fluid-structure interaction effects. Various response quantities, such as stresses and displacements, have been evaluated by subjecting tanks to specially designed intensifying accelerograms and their performance is judged based on their response at predefined level(s) of dynamic excitation. It is shown that ET analysis can reliably predict the result of ground motion time history analysis in all seven tank models studied. In four of the tanks in which height of the shell and the level of fluid is the same, the variation of... 

A numerical model based on the boundary element method is proposed for the sloshing of a flowing liquid in a three-dimensional tank. Assuming a mean flow in the tank in addition to a perturbation flow, the nonlinear boundary conditions of the liquid free-surface are linearized. Using the boundary element method along with the modal analysis technique a reduced order model is obtained which is used to calculate the fundamental sloshing frequencies and modes in the tank with an inlet and outlet. The obtained results for a test case are compared with the literature data to validate the proposed model. The results are in a very good agreement with analytical results and show an acceptable... 

The biodegradability rates of two different kinds of polyethylene bonded with corn and potato starch are studied in this paper. While it is usual to use soil as the environment for biodegradation, an aerated sludge tank was used in this studywhich offers a richermicrobialmediumand increases the rate of biodegradation. The biodegradability is determined by two ways: first, comparing differences in the weight change of two samples, one placed inside distilled water and the other placed in aerated sludge tank. Second test for biodegradation is by examination of FTIR spectroscopy. Through FTIR spectroscopy, the biodegradability rate and reduction in some of the existing bonds in polymer before... 

In order to be more precise to find primary cosmic particles directions, nowadays detectors and data analysis for studying secondary particles in extensive air showers have an ongoing progress and water Cherenkov detector is considered as a secondary particles detector. Our aim in this paper is to optimize the size and the inner surface characteristic of a cylindrical water Cherenkov tank with one PMT in order to use at the Alborz observatory air shower array which consists of 20 plastic scintillation detectors and 10 water Cherenkov detectors. By comparing data gathered by tanks with diffusing and specular reflection inner surfaces, we show that the diffusing inner surface is more... 

Using hybrid energy storage system is a method for increasing the storage capability of solar thermal energy. If multiple energy storage devices with complementary performance characteristics are used together, the resulting system will be a 'Hybrid Energy Storage System'. In other words, a Hybrid Energy Storage System (HESS) has several media available for storage at any time. In this way, increase in storable energy is obtained without increasing collectors' area. When there are more than one storage mediums, the system should be able to choose the best medium for storing energy according to the conditions. In the previous works, an optimizer program was used to find the proper medium... 

In this study, a transformer model is proposed to simulate the behaviour of a real transformer, under presence ofdifferent types of defects which contribute to partial discharge (PD) generation, as closely as possible. Five different typesof defects (scratch on winding insulation, bubble in oil, moisture in insulation paper, very small free metal particle intransformer tank and fixed sharp metal point on transformer tank) are implemented artificially into these transformermodels to investigate the resultant PD current signal magnitude and characteristics. Time-domain PD currentwaveforms are recorded on those transformer models which have one type of those defects. The resultant statisticalPD... 

Simulation, design and fabrication of a sealing enclosure is carried out for a NaI(Tl) 2″×2″ detector, to be used as in situ gamma radioactivity measurement system in marine environment. Effect of sealing enclosure on performance of the system in laboratory and marine environment (distinct tank with 10 m3 volume) were studied using point sources. The marine volumetric efficiency for radiation with 1461 keV energy (from 40K) is measured with KCl volumetric liquid source diluted in distinct tank. The experimental and simulated efficiency values agreed well. Marine volumetric efficiency calibration curve is calculated for 60 keV to 1461 keV energy with Monte Carlo method. This curve indicates... 

In this study, the mass transfer evaluation of an agitated liquid-liquid system for the extraction of molybdenum and tungsten from aqueous sulfate solution was investigated. It was found from batch experiments for separation of molybdenum from tungsten that the initial aqueous pH, Cyanex272 and D2EHPA concentration, contact time, dispersed phase volume fraction and impeller speed were optimized at 1.3, 0.07 M, 0.29 M, 15 min, 0.09 and 280 rpm, respectively. The results indicate that a suitable composition for stripping is 1.5 M NH4OH and 0.6 M NH4F. Furthermore, a modified correlation based on dimensionless numbers was derived for the prediction of continuous phase mass transfer in the... 

In this paper, an analytic model of the energy consumption of the Stepwise Adiabatic Circuits (SAC) when it is possible to discharge the load capacitor is proposed. Using this model, analytical derivations are calculated which shows us the power saving of the SACs. Using analytical derivations, the sizing of a capacitor tank is determined for a desired energy saving. For example, the derivations predict that if the sizing of the 3-step series tank capacitors is equal to the load capacitor, the power saving is 55%. Also, if the sizing of the tank is very large the energy saving of a 3-step stepwise charging is equal to 66.7%. Several Simulations in 0.18μm CMOS technology prove the accuracy of... 

In this study, the mass transfer evaluation of an agitated liquid-liquid system for the extraction of molybdenum and tungsten from aqueous sulfate solution was investigated. It was found from batch experiments for separation of molybdenum from tungsten that the initial aqueous pH, Cyanex272 and D2EHPA concentration, contact time, dispersed phase volume fraction and impeller speed were optimized at 1.3, 0.07 M, 0.29 M, 15 min, 0.09 and 280 rpm, respectively. The results indicate that a suitable composition for stripping is 1.5 M NH4OH and 0.6 M NH4F. Furthermore, a modified correlation based on dimensionless numbers was derived for the prediction of continuous phase mass transfer in the... 

In this research, a new transient mathematical model based upon tanks-in-series configuration was developed to simulate the direct synthesis of dimethyl ether (DME) from syngas in a commercial-scale slurry bubble column reactor. A comparison between the simulation results and experimental data showed that the applied model might acceptably describe the behavior of the slurry reactor. Furthermore, simulation results in the heterogeneous bubble flow regime indicated that the proposed model with 10 tanks-in-series provided the optimum condition. Utilizing this transient model and considering catalyst deactivation, the effect of operating conditions on DME productivity and CO conversion were... 

The overall design of cold gas propulsion systems is pretty complicated when considering the mission requirements, operating constraints and functional limitations imposed by the mechanical components. To address this complication, a precise design process is proposed, which attempts to optimize the cost of operation as well as to minimize the waste volume and weight by using multi-objective trade-off analysis. This analysis is based on a set of ordinary differential equations that are solved iteratively to describe the optimal behavior of the system. Therefore, a numerical code is being developed to give insight on the design sensitivity with respect to uncertainties on the design...